DTC U0073/94 Control Module Communication Bus OFF
DTC U0124/95 Lost Communication with Lateral Acceleration Sensor Module
Inspection procedure
Refer to CAN communication system
LHD:
How to proceed with troubleshooting
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
NOTICE:
- DTCs for the CAN communication system are as follows: U0073, U0100, U0101, U0114/38, U0122, U0123, U0124, U0126, U0129, U0130, U0132, U0140, U0151, U0155, U0164, U0199, U0208, U0327, U1002 (CAN MS BUS), U1002 (CAN No. 2 BUS), U1100, U1110, U1111, U1115, U1117, U1126, B1499, B2621, B2624, B2779 and C1AEF.
- Refer to the troubleshooting procedures of each system if DTCs regarding the CAN communication system are not output.
- Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected .
HINT:
- Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
- *: Use the intelligent tester.
| 1.VEHICLE BROUGHT TO WORKSHOP |
| NEXT | |
| 2.INSPECT BATTERY VOLTAGE |
Standard voltage:
11 to 14 V
-
If the voltage is below 11 V, recharge or replace the battery before proceeding.
| NEXT | |
| 3.CHECK AND CLEAR DTC* |
-
Using the intelligent tester, perform the all DTCs check.
NOTICE:
- If there is a CAN communication trouble code that indicates that an ECU or sensor has a power malfunction or interior malfunction which is causing a communication stop, the problem may not be in the communication line. There is a high possibility that the ECU or sensor has a signal transmission failure. Therefore, first troubleshoot any DTCs related to the ECU or sensor.
- When CAN communication related connectors are disconnected with the ignition switch ON or ACC, the ECU related to the connector and ECUs of related systems will store a CAN communication DTC.
| NEXT | |
| 4.CHECK INSTALLED SYSTEMS (ECU AND SENSOR) THAT USE CAN COMMUNICATION |
-
Based on the vehicle equipment and specifications, confirm the systems that use CAN communication .
| NEXT | |
| 5.CHECK DLC3 BRANCH WIRE AND V BUS CIRCUIT MAIN WIRE (CANH - CANL) |
-
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected .
-
Measure the resistance of the DLC3.
Standard Resistance:
Tester Connection Switch Condition Specified Condition Proceed to 6 (CANH) - 14 (CANL) Ignition switch off OK (54 to 69 ?) A 6 (CANH) - 14 (CANL) Ignition switch off NG (70 ? or higher) B 6 (CANH) - 14 (CANL) Ignition switch off NG (Below 54 ?) C Text in Illustration *1 DLC3
|
|
||||
|
|
| A | |
| 6.CHECK V BUS CIRCUIT +B (CANH, CANL - BAT) |
-
Connect the cable to the negative (-) battery terminal.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected .
-
Measure the resistance of the DLC3.
Standard Resistance:
Tester Connection Switch Condition Specified Condition 6 (CANH) - 16 (BAT) Ignition switch off 6 k? or higher 14 (CANL) - 16 (BAT) Ignition switch off 6 k? or higher Text in Illustration *1 DLC3
|
|
| OK | |
| 7.CHECK V BUS CIRCUIT GND (CANH, CANL - CG) |
-
Measure the resistance of the DLC3.
Standard Resistance:
Tester Connection Switch Condition Specified Condition 6 (CANH) - 4 (CG) Ignition switch off 200 ? or higher 14 (CANL) - 4 (CG) Ignition switch off 200 ? or higher Text in Illustration *1 DLC3
|
|
| OK | |
| 8.CHECK ECUS CONNECTED TO CAN BUS* |
NOTICE:
The ECUs and sensors that are not present will not be displayed. Be careful not to mistake them for communication stop malfunctions.
HINT:
-
Select "Bus Check" from "System Select".
-
Wait 1 minute and then check the display of the connected ECUs and sensors.
