Ecd System Engine Difficult To Start Or Stalling

DESCRIPTION

INSPECTION PROCEDURE

CHECK ENGINE CRANKING CONDITION

READ ALL OUTPUT DTCS

TAKE SNAPSHOT DURING STARTING AND IDLING (PROCEDURE 3)

CHECK SNAPSHOT (COMMON RAIL PRESSURE)

CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP ASSEMBLY

CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)

REPLACE FUEL SUPPLY PUMP ASSEMBLY (PRE-STROKE CONTROL VALVE)

BLEED AIR FROM FUEL SYSTEM

READ VALUE USING GTS (COMMON RAIL PRESSURE)

INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)

CHECK AND REPAIR OR REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP)

BLEED AIR FROM FUEL SYSTEM

READ VALUE USING GTS (COMMON RAIL PRESSURE)

REPLACE FUEL SUPPLY PUMP ASSEMBLY (PRE-STROKE CONTROL VALVE)

REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

READ VALUE USING GTS (INJECTOR FEEDBACK VAL #1 TO #4 AND INJECTION VOLUME)

REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)

CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER

REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

REPLACE FUEL FILTER ELEMENT ASSEMBLY

BLEED AIR FROM FUEL SYSTEM

REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING

CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

INSPECT INJECTOR POWER SOURCE CIRCUIT

INSPECT INJECTOR ASSEMBLY

CHECK TEMPERATURE WHEN STARTING TROUBLE OCCURS

READ VALUE USING GTS (COOLANT TEMP)

INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

CHECK FUEL QUALITY

READ OUTPUT DTC (RELATED TO ENGINE)

CHECK COMMUNICATION BETWEEN GTS AND ECM

READ VALUE USING GTS (STARTER SIGNAL AND NEUTRAL POSITION SW SIGNAL)

CHECK STARTING SYSTEM

CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

ECD SYSTEM - Engine Difficult to Start or Stalling

DESCRIPTION

Faults and Symptoms of Common Rail Diesel Components

1. Engine Control
   
   

   Mass Air Flow Meter

   Main fault		Decrease in performance (foreign matter is stuck)
   Symptoms		Lack of power, black smoke
   Data List		MAF
   HINT: The maximum fuel injection volume is controlled according to the output from the mass air flow meter.

   
   

   Intake System

   Symptom and Corresponding Main Fault		Lack of power (no black smoke) due to air filter blockage or crushed or leaking air duct Black smoke (no lack of power) due to leakage between the turbo and intake manifold
   Data List		MAP

   
   

   Turbocharger System

   Main fault		Air leak in the turbocharged air passage ECM not operating well Turbocharger (turbine, bearing)
   Symptoms		Lack of power (when vehicle is starting, under heavy load) (Black smoke is not emitted when racing while vehicle is stopped)
   Data List		MAP With the engine switch on (IG) or during idling, MAP = atmospheric pressure (standard atmospheric pressure = 101 kPa). When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and MAP becomes higher than atmospheric pressure. Atmospheric pressure decreases by 1 kPa each time elevation increases by 100 m, and is also affected by the current weather conditions.

   
   

   Exhaust System

   Main fault		Blockage
   Symptoms		Lack of power (high engine speed, under heavy load)

   
   

   Glow System

   Main fault		Glow system malfunction
   Symptoms		Difficult to start, rough idle, knocking, white smoke (when cold)
   Data List		Check the glow plug indicator light
   Diagnostic Point		Measure the resistance of the glow plug

   
   

   Battery

   Main fault		Battery is depleted
   Symptoms		Difficult to start (cannot crank, crank speed is low), horn is quiet
   Data List		Battery Voltage When cranking, battery voltage is below 5 V.

   
   

   Engine - 1

   Main fault		Damaged, seized up
   Symptoms		Cannot crank, crank speed is low, strange noise

   
   

   Engine - 2

   Main fault		Loss of compression
   Symptoms		Rough idle (lack of power always)
   Data List		Engine Speed of Cyl When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression. Injection Feedback Val When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder.

