Dtc P2716 Pressure Control Solenoid D Electrical (Shift Solenoid Valve Slt)

Transmission. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35
U151F Automatic Transaxle. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35

DESCRIPTION

MONITOR DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)

CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

INSPECT SHIFT SOLENOID VALVE SLT

DTC P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)


DESCRIPTION

Refer to DTC P2714 (RAV4_ACA30 RM000000W8307RX_01.html).

DTC No.
DTC Detection Condition
Trouble Area
P2716
Conditions (a) and (b) below are detected for 1 sec. or more (1 trip detection logic):
(a) SLT - terminal: 0 V
(b) SLT - terminal: 12 V
  1. Open or short in shift solenoid valve SLT circuit
  2. Shift solenoid valve SLT
  3. ECM

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLT circuit is detected, the ECM interprets this as a fault. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

Refer to DTC P2714 (RAV4_ACA30 RM000000W8307RX_08.html).

INSPECTION PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)


    Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.U151F Automatic Transaxle.Automatic Transaxle System. Dtc P2716 Pressure Control Solenoid D Electrical (Shift Solenoid Valve Slt)

  1. Disconnect the transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Condition
    		Specified Condition
    2 (SLT+) - 8 (SLT-)
    		20°C (68°F)
    		5.0 to 5.6 Ω
    2 (SLT+) - Body ground
    		Always
    		10 kΩ or higher
    8 (SLT-) - Body ground
    		Always
    		10 kΩ or higher


NG
Go to step 3
OK


2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

  1. Connect the transmission wire connector.



    Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.U151F Automatic Transaxle.Automatic Transaxle System. Dtc P2716 Pressure Control Solenoid D Electrical (Shift Solenoid Valve Slt)

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Condition
    		Specified Condition
    B96-11 (SLT+) - B96-10 (SLT-)
    		20°C (68°F)
    		5.0 to 5.6 Ω
    B96-11 (SLT+) - Body ground
    		Always
    		10 kΩ or higher
    B96-10 (SLT-) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (for 2GR-FE) (RAV4_ACA30 RM0000017UO01GX.html)

3.INSPECT SHIFT SOLENOID VALVE SLT


    Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.U151F Automatic Transaxle.Automatic Transaxle System. Dtc P2716 Pressure Control Solenoid D Electrical (Shift Solenoid Valve Slt)

  1. Remove the shift solenoid valve SLT.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Condition
    		Specified Condition
    1 - 2
    		20°C (68°F)
    		5.0 to 5.6 Ω

  1. Connect the battery's positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

    OK:
    Valve moves and makes operating sound.


NG
REPLACE SHIFT SOLENOID VALVE SLT (RAV4_ACA30 RM0000027NY00CX.html)
OK

REPAIR OR REPLACE TRANSMISSION WIRE (RAV4_ACA30 RM000001SU1017X.html)