Result Result Proceed to All ECUs and sensors connected to the CAN communication system are displayed on the screen. A Except for the main body ECU (cowl side junction block LH), no ECUs connected to the MS bus are displayed. The main body ECU (cowl side junction block LH) outputs the MS bus trouble code (U1002) (MS bus main wire open or short malfunction). B No ECUs connected to the MS bus are displayed (the branch wire between the main body ECU (cowl side junction block LH) and V bus circuit is open). C Except for the network gateway ECU, no ECUs connected to the movement control bus are displayed.* The network gateway ECU outputs the movement control bus trouble code (U1002) (movement control bus main wire open or short malfunction). D No ECUs connected to the movement control bus are displayed (the branch wire between the network gateway ECU and movement control bus is open).* E An ECU or sensor that should be connected to the CAN communication system is not displayed (the ECU or sensor branch wire is open). F An ECU or sensor that should be connected to the CAN communication system is not displayed or display is intermittent during check (the ECU or sensor branch wire is open on one side). G - *: w/ Network Gateway ECU
- If the display of an ECU is intermittent during the check, one side of an ECU or sensor branch wire is open (The signal of the ECU is treated as noise, which affects the response and display of the intelligent tester).
- The main body ECU (cowl side junction block LH) checks for proper ECU communication for ECUs that are connected to the CAN MS bus circuit, and the results are displayed on the intelligent tester.
- The gateway ECU built into the main body ECU (cowl side junction block LH) may be malfunctioning if both of the following occurs: 1) all ECUs connected to the MS bus are not displayed on the tester; and 2) DTC U1002 is not output.
- If communication stops between an ECU and the main body ECU (cowl side junction block LH) or network gateway ECU for 10 seconds or more, the ECU disappears from the intelligent tester display.
- For communication stop mode of ECUs connected to the CAN MS bus circuit or movement control bus, refer to the DTC flowchart of the respective communication stop.
|
|
||||
|
|
||||
|
|
||||
|
|
||||
|
|
||||
|
|
| A | |
| 9.CHECK COMMUNICATION MALFUNCTION DTC (PAST DTC CHECK)* |
-
Select "Bus Check" from "System Select".
-
Write down all of the DTCs stored in each ECU.
HINT:
- If there are communication malfunction DTCs stored but the intelligent tester "Bus Check - Communication Bus Check" screen displays all of the ECUs and sensors connected to the CAN system, the communication malfunction DTCs may be past malfunctions that are no longer present.
- For V bus main wire malfunctions, related ECUs are also detected. Therefore, determine the malfunctioning area based on all of the DTCs that are output.
- For MS bus malfunctions, DTCs are stored based on the detection of communication stop malfunctions and network malfunctions of ECUs that are connected by the main body ECU (cowl side junction block LH).
- For movement control bus malfunctions, DTCs are stored based on the detection of communication stop malfunctions and network malfunctions of ECUs that are connected by the network gateway ECU.
Result Result Proceed to An ECU connected to the V bus main wire has stored a communication trouble code (V bus main wire past malfunction). A The main body ECU (cowl side junction block LH) outputs the MS bus trouble code (U1002) (MS bus past malfunction). B The main body ECU (cowl side junction block LH) outputs a trouble code other than MS bus trouble code (U1002) (past malfunction of ECU branch wire connected to MS bus). C The network gateway ECU outputs a movement control bus trouble code (U1002) (movement control bus past malfunction).* D The network gateway ECU outputs a trouble code other than movement control bus trouble code (U1002) (past malfunction of branch wire connected to movement control bus).* E - *: w/ Network Gateway ECU
|
|
||||
|
|
||||
|
|
||||
|
|
| A | |
| 10.CHECK DTC COMBINATION TABLE (V BUS CIRCUIT BRANCH WIRE OPEN PAST MALFUNCTION) |
-
Based on the combination of stored CAN communication system DTCs, determine which ECUs and sensors have a communication stop malfunction .
| NEXT | |
| 11.PERFORM MALFUNCTION SIMULATION TEST (V BUS CIRCUIT MAIN WIRE PAST MALFUNCTION)* |
-
Using the intelligent tester, clear all DTCs.
-
Perform a malfunction simulation test on all harnesses and connectors related to the V bus circuit main wire.
