Audio Visual Telematics. Land Cruiser. Urj200, 202 Grj200 Vdj200
Park Assist Monitoring. Land Cruiser. Urj200, 202 Grj200 Vdj200
Blind Spot Monitor System -- Data List / Active Test |
| DATA LIST |
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
- HINT:
- Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Data List.
Read the Data List according to the display on the GTS.
Blind spot monitor Master Tester Display Measurement Item/Range Normal Condition Diagnostic Note Main Switch State of the blind spot monitor main switch (steering pad switch assembly [multi-function switch]) / OFF or ON OFF: Blind spot monitor main switch (steering pad switch assembly [multi-function switch]) off
ON: Blind spot monitor main switch (steering pad switch assembly [multi-function switch]) on- RCTA Switch Status State of RCTA function / OFF or ON OFF: RCTA function off
ON: RCTA function onw/ RCTA Warning Indicator Turning on (Master) State of the outer rear view mirror indicator LH turning on / OFF or ON OFF: Any state except "ON" - ON: Either of the following states
- During initial check
- Blind spot monitor system on, vehicle detected on left hand side and left turn signal switch not on
- Warning Indicator Flashing (Master) State of the outer rear view mirror indicator LH flashing / OFF or ON OFF: Any state except "ON
ON: Blind spot monitor system on, vehicle detected on left hand side and left turn signal switch on- Warning Indicator Input Circuit Voltage Outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V Indicator illuminated: 2.5 to 7.5 V
Indicator not illuminated: Below 1 V- Warning Indicator Input Circuit Current Outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA Indicator illuminated: 5 to 100 mA
Indicator not illuminated: 0 mA- Turn Switch State State of the headlight dimmer switch assembly (turn signal light switch) / Left ON, Right ON or OFF Left ON: Left side of turn signal light switch on
Right ON: Right side of turn signal light switch on
OFF: Turn signal light switch off- Reverse (Only for AT/CVT) State of the shift position R signal / OFF or ON OFF: Shift lever in any position except R
ON: Shift lever in R- Vehicle Speed Vehicle speed signal / Min.: -327.68 km/h (-204 mph), Max.: 327.67 km/h (204 mph) Vehicle stopped: 0 km/h (0 mph) - Steering Angle Steering angle sensor / Min.: -3072 deg, Max.: 3070.5 deg Left turn: Increases
Right turn: Decreases- VGRS Relative Angle Compensation value of steering angle calculated by VGRS / Min.: -8.192 rad, Max.: 8.191 rad Left turn: Increases
Right turn: Decreases- Power Supply Voltage Power supply voltage / Min.: 0 V, Max.: 49.951 V Engine switch on (IG): 11 to 14 V - Indicator Light Control State Outer rear view mirror indicator dimming state / Dim OFF or Dim ON Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed- HV Flag Hybrid vehicle / OFF or ON OFF: Non-hybrid vehicle
ON: Hybrid vehicle- VGRS Flag VGRS installed / OFF or ON OFF: VGRS not installed
ON: VGRS installed- Main SW Inspection Completeness Flag Completion of inspection for blind spot monitor main switch (steering pad switch assembly [multi-function switch]) / Incompl or Compl Incompl: Inspection not completed
Compl: Inspection completed- Beam Axis Inspection Completeness Flag Completion of beam axis adjustment / Incompl or Compl Incompl: Adjustment not completed
Compl: Adjustment completedChanges to "Compl" when blind spot monitor beam axis adjustment has been finished Destination Undefined Flag Destination determination / Unfixed or Fixed Unfixed: Sensor destination information not determined
Fixed: Sensor destination information determined according to CAN destination information- Angle Adjustment by Auto Alignment Angle adjusted using auto alignment / Min.: Under -180 deg, Max.: Over 180 deg Angle adjusted using auto alignment is displayed - RCTA Equipped Information State of the RCTA equipped information / OFF or ON OFF: RCTA function off
ON: RCTA function onw/ RCTA Master Side RCTA Function Switches the RCTA function on and off / OFF or ON OFF: RCTA function off
ON: RCTA function onw/ RCTA Mirror LED Control Frequency Frequency of the outer rear view mirror indicator on the outer mirror when blinki / Min.: 1500 Hz, Max.: 2400 Hz Always: 2000 Hz - Setting of Warning Indicator Current (Dim OFF) Set current of the outer rear view mirror indicator when not dimmed / Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA - Setting of Warning Indicator Current (Dim ON) Set current of the outer rear view mirror indicator when dimmed / Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA - Mirror LED Duty Ratio (Blinking) Duty ratio of the outer rear view mirror indicator when blinking / Min.: 0%, Max.: 100% Always: 50 % - Yaw Rate Sensor Yaw rate sensor / Min.: Under -125 deg/s, Max.: 124.612 deg/s Turning right: -125 to 0 deg/s
Turning left: 0 to 124.612 deg/s- Master Side BSM Approaching Vehicle Detection Timing Setting Notification timing for vehicles approaching from behind the vehicle / Only Blind Spot, Late, Middle or Early Only Blind Spot: Only detection area (for vehicle in blind spot) is active
Late: Late notification
Middle: Default notification timing
Early: Early notification- BSM Mirror Indicator Brightness Brightness of the indicators in the outer rear view mirror assemblies / Dark or Bright Dark: Outer rear view mirror indicator dark