   
   

   Start System

   Main fault		Starter system malfunction
   Symptoms		Difficult to start
   Data List		Starter Signal Engine switch (STA) output: ON: Starter is operating OFF: Starter is not operating

2. Diesel Injection
   
   

   Fuel Supply Pump Assembly

   Main fault		-
   Symptoms		Difficult to start, engine stalling, rough idle, lack of power
   Data List		Common Rail Pressure, Target Common Rail Pressure Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)). If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt. If the fuel pressure is below 25000 kPa, then idling will be rough. HINT: The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.
   Diagnostic Trouble Code		Even if Common Rail Pressure is below Target Common Rail Pressure, a DTC will not be stored.

   
   

   Fuel filter element assembly

   Main fault		Blockage
   Symptoms		Difficult to start, engine stalling, rough idle, lack of power
   Data List		Common Rail Pressure, Target Common Rail Pressure Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)). If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt. If the fuel pressure is below 25000 kPa, then idling will be rough. HINT: The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.
   Diagnostic Trouble Code		Even if Common Rail Pressure is below Target Common Rail Pressure, a DTC will not be stored.

   
   

   Injector Assembly

   Main fault		Blockage
   Symptoms		Rough idle, lack of power, black smoke, white smoke, knocking
   Data List		Injection Feedback Val When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute.

   
   

   Pressure Discharge Valve

   Main fault		Does not completely close
   Symptoms		Difficult to start, engine stall, rough idle, lack of power

   
   

   Fuel Pressure Sensor

   Main fault		Open circuit, decrease in performance (foreign matter is stuck)
   Symptoms		Difficult to start, rough idle, engine stall, lack of power
   Data List		Common Rail Pressure, Target Common Rail Pressure Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped and check that Common Rail Pressure follows Target Common Rail Pressure. If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure (either Common Rail Pressure decreases to a value less than Target Common Rail Pressure).
   Diagnostic Trouble Code		When the fuel pressure sensor has a fault, some DTCs may be stored.

   
   

   Irregular Fuel

   Main fault		-
   Symptoms		Difficult to start, rough idle (especially when cold)

3. Diesel EGR
   
   

   EGR System

   Main fault		Does not move smoothly Does not close completely
   Symptoms		Rough idle EGR valve stuck closed: A loud turbocharger sound. EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power (if there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt).
   Data List		Actual EGR Valve Pos., Target EGR Valve Pos Generally, Actual EGR Valve Pos. = Target EGR Valve Pos +/-5% (fully closed: 0%, fully open: 100%). Using the EGR valve Active Test, check whether Actual EGR Valve Pos. follows Target EGR Valve Pos (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs). EGR valve is fully closed when the engine switch is turned to on (IG) (engine stopped). EGR valve opens to the halfway point at idling after the engine is warmed up. EGR Close Lrn. Val., When leaving the vehicle idling the normal range of EGR Close Lrn. Val. is 0 to 1 V. In cases EGR Close Lrn. Val. is out of the normal range (0 to 1 V), it is possible that the EGR valve cannot completely close.

4. Diesel Throttle
   
   

   Diesel Throttle System

   Main fault		Stuck, does not move smoothly
   Symptoms		Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed. Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.
   Data List		Actual Throttle Position 0%: Fully closed 100%: Fully open When the engine switch on (IG) (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the engine switch is turned from on (IG) to off, the throttle is fully closed temporarily.