-
Check the DTCs that were stored as a result of the malfunction simulation test. Then determine the malfunctioning area.
| NEXT | |
| 12.ADJUST, REPAIR AND REPLACE |
| NEXT | |
| 13.CONFIRMATION TEST |
| NEXT | |
| END |
RHD:
How to proceed with troubleshooting
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
NOTICE:
- DTCs for the CAN communication system are as follows: U0073, U0100, U0101, U0114/38, U0122, U0123, U0124, U0126, U0129, U130, U0132, U0140, U0151, U0155, U0164, U0199, U0208, U0327, U1002 (CAN MS BUS), U1002 (CAN No. 2 BUS), U1100, U1110, U111, U1115, U1126, B1499, B2621, B2624, C1AEF.
- Refer to the troubleshooting procedures of each system if DTCs regarding the CAN communication system are not output.
- Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected .
HINT:
- Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
- *: Use the intelligent tester.
| 1.VEHICLE BROUGHT TO WORKSHOP |
| NEXT | |
| 2.INSPECT BATTERY VOLTAGE |
Standard Voltage:
11 to 14 V
-
If the voltage is below 11 V, recharge or replace the battery before proceeding.
| NEXT | |
| 3.CHECK AND CLEAR DTC* |
-
Using the intelligent tester, perform the all DTCs check.
NOTICE:
- If there is a CAN communication trouble code that indicates that an ECU or sensor has a power malfunction or interior malfunction which is causing a communication stop, the problem may not be in the communication line. There is a high possibility that the ECU or sensor has a signal transmission failure. Therefore, first troubleshoot any DTCs related to the ECU or sensor.
- When CAN communication related connectors are disconnected with the ignition switch ON or ACC, the ECU related to the connector and ECUs of related systems will store a CAN communication DTC.
| NEXT | |
| 4.CHECK INSTALLED SYSTEMS (ECU AND SENSOR) THAT USE CAN COMMUNICATION |
-
Based on the vehicle equipment and specifications, confirm the systems that use CAN communication .
| NEXT | |
| 5.CHECK DLC3 BRANCH WIRE AND V BUS CIRCUIT MAIN WIRE (CANH - CANL) |
-
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected .
-
Measure the resistance of the DLC3.
Standard Resistance:
Tester Connection Switch Condition Specified Condition Proceed to 6 (CANH) - 14 (CANL) Ignition switch off OK (54 to 69 ?) A 6 (CANH) - 14 (CANL) Ignition switch off NG (70 ? or higher) B 6 (CANH) - 14 (CANL) Ignition switch off NG (Below 54 ?) C Text in Illustration *1 DLC3
|
|
||||
|
|
| A | |
| 6.CHECK V BUS CIRCUIT +B (CANH, CANL - BAT) |
-
Connect the cable to the negative (-) battery terminal.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected .
-
Measure the resistance of the DLC3.
Standard Resistance:
Tester Connection Switch Condition Specified Condition 6 (CANH) - 16 (BAT) Ignition switch off 6 k? or higher 14 (CANL) - 16 (BAT) Ignition switch off 6 k? or higher Text in Illustration *1 DLC3
|
|
| OK | |
| 7.CHECK V BUS CIRCUIT GND (CANH, CANL - CG) |
-
Measure the resistance of the DLC3.
Standard Resistance:
Tester Connection Switch Condition Specified Condition 6 (CANH) - 4 (CG) Ignition switch off 200 ? or higher 14 (CANL) - 4 (CG) Ignition switch off 200 ? or higher Text in Illustration *1 DLC3
|
|
| OK | |
| 8.CHECK ECUS CONNECTED TO CAN BUS* |
NOTICE:
The ECUs and sensors that are not present will not be displayed. Be careful not to mistake them for communication stop malfunctions.
HINT:
-
Select "Bus Check" from "System Select".
-
Wait 1 minute and then check the display of the connected ECUs and sensors.
