Dtc C1425 Open In Stop Light Switch Circuit


DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)

RECONFIRM DTC

INSPECT STOP LIGHT CONTROL ECU ASSEMBLY

CHECK TERMINAL VOLTAGE (STP)

RECONFIRM DTC

DTC C1425 Open in Stop Light Switch Circuit


DESCRIPTION

The skid control ECU (brake actuator assembly) detects the brake operating conditions through a signal transmitted by the stop light switch assembly.

DTC Code
DTC Detection Condition
Trouble Area
C1425
When the IG1 terminal voltage is between 9.5 and 17.4 V, an open STP terminal circuit continues for 3 seconds or more.
  1. STP terminal circuit
  2. Stop light control ECU assembly
  3. Skid control ECU (Brake actuator assembly)

WIRING DIAGRAM


Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Brake Control Dynamic Control Systems.Anti-Lock Brake System. Dtc C1425 Open In Stop Light Switch Circuit


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (brake actuator assembly), perform calibration (LandCruiser RM000000XHR0BJX.html).
1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)

  1. Turn the ignition switch off

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Stop Light SW
    		Stop light switch/ON or OFF
    		ON: Brake pedal depressed
    OFF: Brake pedal released
    		-

  1. Check that the stop light switch display observed on the intelligent tester changes according to the brake pedal operation.

    OK:
    The intelligent tester displays ON or OFF according to brake pedal operation.


NG
Go to step 3
OK


2.RECONFIRM DTC

  1. Clear the DTCs (LandCruiser RM000000XHV0KEX.html).

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is output (LandCruiser RM000000XHV0KEX.html).

    Result
    Result
    		Proceed to
    DTC is not output
    		A
    DTC is output
    		B


B
REPLACE BRAKE ACTUATOR ASSEMBLY (LandCruiser RM0000034UX02TX.html)
A

USE SIMULATION METHOD TO CHECK (LandCruiser RM000003YMJ00XX.html)

3.INSPECT STOP LIGHT CONTROL ECU ASSEMBLY

  1. Inspect the stop light control ECU assembly (LandCruiser RM000001ZTV09QX.html).



NG
REPLACE STOP LIGHT CONTROL ECU ASSEMBLY (LandCruiser RM000003MWQ02KX.html)
OK


4.CHECK TERMINAL VOLTAGE (STP)

  1. Make sure that there is no looseness at the locking parts and connecting parts of the connectors.

  1. Disconnect the A6 skid control ECU (brake actuator assembly) connector.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Brake Control Dynamic Control Systems.Anti-Lock Brake System. Dtc C1425 Open In Stop Light Switch Circuit

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Condition
    		Specified Condition
    A6-2 (STP) - Body ground
    		Brake pedal depressed
    		8 to 14 V
    Brake pedal released
    		Below 1.5 V
    Text in Illustration
    *a
    		Front view of wire harness connector
    (to Skid Control ECU [Brake Actuator Assembly])


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.RECONFIRM DTC

  1. Clear the DTC (LandCruiser RM000000XHV0KEX.html).

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is output (LandCruiser RM000000XHV0KEX.html).

    Result
    Result
    		Proceed to
    DTC is not output
    		A
    DTC is output
    		B


B
REPLACE BRAKE ACTUATOR ASSEMBLY (LandCruiser RM0000034UX02TX.html)
A

USE SIMULATION METHOD TO CHECK (LandCruiser RM000003YMJ00XX.html)