Data List Related to Starting Trouble

1. MAP
   
2. MAF
   
3. Intake Air
   
4. Coolant Temp
   
5. Battery Voltage
   
6. Starter Signal
   
7. Engine Speed of Cyl #1 (to #4)
   (Output only when the "Check the Cylinder Compression" Active Test is performed)
   
8. Target Common Rail Pressure
   
9. Common Rail Pressure
   
10. Injection Feedback Val #1 (to #4)
    
11. Injection Volume
    
12. Actual Throttle Position
    
13. Target EGR Valve Pos
    
14. Actual EGR Valve Pos.
    
15. EGR Close Lrn. Val.
    

INSPECTION PROCEDURE

Explanation of Symptom

Starting Trouble

For good starting it is essential to have: Sufficient cranking speed. Properly operating engine preheating system. Good quality fuel. The fuel is ignited by the heat which is generated by compression pressure. With problems such as a depleted battery, the crankshaft speed can become low, or if the engine compression is poor due to leakage, the compression pressure will not rise and there will be difficulty starting. When the engine is cold, even if there is compression heat, it will escape from the combustion chamber. For this reason, when the engine is started when it is cold, the glow plugs heat the compressed air. Also, after starting the engine, by charging the glow plugs for a fixed time set according to the engine coolant temperature, diesel knocking and white smoke are prevented. The quantity of fuel injected is determined by the fuel pressure and also the amount of time the injector assembly is open.

Trouble Area Chart According to Problem Cause

NOTICE:

1. After replacing the ECM, the new ECM needs registration (LandCruiser RM0000012XK0AVX.html) and initialization (LandCruiser RM000000TIN08IX.html).
   
2. After replacing an injector assembly, the ECM needs registration (LandCruiser RM0000012XK0AVX.html).
   

HINT:

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle age. Do not assume the vehicle is normal when the Data List outputs standard values. There may be concealed factors of the malfunction.

1.CHECK ENGINE CRANKING CONDITION

1. Check the engine cranking condition.
   
   

   Result

   Result	Proceed to
   Cranking is OK.	A
   Low cranking speed. HINT: When cranking speed is low, especially when the temperature is low, check if the engine oil grade matches the recommendation.	B
   Does not crank at all.	C

B	CHECK BATTERY CONDITION (LandCruiser RM000001AR90CCX_01_0001.html)
C	Go to step 31

A

2.READ ALL OUTPUT DTCS

1. Connect the GTS to the DLC3.
   

2. Turn the engine switch on (IG) and turn the GTS on.
   

3. Enter the following menus: System Select / Health Check.
   

4. Check the DTCs.
   
   

   Result

   Result	Proceed to
   No DTC is output	A
   Engine related DTCs are output	B

   HINT:

   If only DTC P1604 is output, proceed to step 3.

B	GO TO RELATED DTC (LandCruiser RM0000031HW07PX.html)

A

3.TAKE SNAPSHOT DURING STARTING AND IDLING (PROCEDURE 3)

1. Connect the GTS to the DLC3.
   

2. Turn the engine switch on (IG) and turn the GTS on.
   

3. Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Starting.
   

4. Take a snapshot when idling with no load after the engine is warmed up and when starting trouble is occurring.
   

   HINT:

   1. A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.
      
   2. When there is trouble starting with a cold engine, take the snapshot when the engine is cold. Then warm up the engine (engine coolant temperature is 75°C (167°F) or higher) and after idling the vehicle for 1 minute (A/C off, electrical load off), take a snapshot of the data for 15 seconds while idling.
      
   3. Take a snapshot when the problem is occurring, such as when the engine is cold. However, if the problem does not reoccur, it is acceptable to only take a snapshot after the engine is warmed up and when the engine is started.
      

NEXT

4.CHECK SNAPSHOT (COMMON RAIL PRESSURE)

1. Check Common Rail Pressure in the snapshot taken in procedure 3 when the engine was started.
   

   
   
   
   
   

   Result

   Result	Proceed to
   At the point in the illustration labeled "a", Common Rail Pressure is less than 10000 kPa from the value of Common Rail Pressure when cranking started	A
   At the point in the illustration labeled "c", Common Rail Pressure is below Target Common Rail Pressure by 15000 kPa or more	B
   Common Rail Pressure increases to a value that is higher than Target Common Rail Pressure immediately after cranking, and, at the point in the illustration labeled "d", Common Rail Pressure is higher than Target Common Rail Pressure	C
   Except above	D

   HINT:

   1. Even if Common Rail Pressure is temporarily higher than Target Common Rail Pressure, as shown at the point in the illustration labeled "b", the fuel supply pump is normal.
      
   2. Fuel pressure is about 25000 to 35000 kPa when the engine is cranking and the engine coolant temperature is 0°C (32°F) or higher.
      
