Washer Nozzle (For Front Side) Installation
INSTALL WASHER NOZZLE SUB-ASSEMBLY (w/ PTC Heater)
INSTALL WASHER NOZZLE SUB-ASSEMBLY (w/o PTC Heater)
INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
INSTALL HOOD TO COWL TOP SEAL
INSTALL FRONT FENDER MAIN SEAL LH
INSTALL FRONT FENDER MAIN SEAL RH
INSTALL UPPER RADIATOR SUPPORT SEAL
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
Washer Nozzle (For Front Side) -- Installation |
- HINT:
- Use the same procedure for the LH and RH sides.
- The procedure listed below is for the LH side.
| 1. INSTALL WASHER NOZZLE SUB-ASSEMBLY (w/ PTC Heater) |
Connect the hose.
Attach the 4 claws to install the washer nozzle.
Connect the connector and attach the connector clamp.
| 2. INSTALL WASHER NOZZLE SUB-ASSEMBLY (w/o PTC Heater) |
Attach the 3 clamps to install the washer nozzle.
Connect the hose.
| 3. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
Attach the 17 claws and 2 clips and install the cowl top ventilator louver sub-assembly.
| 4. INSTALL HOOD TO COWL TOP SEAL |
Attach the 12 clips and 4 clamps to install the hood to cowl top seal.
Install the washer hose.
| 5. INSTALL FRONT FENDER MAIN SEAL LH |
Attach the 3 clips and 2 guides to install the front fender main seal LH.
| 6. INSTALL FRONT FENDER MAIN SEAL RH |
- HINT:
- Use the same procedure described for the LH side.
| 7. INSTALL UPPER RADIATOR SUPPORT SEAL |
Install the upper radiator support seal with the 7 clips.
| 8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 9. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
Stop the wiper motor at the automatic stop position.
Text in Illustration*a
| Wiper Arm Serrations
|
*b
| Wiper Pivot Serrations
|
Clean the wiper arm serration with a round file or equivalent.
Clean the wiper pivot serration.
Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade comes to the position shown in the illustration.
Text in Illustration*a
| Moulding Edge
|
- Standard Measurement:
Position
| Specified Condition
|
A
| 16.8 to 36.8 mm (0.661 to 1.45 in.)
|
- Torque:
- 25 N*m{255 kgf*cm, 18 ft.*lbf}
- HINT:
- Hold down the wiper arm hinge with your hand while tightening the nut.
| 10. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
Stop the wiper motor at the automatic stop position.
Text in Illustration*a
| Wiper Arm Serrations
|
*b
| Wiper Pivot Serrations
|
Clean the wiper arm serration with a round file or equivalent.
Clean the wiper pivot serration.
Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade comes to the position shown in the illustration.
Text in Illustration*a
| Moulding Edge
|
- Standard Measurement:
Position
| Specified Condition
|
A
| 20.0 to 40.0 mm (0.787 to 1.57 in.)
|
- Torque:
- 25 N*m{255 kgf*cm, 18 ft.*lbf}
- HINT:
- Hold down the wiper arm hinge with your hand while tightening the nut.
Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.
