Dtc P0093 Fuel System Leak Detected - Large Leak


DESCRIPTION

MONITOR DESCRIPTION

MONITOR STRATEGY

INSPECTION PROCEDURE

CHECK FOR FUEL LEAKS (IN HIGH-PRESSURE AREAS)

CHECK FOR ANY OTHER DTC OUTPUT (PROCEDURE 2) (IN ADDITION TO DTC P0093 AND RECORD STORED DTC AND FREEZE FRAME DATA)

CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)

ADD FUEL

CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)

CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VAL #1 TO #4)

READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)

READ VALUE USING INTELLIGENT TESTER (INJECTION FEEDBACK VAL #1 TO #4)

PERFORM ENGINE SPEED ACCELERATION

CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER

BLEED AIR FROM FUEL SYSTEM

PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK)

PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)

REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER

REPLACE FUEL INJECTORS OF ALL CYLINDERS

BLEED AIR FROM FUEL SYSTEM

REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING

READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)

INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)

INSPECT FUEL TEMPERATURE SENSOR (SENSOR OUTPUT)

CHECK FOR INTERMITTENT PROBLEMS

REPLACE CRANKSHAFT POSITION SENSOR

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - FUEL PRESSURE SENSOR)

INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)

REPLACE COMMON RAIL ASSEMBLY

BLEED AIR FROM FUEL SYSTEM

REPLACE FUEL TEMPERATURE SENSOR

CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)

DTC P0093 Fuel System Leak Detected - Large Leak


DESCRIPTION

A fuel pressure sensor mounted on the common rail converts the fuel pressure inside the common rail into an electrical signal, and outputs it to the ECM. The ECM controls the supply pump in order to maintain the fuel pressure inside the common rail at a target pressure calculated by the ECM. Refer to System Description (Toyota Fortuner RM0000012WW024X.html).
HINT:
  1. If the drop in the internal fuel pressure is large when injecting fuel, the ECM interprets this as a fault and stores P0093.
  2. If P0093 is present, refer to the "Diagnostic Trouble Code (DTC) Table for Common Rail System" (Toyota Fortuner RM0000012WW024X.html).

P0093
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
After idling for 60 seconds, run engine at 2500 rpm for 30 seconds.
Fully depress the accelerator pedal for 5 seconds, and then release it. (*A)
Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*B)
Repeat procedures (*A) and (*B) 5 times.
Fuel leaks in high-pressure areas
(1 trip detection logic)
  1. Fuel line between supply pump and common rail
  2. Fuel line between common rail and each injector
  3. Supply pump
  4. Common rail
  5. Fuel injector
  6. Pressure discharge valve (common rail)
  7. Fuel pressure sensor (common rail)
  8. Crankshaft position sensor
  9. Fuel filter
  10. Open or short in EDU circuit (P0200 set simultaneously)
  11. Open or short in injector circuit
  12. EDU (P0200 set simultaneously)
  13. ECM

Related Data List
DTC No.
Data List
P0093
  1. Fuel Press
  2. Target Common Rail Pressure
HINT:
When DTC P0093 is set, check the internal fuel pressure of the common rail by entering the following menus on the intelligent tester: Powertrain / Engine / Data List / Fuel Press.

Reference:

Engine Speed
Fuel Pressure
Idling
Approximately 30000 to 40000 kPa
3000 rpm (No engine load)
Approximately 30000 to 60000 kPa

MONITOR DESCRIPTION

P0093 (Fuel leaks in high-pressure areas):
  1. This DTC indicates that fuel leaks exist in high pressure areas in the common rail system. The ECM constantly monitors the internal fuel pressure of the common rail after the engine is started. The ECM sets this DTC if the drop in the internal fuel pressure is large when injecting fuel.
    In the common rail system, high-pressure fuel is always supplied to the high-pressure areas including the supply pump, common rail, injectors and piping. The ECM adjusts the suction control valve opening angle to obtain the target internal fuel pressure.
    If this DTC is set, the ECM enters fail-safe mode. Fail-safe mode suspends both fuel injection and supply pump operation, and then stops the engine. Before stopping the engine, the ECM permits the vehicle to be driven for 1 minute. Fail-safe mode continues until the ignition switch is turned OFF.

