Dtc C1379 Downhill Assist Control Switch Malfunction (Test Mode Dtc)
Brake. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35
DESCRIPTION
WIRING DIAGRAM
INSPECTION PROCEDURE
READ VALUE USING INTELLIGENT TESTER (DOWNHILL ASSIST CONTROL SWITCH)
PERFORM TEST MODE (SIGNAL CHECK)
INSPECT DOWNHILL ASSIST CONTROL SWITCH
CHECK HARNESS AND CONNECTOR (DOWNHILL ASSIST CONTROL SW - SKID CONTROL ECU/BODY GROUND)
DTC C1379 Downhill Assist Control Switch Malfunction (Test Mode DTC) |
DESCRIPTION
DTC C1379 will be cleared when the downhill assist control switch sends a downhill assist control operation signal or when Test Mode ends. DTC C1379 is stored only in Test Mode.DTC Code
| DTC Detection Condition
| Trouble Area
|
C1379
| Stored only during Test Mode.
| Downhill assist control switch
|
WIRING DIAGRAM
INSPECTION PROCEDURE
- NOTICE:
- When replacing the brake actuator assembly, perform zero point calibration (RAV4_ACA30 RM000001K1O00SX.html).
1.READ VALUE USING INTELLIGENT TESTER (DOWNHILL ASSIST CONTROL SWITCH) |
Check the Data List for proper functioning of the downhill assist control switch.
ABS/VSC/TRC:Tester Display
| Measurement Item/Range
| Normal Condition
| Diagnostic Note
|
Downhill Assist Control Switch
| Downhill assist control switch / ON or OFF
| ON: Downhill assist control switch is on OFF: Downhill assist control switch is off
| -
|
- OK:
- The intelligent tester displays ON or OFF according to downhill assist control switch operation.
2.PERFORM TEST MODE (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure (RAV4_ACA30 RM0000022CZ007X.html).
- OK:
- All Test Mode DTCs are cleared.
- HINT:
- If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (RAV4_ACA30 RM000000OS701UX.html).
3.INSPECT DOWNHILL ASSIST CONTROL SWITCH |
Turn the ignition switch off.
Make sure that there is no looseness in the locking part and connecting part of the connector.
Disconnect the downhill assist control switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
| Switch Condition
| Specified Condition
|
1 - 4
| Switch is pushed
| Below 1 Ω
|
Switch is not pushed
| 10 kΩ or higher
|
- NOTICE:
- Check the downhill assist control switch signal after replacement (RAV4_ACA30 RM0000022CZ007X.html).
4.CHECK HARNESS AND CONNECTOR (DOWNHILL ASSIST CONTROL SW - SKID CONTROL ECU/BODY GROUND) |
Disconnect the skid control ECU connector.
Disconnect the downhill assist control switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
| Condition
| Specified Condition
|
A67-29 (HDCS) - E36-4
| Always
| Below 1 Ω
|
A67-29 (HDCS) - Body ground
| Always
| 10 kΩ or higher
|
E36-1 - Body ground
| Always
| Below 1 Ω
|
- HINT:
- If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (RAV4_ACA30 RM000000OS701UX.html).
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|