Combination Meter Removal


  1. DISABLE AUTOAWAY/RETURN FUNCTION (for Power Tilt and Power Telescopic Steering Column)

  2. PRECAUTION

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  4. REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT (for LHD)

  5. REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH (for RHD)

  6. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

  7. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

  8. REMOVE COMBINATION METER ASSEMBLY

Combination Meter -- Removal


HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. DISABLE AUTOAWAY/RETURN FUNCTION (for Power Tilt and Power Telescopic Steering Column)

  1. Disable the Autoaway/Return function by changing the customize parameter (LandCruiser RM000004KI4013X.html).

    NOTICE:
    Record the current customize parameter setting (whether the Autoaway/Return function is enabled or disabled) in order to restore the current setting after finishing the operation.
    HINT:
    Performing the above operation causes the Autoaway/Return function to be disabled when the ignition switch is turned off.

  1. Turn the ignition switch to ON. Operate the tilt and telescopic switch to fully extend and lower the steering column.

  1. Turn the ignition switch off.



2. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (LandCruiser RM000003YMD00TX.html).


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (LandCruiser RM000003YMF011X.html).


4. REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT (for LHD)


Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Meter Gauge Display.Meter / Gauge System.Combination Meter Removal

  1. Put protective tape around the instrument cluster finish panel ornament.

    Text in Illustration
    *1
    		Protective Tape

  1. Using a moulding remover, detach the 3 clips and remove the instrument cluster finish panel ornament.



5. REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH (for RHD)


Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Detach the 4 clips.

  1. Disconnect each connector and remove the instrument panel finish plate garnish.



6. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Detach the 4 clips.

  1. Disconnect each connector and remove the instrument panel finish panel.



7. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Meter Gauge Display.Meter / Gauge System.Combination Meter Removal

  1. Place protective tape as shown in the illustration.

    Text in Illustration
    *1
    		Protective Tape

  1. Detach the 4 claws.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Detach the 4 claws.

  1. Detach the 2 clips and 2 guides.

  1. Disconnect the connector and remove the instrument cluster finish panel sub-assembly.



8. REMOVE COMBINATION METER ASSEMBLY


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Remove the 4 screws and combination meter assembly.

  1. Disconnect the 2 connectors.