   3. Fuel pressure increases rapidly during cranking.
      

B	Go to step 13
C	Go to step 25
D	Go to step 16

A

5.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP ASSEMBLY

1. Disconnect the inlet hose from the fuel supply pump assembly.
   

2. Operate the priming pump and check that fuel is being supplied to the fuel supply pump assembly.
   

   OK:

   Fuel is properly supplied to the fuel supply pump assembly when the priming pump is operated.
   

   HINT:

   1. When there is a lack of fuel, fuel pressure drops.
      
   2. Inspect for fuel filter clogging (check that the fuel filter is not clogged).
      

3. Reconnect the inlet hose.
   

NG	Go to step 11

OK

6.CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)

1. Disconnect the pre-stroke control valve connector.
   

2. Disconnect the ECM connector.
   

3. Measure the resistance according to the value(s) in the table below.
   
   

   Standard Resistance:

   
   

   Tester Connection	Condition	Specified Condition
   r6-1 - C150-3 (PCV+)	Always	Below 1 Ω
   r6-2 - C150-4 (PCV-)	Always	Below 1 Ω
   r6-1 or C150-3 (PCV+) - Body ground and other terminals	Always	10 kΩ or higher
   r6-2 (PCV) or C150-4 (PCV-) - Body ground and other terminals	Always	10 kΩ or higher

4. Reconnect the pre-stroke control valve connector.
   

5. Reconnect the ECM connector.
   

NG	REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

7.REPLACE FUEL SUPPLY PUMP ASSEMBLY (PRE-STROKE CONTROL VALVE)

1. Replace the fuel supply pump assembly (LandCruiser RM000005UHX000X.html).
   

NEXT

8.BLEED AIR FROM FUEL SYSTEM

1. Bleed the air from the fuel system (LandCruiser RM000002SY803FX_01_0002.html).
   

NEXT

9.READ VALUE USING GTS (COMMON RAIL PRESSURE)

1. Connect the GTS to the DLC3.
   

2. Turn the engine switch on (IG) and turn the GTS on.
   

3. Enter the following menus: Powertrain / Engine and ECT / Data List / Common Rail Pressure.
   

4. Start the engine.
   

5. Read the values while cranking and idling the engine.
   
   

   Result

   Result	Proceed to
   The engine cannot be started or the engine can be started but Common Rail Pressure is below 20000 kPa 2 seconds after the starter signal changes from OFF to ON	B
   Except above	A

B	Go to step 10

A
END

10.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)

1. Remove the glow plug assembly for all the cylinders (LandCruiser RM000005UHS000X.html).
   

2. Visually check if there is fuel on the glow plugs.
   

   HINT:

   1. If there is fuel on a glow plug, fuel may be leaking from an injector assembly.
      
   2. After replacing an injector assembly, make sure that the common rail pressure (fuel pressure) is within 5000 kPa of the target fuel pressure while cranking the engine.
      
   3. If there is fuel on a glow plug, fuel may have mixed with the engine oil. Check the engine oil amount and whether the engine oil smells of diesel fuel. If the oil level is above the full line or the engine oil smells of diesel fuel, replace the engine oil.
      

3. Install the glow plug assembly (LandCruiser RM000005UHP000X.html).
   

NEXT	Go to step 20

11.CHECK AND REPAIR OR REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP)

1. Check and repair or replace the clogged fuel pipe.
   

NEXT

12.BLEED AIR FROM FUEL SYSTEM

1. Bleed the air from the fuel system (LandCruiser RM000002SY803FX.html).
   

NEXT	Go to step 24

13.READ VALUE USING GTS (COMMON RAIL PRESSURE)

1. Check Common Rail Pressure in the snapshot taken in procedure 3 when the engine was warmed up.
   
   

   Result

   Result	Proceed to
   Difference between Common Rail Pressure and Target Common Rail Pressure is 5000 kPa (51.0 kgf/cm2, 725 psi) or more	A
   Except above	B

B	Go to step 15

A

14.REPLACE FUEL SUPPLY PUMP ASSEMBLY (PRE-STROKE CONTROL VALVE)