Result Inspection Result Proceed to All ECUs and sensors connected to the CAN communication system are displayed on the screen. A Except for the main body ECU (cowl side junction block LH), no ECUs connected to the MS bus are displayed. The main body ECU (cowl side junction block LH) outputs the MS bus trouble code (U1002) (the MS bus main wire open or short malfunction). B No ECUs connected to the MS bus are displayed (the branch wire between the main body ECU (cowl side junction block LH) and V bus circuit is open). C Except for the network gateway ECU, no ECUs connected to the movement control bus are displayed. The network gateway ECU outputs the movement control bus trouble code (U1002) (the movement control bus main wire open or short malfunction). D No ECUs connected to the movement control bus are displayed (the branch wire between the network gateway ECU and movement control bus is open). E An ECU or sensor that should be connected to the CAN communication system is not displayed (the ECU or sensor branch wire is open). F An ECU or sensor that should be connected to the CAN communication system is not displayed or display is intermittent during check (the ECU or sensor branch wire is open on one side). G - If the display of an ECU is intermittent during the check, one side of an ECU or sensor branch wire is open (The signal of the ECU is treated as noise, which affects the response and display of the intelligent tester).
- The main body ECU (cowl side junction block LH) checks for proper ECU communication for ECUs that are connected to the CAN MS bus circuit, and the results are displayed on the intelligent tester.
- The gateway ECU built into the main body ECU (cowl side junction block LH) may be malfunctioning if both of the following occurs: 1) all ECUs connected to the MS bus are not displayed on the tester; and 2) DTC U1002 is not output.
- If communication stops between an ECU and the main body ECU (cowl side junction block LH) or network gateway ECU for 10 seconds or more, the ECU disappears from the intelligent tester display.
- For communication stop mode of ECUs connected to the CAN MS bus circuit or movement control bus, refer to the DTC flowchart of the respective communication stop.
|
|
||||
|
|
||||
|
|
||||
|
|
||||
|
|
||||
|
|
| A | |
| 9.CHECK COMMUNICATION MALFUNCTION DTC (PAST DTC CHECK)* |
-
Select "Bus Check" from "System Select".
-
Write down all of the DTCs stored in each ECU.
HINT:
- If there are communication malfunction DTCs stored but the intelligent tester "Bus Check - Communication Bus Check" screen displays all of the ECUs and sensors connected to the CAN system, the communication malfunction DTCs may be past malfunctions that are no longer present.
- For V bus main wire malfunctions, related ECUs are also detected. Therefore, determine the malfunctioning area based on all of the DTCs that are output.
- For MS bus malfunctions, DTCs are stored based on the detection of communication stop malfunctions and network malfunctions of ECUs that are connected by the main body ECU (cowl side junction block LH).
- For movement control bus malfunctions, DTCs are stored based on the detection of communication stop malfunctions and network malfunctions of ECUs that are connected by the network gateway ECU.
Result Inspection Result Proceed to An ECU connected to the V bus main wire has stored a communication trouble code (V bus main wire past malfunction). A The main body ECU (cowl side junction block LH) outputs the MS bus trouble code (U1002) (MS bus past malfunction). B The main body ECU (cowl side junction block LH) outputs a trouble code other than MS bus trouble code (U1002) (past malfunction of ECU branch wire connected to MS bus). C The network gateway ECU outputs a movement control bus trouble code (U1002) (movement control bus past malfunction). D The network gateway ECU outputs a trouble code other than movement control bus trouble code (U1002) (past malfunction of branch wire connected to movement control bus). E
|
|
||||
|
|
||||
|
|
||||
|
|
| A | |
| 10.CHECK DTC COMBINATION TABLE (V BUS CIRCUIT BRANCH WIRE OPEN PAST MALFUNCTION) |
-
Based on the combination of stored CAN communication system DTCs, determine which ECUs and sensors have a communication stop malfunction .
| NEXT | |
| 11.PERFORM MALFUNCTION SIMULATION TEST (V BUS CIRCUIT MAIN WIRE PAST MALFUNCTION)* |
-
Using the intelligent tester, clear all DTCs.
-
Perform a malfunction simulation test on all harnesses and connectors related to the V bus circuit main wire.
-
Check the DTCs that were stored as a result of the malfunction simulation test. Then determine the malfunctioning area.
| NEXT | |
| 12.ADJUST, REPAIR AND REPLACE |
| NEXT | |
| 13.CONFIRMATION TEST |
| NEXT | |
| END |