INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)
INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)
Front Seat Outer Belt Assembly (For Hatchback 3 Door) -- Installation |
- CAUTION:
- Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (YARIS_NCP93 RM000000KT10EAX.html).
- HINT:
- The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.
| 1. INSTALL FRONT SEAT OUTER BELT ASSEMBLY |
Check the angle of inclination required to lock the retractor.
Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15 ° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45 ° or more.
Text in Illustration *a Unlock *b Lock - NOTICE:
- Do not disassemble the retractor.
 |
Engage the 2 hooks and temporarily install the front seat outer belt assembly with the 2 bolts.
 |
Tighten bolt A and then bolt B.
- Torque:
- 4.9 N*m{50 kgf*cm, 43 in.*lbf}for bolt A
- 41 N*m{420 kgf*cm, 30 ft.*lbf}for bolt B
Connect the pretensioner connector.
Text in Illustration *1 Locking Button
 |
Lock the locking button.
- NOTICE:
- Securely lock the locking button.
Install the shoulder anchor with the bolt.
- Torque:
- 41 N*m{420 kgf*cm, 30 ft.*lbf}
Install the floor anchor with the bolt.
- Torque:
- 41 N*m{420 kgf*cm, 30 ft.*lbf}
Check that the ELR locks.
- NOTICE:
- The check should be performed with the front seat outer belt installed.
- Do not allow the anchor part of the front seat outer belt and the protruding parts of the floor panel to overlap.
With the belt installed, check that the belt locks when it is pulled out quickly.
If the operation is not as specified, replace the front seat outer belt assembly.
Remove the bolt and the floor anchor.
| 2. INSTALL CENTER PILLAR UPPER GARNISH |
Pass the front seat outer belt through the slit in the center pillar upper garnish.
Engage the clip and install the center pillar upper garnish with 2 screws.
| 3. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY |
Engage the 8 clips and the 10 claws.
Engage the 3 guides and install the quarter trim panel.
| 4. CONNECT FRONT SEAT OUTER BELT ASSEMBLY |
Install the floor anchor part of the front seat outer belt assembly with the bolt.
- Torque:
- 41 N*m{420 kgf*cm, 30 ft.*lbf}
Engage the 3 claws and install the lap belt outer anchor cover.
| 5. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP |
Align the paint mark on the front door opening trim weatherstrip with the flange position on the vehicle body and install the weatherstrip.
Text in Illustration *a Paint Mark *b Flange Position - Paint Mark:
Area Color RH Side Yellow LH Side White
- NOTICE:
- After installation, check that the corners fit correctly.
 |
| 6. INSTALL FRONT DOOR SCUFF PLATE |
Engage the 8 claws and install the front door scuff plate.
| 7. INSTALL REAR SEAT ASSEMBLY (for Fold Down Seat Type) |
| 8. INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side) |
| 9. INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side) |
| 10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{55 kgf*cm, 48 in.*lbf}
| 11. INSPECT SRS WARNING LIGHT |