MONITOR STRATEGY


Required sensors
Fuel pressure sensor
Frequency of operation
Continuous
Duration
1 second
MIL operation
1 driving cycle

INSPECTION PROCEDURE

NOTICE:
  1. Soon after starting the engine, visually check for fuel leaks in the fuel line.
  2. After replacing the ECM, the new ECM needs registration (Toyota Fortuner RM0000012XK030X.html) and initialization (Toyota Fortuner RM0000012X2005X.html).
  3. After replacing the fuel supply pump, the ECM needs initialization (Toyota Fortuner RM0000012X2005X.html).
  4. After replacing a fuel injector, the ECM needs registration (Toyota Fortuner RM0000012XK030X.html).
HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.1Kd-Ftv Engine Control System.Ecd System. Dtc P0093 Fuel System Leak Detected - Large Leak

HINT:
  1. The following can be deduced from the above freeze frame data:
    1. The common rail fuel pressure dropped suddenly when the engine was being run at a moderate engine speed during engine warmup and DTC P0093 was stored at the point when data set 4 was recorded.
    2. Injection Feedback Val #3 is 5.0 mm3/st which is large (the normal value is between -3.0 and 3.0 mm3/st) and indicates that the injector of cylinder 3 may be malfunctioning.
  2. Actual cause: In this case, foreign matter in the fuel is stuck inside an injector causing the injector to malfunction temporarily.
    In order to remove the foreign matter in the fuel (the major cause of the problem), the fuel filter case needs to be cleaned and the fuel filter needs to be replaced.

Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.1Kd-Ftv Engine Control System.Ecd System. Dtc P0093 Fuel System Leak Detected - Large Leak

HINT:
*1: Fuel Press suddenly decreases for a moment, and then recovers. This can be seen clearly by comparing it to Target Common Rail Pressure.

Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.1Kd-Ftv Engine Control System.Ecd System. Dtc P0093 Fuel System Leak Detected - Large Leak

HINT:
*2: Injection Feedback Val #3 is 5.0 mm3/st which is large (the normal value is between -3.0 and 3.0 mm3/st) and indicates that the injector of cylinder 3 may be malfunctioning.

Reference Values for DTC P0093 Storage Point (Point A)
Data List
Value
Unit
Engine Speed
1478
rpm
Fuel Press
8900
kPa
Target Common Rail Pressure
65320
kPa
Injection Volume (Point A)
51.26*1
mm3/st
Injection Volume (Point A`)
9.76
mm3/st
Accel Position
63.67
%
Injection Feedback Val #1
-1.1
mm3/st
Injection Feedback Val #2
-2.5
mm3/st
Injection Feedback Val #3
5.0
mm3/st
Injection Feedback Val #4
-1.8
mm3/st
MIL
ON
-
1.CHECK FOR FUEL LEAKS (IN HIGH-PRESSURE AREAS)

  1. Before starting the engine, visually check for fuel leaks from the fuel supply pump, fuel injectors, common rail, and the fuel pipes in high-pressure areas.

    OK:
    No fuel leaks in high-pressure areas.


NG
REPAIR FUEL LEAK POINT
OK


2.CHECK FOR ANY OTHER DTC OUTPUT (PROCEDURE 2) (IN ADDITION TO DTC P0093 AND RECORD STORED DTC AND FREEZE FRAME DATA)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs and freeze frame data.

    Result:
    Display (DTC Output)
    		Proceed to
    P0093 and "P0190, P0192 and/or P0193"
    		C
    P0093 and "P0335 and/or P0339"
    		B
    Except above
    		A


B
GO TO CRANKSHAFT POSITION SENSOR "A" CIRCUIT (Toyota Fortuner RM0000012WS006X.html)

C
GO TO FUEL RAIL PRESSURE SENSOR CIRCUIT (Toyota Fortuner RM00000188003EX.html)
A


3.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)

  1. Check if the fuel level is low.

    Result:
    Result
    		Proceed to
    The indicator (fuel warning light) is illuminated
    		A
    The indicator (fuel warning light) is not illuminated
    		B


B
Go to step 6
A


4.ADD FUEL

  1. Add fuel.


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50

  1. Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

    NOTICE:
    1. Hand pump pumping speed: Max. 2 strokes/sec.
    2. The hand pump must be pushed with a full stroke during pumping.
    3. When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
    4. If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
    5. If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
    6. If a large amount of air remains inside the fuel system, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.

  1. Start the engine.

    NOTICE:
    1. If a large amount of air remains inside the fuel system, the starter may need to be cranked for 10 seconds or more to start the engine.
    2. Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
    3. Use a fully-charged battery.

    1. When the engine can be started, proceed to the next step.

    2. If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases. Then start the engine.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Clear DTCs (Toyota Fortuner RM0000012WY00LX.html).

  1. Start the engine. (*A)

  1. Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak. (*B)

  1. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak. (*C)



  1. Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time. (*D)


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.1Kd-Ftv Engine Control System.Ecd System. Dtc P0093 Fuel System Leak Detected - Large Leak

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read Current DTCs.

