Can Communication System (For Rhd Without Entry And Start System) Open In Can Main Wire


DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CHECK FOR OPEN IN CAN BUS BRANCH WIRE (NO. 2 JUNCTION CONNECTOR - DLC3)

CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - ECM)

CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

CONNECT CONNECTOR

CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - ECM)

CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

CONNECT CONNECTOR

CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 3 JUNCTION CONNECTOR)

CONNECT CONNECTOR

CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 3 JUNCTION CONNECTOR)

CONNECT CONNECTOR

CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

CONNECT CONNECTOR

CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY - NO. 1 JUNCTION CONNECTOR)

CAN COMMUNICATION SYSTEM (for RHD without Entry and Start System) - Open in CAN Main Wire


DESCRIPTION

There may be an open circuit in the CAN main wire and/or DLC3 CAN branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.

Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
  1. CAN main wire and connector
  2. ECM
  3. Combination meter assembly
  4. No. 1 junction connector
  5. No. 2 junction connector
  6. No. 3 junction connector
  7. DLC3 CAN branch wire or connector

WIRING DIAGRAM


Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Networking.Lin Communication System.Can Communication System (For Rhd Without Entry And Start System) Open In Can Main Wire


INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.
    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (LandCruiser RM000003YMD00TX.html).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (LandCruiser RM000003YMF011X.html).

NEXT


2.CHECK FOR OPEN IN CAN BUS BRANCH WIRE (NO. 2 JUNCTION CONNECTOR - DLC3)


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Networking.Lin Communication System.Can Communication System (For Rhd Without Entry And Start System) Open In Can Main Wire

  1. Disconnect the G132 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    G132-4 (CANH) - G48-6 (CANH)
    		Ignition switch off
    		Below 1 Ω
    G132-15 (CANL) - G48-14 (CANL)
    		Ignition switch off
    		Below 1 Ω
    Text in Illustration
    *a
    		Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    		Front view of DLC3


NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - ECM)


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Networking.Lin Communication System.Can Communication System (For Rhd Without Entry And Start System) Open In Can Main Wire

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    G132-1 (CANH) - G132-12 (CANL)
    		Ignition switch off
    		108 to 132 Ω
    Text in Illustration
    *a
    		Rear view of wire harness connector
    (to No. 2 Junction Connector)


NG
Go to step 5
OK


4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Networking.Lin Communication System.Can Communication System (For Rhd Without Entry And Start System) Open In Can Main Wire

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    G132-8 (CANH) - G132-19 (CANL)
    		Ignition switch off
    		108 to 132 Ω
    Text in Illustration
    *a
    		Rear view of wire harness connector
    (to No. 2 Junction Connector)


NG
Go to step 12
OK

REPLACE NO. 2 JUNCTION CONNECTOR

5.CONNECT CONNECTOR

  1. Reconnect the G132 No. 2 junction connector.


NEXT


6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - ECM)


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Networking.Lin Communication System.Can Communication System (For Rhd Without Entry And Start System) Open In Can Main Wire

  1. Disconnect the G134 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    G134-2 (CANH) - G134-13 (CANL)
    		Ignition switch off
    		108 to 132 Ω
    Text in Illustration
    *a
    		Rear view of wire harness connector
    (to No. 3 Junction Connector)
    Result
    Result
    		Proceed to
    OK
    		A
    NG (for 1KD-FTV)
    		B
    NG (for 5L-E)
    		C


B
Go to step 8

C
Go to step 10
A


7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Networking.Lin Communication System.Can Communication System (For Rhd Without Entry And Start System) Open In Can Main Wire

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    G134-1 (CANH) - G134-12 (CANL)
    		Ignition switch off
    		108 to 132 Ω
    Text in Illustration
    *a
    		Rear view of wire harness connector
    (to No. 3 Junction Connector)


NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK

REPLACE NO. 3 JUNCTION CONNECTOR

8.CONNECT CONNECTOR

  1. Reconnect the G134 No. 3 junction connector.


NEXT


9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 3 JUNCTION CONNECTOR)


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Networking.Lin Communication System.Can Communication System (For Rhd Without Entry And Start System) Open In Can Main Wire

  1. Disconnect the G58 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    G58-35 (CANH) - G58-36 (CANL)
    		Ignition switch off
    		108 to 132 Ω
    Text in Illustration
    *a
    		Front view of wire harness connector
    (to ECM)


NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 3 JUNCTION CONNECTOR)
OK

REPLACE ECM (LandCruiser RM0000013Z002CX.html)

10.CONNECT CONNECTOR

  1. Reconnect the G134 No. 3 junction connector.


NEXT


11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 3 JUNCTION CONNECTOR)


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Networking.Lin Communication System.Can Communication System (For Rhd Without Entry And Start System) Open In Can Main Wire

  1. Disconnect the G183 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    G183-25 (CANH) - G183- 31 (CANL)
    		Ignition switch off
    		108 to 132 Ω
    Text in Illustration
    *a
    		Front view of wire harness connector
    (to ECM)


NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 3 JUNCTION CONNECTOR)
OK

REPLACE ECM (LandCruiser RM000000VW203FX.html)

12.CONNECT CONNECTOR

  1. Reconnect the G132 No. 2 junction connector.


NEXT


13.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Networking.Lin Communication System.Can Communication System (For Rhd Without Entry And Start System) Open In Can Main Wire

  1. Disconnect the A72 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    A72-10 (CANH) - A72-21 (CANL)
    		Ignition switch off
    		108 to 132 Ω
    Text in Illustration
    *a
    		Rear view of wire harness connector
    (to No. 1 Junction Connector)


NG
Go to step 15
OK


14.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Networking.Lin Communication System.Can Communication System (For Rhd Without Entry And Start System) Open In Can Main Wire

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    A72-9 (CANH) - A72-20 (CANL)
    		Ignition switch off
    		108 to 132 Ω
    Text in Illustration
    *a
    		Rear view of wire harness connector
    (to No. 1 Junction Connector)


NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK

REPLACE NO. 1 JUNCTION CONNECTOR

15.CONNECT CONNECTOR

  1. Reconnect the A72 No. 1 junction connector.


NEXT


16.CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY - NO. 1 JUNCTION CONNECTOR)


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Networking.Lin Communication System.Can Communication System (For Rhd Without Entry And Start System) Open In Can Main Wire

  1. Disconnect the G6 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    G6-40 (CANH) - G6-39 (CANL)
    		Ignition switch off
    		108 to 132 Ω
    Text in Illustration
    *a
    		Front view of wire harness connector
    (to Combination Meter Assembly)


NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (COMBINATION METER ASSEMBLY - NO. 1 JUNCTION CONNECTOR)
OK

REPLACE COMBINATION METER ASSEMBLY (LandCruiser RM000003QKY01CX.html)