Anti-Lock Brake System Dtc Check / Clear

Brake. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35
Brake Control. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35

  1. CHECK DTC (When Using Intelligent Tester)

  1. CLEAR DTC (When Using Intelligent Tester)

  1. CHECK DTC (When not Using Intelligent Tester)

  1. CLEAR DTC (When not Using Intelligent Tester)

  1. END OF DTC CHECK/CLEAR

Anti-Lock Brake System -- Dtc Check / Clear



CHECK DTC (When Using Intelligent Tester)


    Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.Brake Control.Anti-Lock Brake System.Anti-Lock Brake System Dtc Check / Clear

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Read the DTCs by following the prompts on the tester screen.

    HINT:
    Refer to the intelligent tester operator's manual for further details.

CLEAR DTC (When Using Intelligent Tester)


    Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.Brake Control.Anti-Lock Brake System.Anti-Lock Brake System Dtc Check / Clear

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Operate the intelligent tester to clear the codes.

    HINT:
    Refer to the intelligent tester operator's manual for further details.

CHECK DTC (When not Using Intelligent Tester)


    Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.Brake Control.Anti-Lock Brake System.Anti-Lock Brake System Dtc Check / Clear

  1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

    SST
    09843-18040

  2. Turn the ignition switch to ON.

  3. w/o Multi-information display: Read DTCs from the ABS warning light on the combination meter.

  4. w/ Multi-information display: Read DTCs from the ABS warning light and the multi-information display on the combination meter.

    HINT:
    1. If the ABS warning light does not blink, perform the relevant troubleshooting procedures. The relevant troubleshooting procedures are instructed in the sections listed in the table below.
      Section Title
      		See Page
      ABS Warning Light does not Come ON
      		RAV4_ACA30 RM000000OSG01VX.html
      TC and CG Terminal Circuit
      		RAV4_ACA30 RM000000OSL01RX.html

    2. As an example, the illustration below shows the blinking patterns of the normal system code and trouble codes 11 and 21 for the ABS, and display of the normal system code and trouble code 11 and 21 for the ABS on the multi information display. As an example, the blinking patterns of the normal system code and DTCs 11 and 21 are shown below.


      Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.Brake Control.Anti-Lock Brake System.Anti-Lock Brake System Dtc Check / Clear

    3. DTCs are explained in "DIAGNOSTIC TROUBLE CODE CHART" (RAV4_ACA30 RM000001RVL009X.html).

  5. After completing the check, disconnect SST from terminals 13 (TC) and 4 (CG) of the DLC3, and turn the ignition switch off.

    HINT:
    If 2 or more malfunctions are detected at the same time, the lowest numbered DTC is displayed first.

CLEAR DTC (When not Using Intelligent Tester)


    Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.Brake Control.Anti-Lock Brake System.Anti-Lock Brake System Dtc Check / Clear

  1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

    SST
    09843-18040

  2. Turn the ignition switch to ON.



    3. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35

  3. Clear the DTCs stored in the skid control ECU by depressing the brake pedal 8 times or more within 5 seconds.

  4. Check that the warning light blinks in the normal system code pattern.

  5. Remove SST from the terminals of the DLC3.

  6. Turn the ignition switch off.


END OF DTC CHECK/CLEAR

  1. Turn the ignition switch to ON.

  2. Check that the ABS warning light goes off within approximately 3 seconds.

  3. Turn the ignition switch off.