    1. When no DTCs are output, the air bleeding is completed.

    2. If any DTCs are output, proceed to the next step.

  1. Repeat steps (*A) to (*D).

  1. Clear DTCs (Toyota Fortuner RM0000012WY00LX.html).

  1. Start the engine and warm it up.

  1. Confirm that the shift lever is in neutral and securely apply the parking brake.

  1. Fully depress the accelerator pedal for 5 seconds, and then release it. (*E)

  1. Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*F)



  1. Repeat procedures (*E) and (*F) 5 times.


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.1Kd-Ftv Engine Control System.Ecd System. Dtc P0093 Fuel System Leak Detected - Large Leak

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read Current DTCs.

    Result:
    Display (DTC Output)
    		Proceed to
    DTC output
    		A
    DTC not output
    		B


B
DTC CAUSED BY RUNNING OUT OF FUEL
A


6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VAL #1 TO #4)

  1. Read the value of Injection Feedback Val #1 to #4 in the Freeze Frame Data recorded in Procedure 2.

    Result:

    Result
    		Proceed to
    Injection Feedback Val for at least one cylinder is 5 mm3/st in at least 1 set of freeze frame data
    		B
    Except above
    		A
    HINT:
    When there is a problem with the operation of a fuel injector due to foreign matter in the inside of the fuel injector, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.


B
Go to step 10
A


7.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear the DTCs (Toyota Fortuner RM0000012WY00LX.html).

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

  1. Start the engine.

  1. Read the value of Fuel Press while cranking and idling the engine.

    Result
    Result
    		Proceed to
    The engine cannot be started or the engine can be started but Fuel Press is less than 20000 kPa 2 seconds after the starter signal changes from OFF to ON.
    		B
    Except above
    		A


B
Go to step 15
A


8.READ VALUE USING INTELLIGENT TESTER (INJECTION FEEDBACK VAL #1 TO #4)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Start the engine and warm it up.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #4.

  1. Read the values.

    Standard:

    Tester Display
    		Engine Condition*
    		Normal Value
    Injection Feedback Val #1
    Injection Feedback Val #2
    Injection Feedback Val #3
    Injection Feedback Val #4
    		Idling
    		 -3.0 mm3/st to 3.0 mm3/st
    HINT:
    *: The A/C switch and all accessory switches should be off, the engine coolant temperature should be 70°C (158°F) or more and the engine should be idled for 1 minute or more.

    Result
    Result
    		Proceed to
    Injection Feedback Val for at least one cylinder is more than 3 mm3/st and engine vibration is abnormally large
    		B
    Except above
    		A
    HINT:
    1. When there is a problem with the operation of a fuel injector due to foreign matter in the inside of fuel injector, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.
    2. The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st (-3.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the fuel injectors are not malfunctioning.


B
Go to step 10
A


9.PERFORM ENGINE SPEED ACCELERATION

  1. Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.

  1. Stop the vehicle and allow the engine to idle.

  1. While checking the tachometer, fully depress the accelerator pedal for 5 seconds, and then release it.*1

  1. Repeat procedure *1 5 times.

    Result
    Result
    		Proceed to
    No problems such as sluggishness or variations in the tachometer reading
    		A
    Except above
    		B


B
Go to step 18
A


Go to step 11

10.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER

  1. Clean the fuel filter case and replace the fuel filter.

    HINT:
    Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.

NEXT


11.BLEED AIR FROM FUEL SYSTEM

  1. Bleed the air from the fuel system (Toyota Fortuner RM0000014FK006X_01_0002.html).


NEXT


12.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure, and Target Pump SCV Current.



    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.1Kd-Ftv Engine Control System.Ecd System. Dtc P0093 Fuel System Leak Detected - Large Leak

  1. Take a snapshot with the intelligent tester during the Active Test.

    HINT:
    Detailed graphs can be displayed by transferring the stored snapshot from the tester to a PC (personal computer) with Intelligent Viewer installed.


  1. Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.

    HINT:
    In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.

    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.1Kd-Ftv Engine Control System.Ecd System. Dtc P0093 Fuel System Leak Detected - Large Leak

    OK:
    The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.
    HINT:
    1. "Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.
    2. "Fuel Press" is the actual fuel pressure.

    Result
    Result
    		Proceed to
    The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.
    		A
    Except above
    		B


B
Go to step 15
A


13.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)
HINT:
Use this Active Test to determine the malfunctioning cylinder.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.

    HINT:
    1. If the engine idle speed does not change when a fuel injector is disabled, the cylinder being tested is malfunctioning. Record any malfunctioning cylinders.
    2. If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.

