Common Rail Installation

Install the common rail and No. 2 intake manifold insulator with the 2 bolts.

Torque:

38 N*m{387 kgf*cm, 28 ft.*lbf}

Connect the 2 connectors.

Temporarily install the fuel inlet pipe with the union nuts.

NOTICE:

1. When replacing the common rail, it is necessary to replace the 4 injection pipes and fuel inlet pipe with new ones.
   
2. Be careful that dust, dirt or any other foreign matter does not contact the joint area of the fuel inlet pipe.
   

Using a 17 mm union nut wrench, tighten the fuel inlet pipe union nut on the common rail side.

Torque:

35 N*m{357 kgf*cm, 26 ft.*lbf}

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Toyota Fortuner RM000000UYX010X.html).

Using a 17 mm union nut wrench, tighten the fuel inlet pipe union nut on the supply pump side.

Torque:

35 N*m{357 kgf*cm, 26 ft.*lbf}

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Toyota Fortuner RM000000UYX010X.html).

Install a new O-ring to the engine oil level dipstick guide.

Install the engine oil level dipstick guide with the bolt.

Torque:

8.0 N*m{82 kgf*cm, 71 in.*lbf}

Install the clamp with the bolt.

Torque:

5.0 N*m{51 kgf*cm, 44 in.*lbf}

Install the engine oil level dipstick.

Temporarily install the No. 2 nozzle leakage pipe with the 3 bolts.

Temporarily install a new gasket and the union bolt.

Tighten the 3 bolts and union bolt.

Torque:

for bolt:

13 N*m{130 kgf*cm, 9 ft.*lbf}

for union bolt:

21 N*m{214 kgf*cm, 15 ft.*lbf}

Connect the 3 fuel hoses.

Temporarily install the No. 4 injection pipe with the union nuts.

Install the 2 bolts.

Torque:

13 N*m{130 kgf*cm, 9 ft.*lbf}

NOTICE:

1. If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection clamp with a new one.
   
2. Make sure that the inner-rubbers of the injection pipe fit inside the clamps.
   
3. When installing the pipe, check that the inner-rubbers and the clamps are in their proper positions.
   

Using a 17 mm union nut wrench, tighten the injection pipe union nut on the common rail side.

Torque:

35 N*m{357 kgf*cm, 26 ft.*lbf}

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Toyota Fortuner RM000000UYX010X.html).

Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.

Torque:

35 N*m{357 kgf*cm, 26 ft.*lbf}

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Toyota Fortuner RM000000UYX010X.html).

Temporarily install the No. 1, No. 2 and No. 3 injection pipes with the union nuts.

Install the No. 2 and No. 3 injection pipe clamps with the bolt and 2 nuts, as shown in the illustration.

Torque:

5.0 N*m{51 kgf*cm, 44 in.*lbf}

HINT:

If the painted mark on the No. 1 injection pipe has disappeared, use the illustration as a reference to install the clamps.

Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the common rail side.

Torque:

35 N*m{357 kgf*cm, 26 ft.*lbf}

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Toyota Fortuner RM000000UYX010X.html).

Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.

Torque:

35 N*m{357 kgf*cm, 26 ft.*lbf}

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Toyota Fortuner RM000000UYX010X.html).

Check and clean the oil filter installation surface.

Apply clean engine oil to the gasket of a new oil filter.

Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.

Using SST, tighten the oil filter. Depending on the work space available, choose from the following.

SST

09228-07501

1. If enough space is available, use a torque wrench to tighten the oil filter.
   

   Torque:

   12 N*m{122 kgf*cm, 9 ft.*lbf}

2. If enough space is not available to use a torque wrench, tighten the oil filter 3/4 turn by hand or with a common wrench.
   

Install the manifold stay with the 2 bolts.

Torque:

19 N*m{194 kgf*cm, 14 ft.*lbf}

HINT:

Make sure the stay's indented area (labeled A) must face the manifold.

Wipe the oil pan and drain plug.

Install a new gasket and the drain plug.

Torque:

34 N*m{347 kgf*cm, 25 ft.*lbf}

Add new oil.

Standard oil capacity:

Item	Specified Condition
Drain and refill with oil filter change	6.9 liters (7.3 US qts, 6.1 Imp. qts)
Drain and refill without oil filter change	6.6 liters (7.0 US qts, 5.8 Imp. qts)
Dry fill	7.4 liters (7.8 US qts, 6.5 Imp. qts)

Install the oil filler cap.

Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

NOTICE:

1. Hand pump pumping speed: Max. 2 strokes/ sec.
   
2. The hand pump must be pushed with a full stroke during pumping.
   
3. When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
   
4. If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
   
5. If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
   
6. If air bleeding using the hand pump is incomplete, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.
   

Start the engine.

NOTICE:

1. Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.
   
2. Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
   
3. Use a fully-charged battery.
   

1. When the engine can be started, proceed to the next step.
   

2. If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
   

Turn the ignition switch off.

Connect the intelligent tester to the DLC3.

Turn the ignition switch to ON and turn the intelligent tester on.

Clear the DTCs (Toyota Fortuner RM0000012WY005X.html).

Start the engine.*1

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2

Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3

Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

HINT:

When the Active Test "Test the Fuel Leak" is used to change the pump control mode, the actual fuel pressure inside the common rail drops below the target fuel pressure when the Active Test is off, but this is normal and does not indicate a pump malfunction.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Read Current DTCs.

Clear the DTCs (Toyota Fortuner RM0000012WY005X.html).

HINT:

It is necessary to clear the DTCs as DTC P1604 or P1605 may be stored when air is bled from the fuel system after replacing or repairing fuel system parts.

Repeat steps *1 to *3.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Read Current DTCs.

OK:

No DTCs are output.

Check that there are no leaks from any part of the fuel system when the engine is stopped. If there is fuel leakage, repair or replace parts as necessary.

Start the engine and check that there are no leaks from any part of the fuel system. If there is fuel leakage, repair or replace parts as necessary.

Disconnect the return hose from the common rail.

Start the engine and check for fuel leaks from the return pipe.
If there is fuel leakage, replace the common rail.

Connect the intelligent tester to the DLC3.

Start the engine and push the intelligent tester main switch on.

Select the Fuel Leak test from the Active Test mode on the intelligent tester.

If the intelligent tester is not available, fully depress the accelerator pedal quickly. Increase the engine speed to the maximum and maintain that speed for 2 seconds. Repeat this operation several times.

Check that there are no leaks from any part of the fuel system.

NOTICE:

A return pipe leakage of less than 10 cc (0.6 cu in.) per minute is acceptable.

Reconnect the return hose to the common rail.

Warm up the engine, stop the engine and wait for 5 minutes. The oil level should be between the dipstick's low and full level marks.
If the oil level is low, check for leakage and add oil up to the full level mark.

NOTICE:

Do not add engine oil above the full level mark.

Install the under cover with the 4 bolts.

Torque:

28 N*m{286 kgf*cm, 21 ft.*lbf}

Install the under cover with the 8 bolts.

Torque:

28 N*m{286 kgf*cm, 21 ft.*lbf}