1. Replace the fuel supply pump assembly (LandCruiser RM000005UHX000X.html).
   

NEXT

15.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

1. Replace the injector assemblies of all cylinders (LandCruiser RM000005UHS000X.html).
   

   NOTICE:

   1. When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.
      
   2. Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
      
   3. If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
      
   4. If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
      
   5. If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.
      

NEXT	Go to step 21

16.READ VALUE USING GTS (INJECTOR FEEDBACK VAL #1 TO #4 AND INJECTION VOLUME)

1. Check Injection Feedback Val # in the snapshot taken in procedure 3 when the engine was idling.
   
   

   Result

   Result	Proceed to
   Injection Feedback Val #1 to #4 are 3 mm3/st or less. Injection Volume is more than 16 mm3/st.	A*
   Injection Feedback Val for at least one cylinder is more than +3 mm3/st HINT: There may be a malfunction in the corresponding cylinder.	B
   Except above	C

   HINT:

   1. *: When this case occurs, usually symptoms may be noticeable, such as difficulty starting, lack of power.
      
   2. The shift lever should be in neutral and the A/C switch and all accessory switches should be off.
      

B	Go to step 18
C	Go to step 27

A

17.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

1. Replace the injector assemblies of all cylinders (LandCruiser RM000005UHS000X.html).
   

   NOTICE:

   1. When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.
      
   2. Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
      
   3. If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
      
   4. If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
      
   5. If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.
      

NEXT	Go to step 21

18.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)

HINT:

Use this Active Test to help determine whether a cylinder has compression loss or not.

1. Connect the GTS to the DLC3.
   

2. Start the engine and turn the GTS on.
   

3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.
   

4. Check the engine speed during the Active Test.
   
   

   Result

   Result	Proceed to
   Except below	A
   The values of Engine Speed Cyl #1 to #4 are within +/-10 rpm of each other.	B

   HINT:

   When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.

B	Go to step 20

A

19.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER

HINT:

Measure the compression of the cylinder that had a high speed during the "Check the Cylinder Compression" Active Test.

1. Check the cylinder compression pressure (LandCruiser RM000005UTQ000X_02_0009.html).
   

NG	CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

OK

20.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

HINT:

It can be determined that the injector assembly is faulty as the corresponding cylinder is malfunctioning, but has no compression loss.

1. Replace the injector assembly of malfunctioning cylinder (LandCruiser RM000005UHS000X.html).
   

   NOTICE:

   1. When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.
      
   2. Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
      
   3. If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
      
   4. If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
      
   5. If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.
      

NEXT

21.REPLACE FUEL FILTER ELEMENT ASSEMBLY

1. Replace the fuel filter element assembly (LandCruiser RM0000045HW008X.html).
   

NEXT

22.BLEED AIR FROM FUEL SYSTEM

1. Bleed the air from the fuel system (LandCruiser RM000002SY803FX_01_0002.html).
   

NEXT

23.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING

1. Register the injector compensation codes (LandCruiser RM0000012XK0AVX_02_0003.html).
   

2. Perform the injector pilot quantity learning (LandCruiser RM0000012XK0AVX_02_0009.html).
   

NEXT

24.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT
END

25.INSPECT INJECTOR POWER SOURCE CIRCUIT

1. Perform troubleshooting for DTC P062D during a startability malfunction, even if DTC P062D is not output (LandCruiser RM00000187V09IX.html).
   When troubleshooting the injector power source circuit, check the following locations, as one may contain the cause of the malfunction
   

1. EDU relay
   
2. Injector assembly circuit
   
3. ECM
   

HINT:

1. When the engine cannot be started due to a malfunction in the injector power source circuit, once the DTCs are cleared, P062D cannot be stored even when the problem symptoms are reproduced and a startability malfunction occurs.
   Since P062D cannot be stored when starting the engine, fuel injection cannot be performed even though fuel injection signals are output from the ECM. Therefore, using the GTS during a startability malfunction to check the data shows that an excessive amount of fuel is supplied to the common rail assembly by the fuel supply pump assembly, and as a result, the Common Rail Pressure is higher than the Target Common Rail Pressure.
   