Bright: Outer rear view mirror indicator bright- Number of DTC Number of DTC / Min.: 0, Max.: 255 When system is normal: 0
When a malfunction is detected: More than 0- Blind spot monitor Slave Tester Display Measurement Item/Range Normal Condition Diagnostic Note Warning Indicator Turning on (Slave) State of the outer rear view mirror indicator RH turning on / OFF or ON OFF: Any state except "ON" - ON: Either of the following states
- During initial check
- Blind spot monitor system on, vehicle detected on right hand side and right turn signal switch not on
- Warning Indicator Flashing (Slave) State of the outer rear view mirror indicator RH flashing / OFF or ON OFF: Any state except "ON"
ON: Blind spot monitor system on, vehicle detected on right hand side and right turn signal switch on- Buzzer Sound Status State of the RCTA buzzer (blind spot monitor buzzer) / OFF or ON OFF: Buzzer not sounding
ON: Buzzer soundingw/ RCTA Warning Indicator Input Circuit Voltage Outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V Indicator illuminated: 2.5 to 7.5 V
Indicator not illuminated: Below 1 V- Warning Indicator Input Circuit Current Outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA Indicator illuminated: 5 to 100 mA
Indicator not illuminated: 0 mA- Buzzer Input Circuit Voltage RCTA buzzer (blind spot monitor buzzer) voltage / Min.: 0 V, Max.: 25.5 V Buzzer not sounding: 11 to 14 V
Buzzer sounding: Alternating between 0 to 14 Vw/ RCTA Turn Switch State State of the headlight dimmer switch assembly (turn signal light switch) / Left ON, Right ON or OFF Left ON: Left side of turn signal light switch on
Right ON: Right side of turn signal light switch on
OFF: Turn signal light switch off- Reverse (Only for AT/CVT) State of the shift position R signal / OFF or ON OFF: Shift lever in any position except R
ON: Shift lever in R- Reverse (Only for MT) State of the shift position R signal / OFF or ON* OFF: Shift lever in any position except R
ON: Shift lever in RNot applicable Vehicle Speed Vehicle speed signal / Min.: -327.68 km/h (-204 mph), Max.: 327.67 km/h (204 mph) Vehicle stopped: 0 km/h (0 mph) - Steering Angle Steering angle sensor / Min.: -3072 deg, Max.: 3070.5 deg Left turn: Increases
Right turn: Decreases- VGRS Relative Angle Compensation value of steering angle calculated by VGRS / Min.: -8.192 rad, Max.: 8.191 rad Left turn: Increases
Right turn: Decreases- Power Supply Voltage Power supply voltage / Min.: 0 V, Max.: 49.951 V Engine switch on (IG): 11 to 14 V - Indicator Light Control State Outer rear view mirror indicator dimming state / Dim OFF or Dim ON Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed- HV Flag Hybrid vehicle / OFF or ON OFF: Non-hybrid vehicle
ON: Hybrid vehicle- VGRS Flag VGRS installed / OFF or ON OFF: VGRS not installed
ON: VGRS installed- Beam Axis Inspection Completeness Flag Completion of beam axis adjustment / Incompl or Compl Incompl: Adjustment not completed
Compl: Adjustment completedChanges to "Compl" when blind spot monitor beam axis adjustment has been finished Destination Undefined Flag Destination determination / Unfixed or Fixed Unfixed: Sensor destination information not determined
Fixed: Sensor destination information determined according to CAN destination information- Angle Adjustment by Auto Alignment Angle adjusted using auto alignment / Min.: Under -180 deg, Max.: Over 180 deg Angle adjusted using auto alignment is displayed - RCTA Equipped Information Status of the RCTA equipped information / ON or OFF ON: RCTA function on
OFF: RCTA function offw/ RCTA Slave Side RCTA Function Switches the RCTA function on and off / OFF or ON ON: RCTA function on
OFF: RCTA function offw/ RCTA Mirror LED Control Frequency Frequency of the outer rear view mirror indicator on the outer mirror when blinking / Min.: 1500 Hz, Max.: 2400 Hz Always: 2000 Hz - Setting of Warning Indicator Current (Dim OFF) Set current of the outer rear view mirror indicator when not dimmed / Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA - Setting of Warning Indicator Current (Dim ON) Set current of the outer rear view mirror indicator when dimmed / Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA - Mirror LED Duty Ratio (Blinking) Duty ratio of the outer rear view mirror indicator when blinking / Min.: 0%, Max.: 100% Always: 50 % - Buzzer Control Frequency Frequency of the RCTA buzzer (blind spot monitor buzzer) when sounding / Min.: 1000 Hz, Max.: 2400 Hz Always: 2000 Hz - Yaw Rate Sensor Yaw rate sensor / Min.: Under -125 deg/s, Max.: 124.612 deg/s Turning right: -125 to 0 deg/s
Turning left: 0 to 124.612 deg/s- BSM Buzzer Volume Adjust Status of the RCTA buzzer (blind spot monitor buzzer) volume adjust / Low, Medium or High Low:
Medium:
High:- Slave Side BSM Approaching Vehicle Detection Timing Setting Notification timing for vehicles approaching from behind the vehicle / Only Blind Spot, Late, Middle or Early Only Blind Spot: Only detection area (for vehicle in blind spot) is active
Late: Late notification
Middle: Default notification timing
Early: Early notification- Number of DTC Number of DTC / Min.: 0, Max.: 255 When system is normal: 0
When a malfunction is detected: More than 0- - *: Although the item is displayed on the GTS, it is not applicable to this vehicle.
- ON: Either of the following states