NEXT


14.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER

  1. Replace the fuel injector of the malfunctioning cylinder (Toyota Fortuner RM000002SY100QX.html).



NEXT
Go to step 16

15.REPLACE FUEL INJECTORS OF ALL CYLINDERS

  1. Replace the fuel injectors (Toyota Fortuner RM000002SY100QX.html).


NEXT


16.BLEED AIR FROM FUEL SYSTEM

  1. Bleed the air from the fuel system (Toyota Fortuner RM0000014FK006X_01_0002.html).


NEXT


17.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING

  1. Register the injector compensation code (Toyota Fortuner RM0000012XK030X_02_0003.html).

  1. Perform the fuel injector pilot quantity learning (Toyota Fortuner RM0000012XK030X_02_0009.html).



NEXT
Go to step 28

18.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

  1. Read the value while cranking and idling the engine.

    Standard:
    Tester Display
    		Engine Condition
    		Specified Condition
    Engine Speed
    		Cranking
    		50 to 400 rpm
    Idling with warm engine
    		700 to 800 rpm
    HINT:
    The value should be the same as the actual engine speed and displayed with no interruption on the tester.


NG
Go to step 22
OK


19.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.1Kd-Ftv Engine Control System.Ecd System. Dtc P0093 Fuel System Leak Detected - Large Leak

  1. Connect the positive (+) probe of an oscilloscope to the fuel pressure sensor input terminal of the ECM connector and the negative (-) probe to the body ground.

  1. Turn the ignition switch to ON.



  1. Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.1Kd-Ftv Engine Control System.Ecd System. Dtc P0093 Fuel System Leak Detected - Large Leak


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.1Kd-Ftv Engine Control System.Ecd System. Dtc P0093 Fuel System Leak Detected - Large Leak

    Standard voltage:
    Tester Connection
    		Condition
    		Specified Condition
    E7-26 (PCR1) - Body ground
    		Vibration is applied to the wire harness and connectors
    		No noise in the waveform

    Result:

    Result
    		Proceed to
    MIL comes on or noise present in the waveform
    		B
    Except above
    		A


B
Go to step 23
A


20.INSPECT FUEL TEMPERATURE SENSOR (SENSOR OUTPUT)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Fuel Temperature.

  1. Read the value.

    OK:
    The value is almost the same as the actual fuel temperature.
    HINT:
    1. When the engine is stopped and left overnight, the fuel temperature becomes the same as the atmospheric temperature.
    2. If there is a problem with the fuel temperature sensor, and a fuel temperature value lower than the actual fuel temperature is indicated, P0093 may be detected.


NG
Go to step 27
OK


21.CHECK FOR INTERMITTENT PROBLEMS

  1. Check for intermittent problems (Toyota Fortuner RM0000012X400LX.html).



NEXT
Go to step 28

22.REPLACE CRANKSHAFT POSITION SENSOR

  1. Replace the crankshaft position sensor.

    HINT:
    Before replacing the crankshaft position sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.


NEXT
Go to step 28

23.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - FUEL PRESSURE SENSOR)

  1. Repair or replace the harness or connector.


NEXT


24.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.1Kd-Ftv Engine Control System.Ecd System. Dtc P0093 Fuel System Leak Detected - Large Leak

  1. Connect the positive (+) probe of an oscilloscope to the fuel pressure sensor input terminal of the ECM connector and the negative (-) probe to the body ground.

  1. Turn the ignition switch to ON.

  1. Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.

    Standard voltage:
    Tester Connection
    		Condition
    		Specified Condition
    E7-26 (PCR1) - Body ground
    		Vibration is applied to the wire harness and connectors
    		No noise in the waveform

    Result:

    Result
    		Proceed to
    MIL comes on or noise present in the waveform
    		A
    Except above
    		B


B
Go to step 28
A


25.REPLACE COMMON RAIL ASSEMBLY

  1. Replace the common rail assembly (Toyota Fortuner RM000002SY500QX.html).

    HINT:
    Before replacing the common rail assembly, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.

NEXT


26.BLEED AIR FROM FUEL SYSTEM

  1. Bleed the air from the fuel system (Toyota Fortuner RM0000014FK006X_01_0002.html).



NEXT
Go to step 28

27.REPLACE FUEL TEMPERATURE SENSOR

  1. Replace the fuel temperature sensor.

    HINT:
    Before replacing the fuel temperature sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.

NEXT


28.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Clear DTCs (Toyota Fortuner RM0000012WY00LX.html).

  1. Start the engine.

  1. Warm up the engine (engine coolant temperature is 70°C (158°F) or higher).

  1. Confirm that the shift lever is in neutral and securely apply the parking brake.

  1. Fully depress the accelerator pedal for 5 seconds, and then release it. (*A)

  1. Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*B)



  1. Repeat procedures (*A) and (*B) 5 times.


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.1Kd-Ftv Engine Control System.Ecd System. Dtc P0093 Fuel System Leak Detected - Large Leak

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    OK:
    No DTCs are output.

NEXT

END