2. Perform the following procedure when a malfunction cannot be found during the troubleshooting procedure for P062D and the Common Rail Pressure when starting the engine is higher than the Target Common Rail Pressure.
   
3. Perform the troubleshooting procedure for DTC P062D and proceed to the diagnostic flow situations where the engine does not start.
   

B	REPAIR OR REPLACE MALFUNCTIONING PARTS

A

26.INSPECT INJECTOR ASSEMBLY

1. Disconnect the injector assembly connectors.
   

2. Measure the resistance of the injector assembly.
   

   OK:

   No open circuit malfunction.
   

3. Reconnect the injector assembly connectors.
   

OK	Go to step 35
NG	Go to step 20

27.CHECK TEMPERATURE WHEN STARTING TROUBLE OCCURS

1. Check the temperature when starting trouble occurs.
   

Result

Result	Proceed to
Difficult to start only for cold engine.	A
Difficult to start both for cold and warmed up engine.	B

B	Go to step 30

A

28.READ VALUE USING GTS (COOLANT TEMP)

1. Connect the GTS to the DLC3.
   

2. Turn the engine switch on (IG) and turn the GTS on.
   

3. Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Starting / Coolant Temp.
   

4. Read the value displayed on the GTS.
   

   OK:

   Coolant Temp is not high when the engine is cold, and not low after the engine is warmed up
   

NG	REPLACE ENGINE COOLANT TEMPERATURE SENSOR (LandCruiser RM0000013ZA01XX.html)

OK

29.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

1. Inspect the glow plug assembly (LandCruiser RM0000044ZK00TX_01_0001.html).
   

NG	REPLACE GLOW PLUG ASSEMBLY (LandCruiser RM000000JIT01FX.html)

OK

30.CHECK FUEL QUALITY

1. Check that only diesel fuel is being used.
   

2. Check that the fuel does not contain any impurities.
   

NEXT	Go to step 35

31.READ OUTPUT DTC (RELATED TO ENGINE)

1. Connect the GTS to the DLC3.
   

2. Turn the engine switch on (IG) and turn the GTS on.
   

3. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
   

4. Read the DTCs.
   
   

   Result

   Result	Proceed to
   No DTC is output	A
   Engine related DTCs are output	B

B	GO TO DTC

A

32.CHECK COMMUNICATION BETWEEN GTS AND ECM

1. Connect the GTS to the DLC3.
   

2. Turn the engine switch on (IG) and turn the GTS on.
   

3. Check if the normal starting screen appears (check whether communication with the ECM is possible).
   

   HINT:

   Use a GTS that is able to communicate with other vehicles.

   OK:

   Communication is possible (vehicle can be recognized).
   

NG	CHECK VC OUTPUT CIRCUIT (LandCruiser RM000001D6V0X2X.html)

OK

33.READ VALUE USING GTS (STARTER SIGNAL AND NEUTRAL POSITION SW SIGNAL)

1. Connect the GTS to the DLC3.
   

2. Turn the engine switch on (IG) and turn the GTS on.
   

3. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal and Neutral Position SW Signal.
   

4. Read the value displayed on the GTS.
   
   

   OK:

   
   

   GTS Display	Condition	Specified Condition
   Starter Signal	Cranking	ON
   Neutral Position SW Signal*	Shift lever in neutral	ON

   *: only for Automatic transmission
   
   

   Result

   Result	Proceed to
   OK	A
   NG (for Manual transmission)	B
   NG (for Automatic transmission)	C

B	INSPECT CLUTCH SWITCH ASSEMBLY (LandCruiser RM0000032S300DX.html)
C	INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (LandCruiser RM000000OD401HX.html)

A

34.CHECK STARTING SYSTEM

1. Inspect the starting system.
   

   HINT:

   Be sure to inspect the following areas:

   1. Battery
      
   2. Starter relay
      
   3. Starter assembly
      
   4. Entry and start system
      
   5. Immobiliser system
      

NEXT

35.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT
END