Ecd System (For Dpf) Fuel Injection System

INSPECTION PROCEDURE

CHECK INJECTOR COMPENSATION CODE

REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING

TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 3)

READ VALUE USING INTELLIGENT TESTER (INJECTION FEEDBACK VAL #1 TO #4 AND INJECTION VOLUME)

PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CHECK THE CYLINDER COMPRESSION)

CHECK CYLINDER COMPRESSION PRESSURE

PERFORM PILOT QUANTITY LEARNING

READ VALUE USING INTELLIGENT TESTER (INJECTION FEEDBACK VAL #1 TO #4)

REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

READ VALUE USING INTELLIGENT TESTER (INJECTION VOLUME)

REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER

BLEED AIR FROM FUEL SYSTEM

REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING

CHECK AND REPLACE ENGINE ASSEMBLY

PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK)

INSPECT COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE)

INSPECT CLOGGED FUEL PIPE

REPAIR OR REPLACE CLOGGED FUEL LINE

REPLACE COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE)

BLEED AIR FROM FUEL SYSTEM

READ VALUE USING INTELLIGENT TESTER (FUEL PRESS AND TARGET COMMON RAIL PRESSURE)

REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

BLEED AIR FROM FUEL SYSTEM

PERFORM SUPPLY PUMP INITIALIZATION

CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

INSPECTION PROCEDURE

NOTICE:

1. After replacing the ECM, the new ECM needs registration (HILUX_TGN26 RM0000012XK070X.html) and initialization (HILUX_TGN26 RM000000TIN057X.html).
   
2. After replacing the fuel supply pump assembly, the ECM needs initialization (HILUX_TGN26 RM000000TIN057X.html).
   
3. After replacing an injector assembly, the ECM needs registration (HILUX_TGN26 RM0000012XK070X.html).
   

1. Check the injector compensation code (HILUX_TGN26 RM0000012XK070X_02_0006.html).
   
   

   Result

   Result	Proceed to
   Except below	A
   Compensation codes of the installed injector assemblies are the same as the compensation codes registered in the ECM	B

1. Register the injector compensation codes (HILUX_TGN26 RM0000012XK070X_02_0003.html).
   

2. Perform the injector pilot quantity learning (HILUX_TGN26 RM0000012XK070X_02_0009.html).
   

1. Connect the intelligent tester to the DLC3.
   

2. Start the engine and turn the tester on.
   

3. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
   

4. Take a snapshot of the following Data List items.
   

   Text in Illustration

   *1	Snapshot Button
   *a	Reference

   HINT:

   1. A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the list below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.
      
   2. Graphs like the ones shown below can be displayed by transferring the stored snapshot data from the tester to a PC. Intelligent Viewer must be installed on the PC.
      
   3. Check the Data List at idling and at 4000 rpm with no load after the engine is warmed up.
      

1. Check Injection Feedback Val #1 to #4 and Injection Volume in the snapshot taken in procedure 3 when the engine was idling and at 4000 rpm with no load.
   
   

   Result

   Result	Proceed to
   Injection Feedback Val for at least one cylinder is more than 3.0 mm3/st	A
   Injection Volume is 7 mm3/st or less at 4000 rpm	B
   Except above	C

   HINT:

   1. When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.
      
   2. The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm³/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm³/st (-3.0 mm³/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm³/st or less, the injector assemblies are not malfunctioning.
      

HINT:

Use this Active Test to help determine whether a cylinder has compression loss or not.

1. Connect the intelligent tester to the DLC3.
   

2. Start the engine and turn the tester on.
   

3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.
   

4. Check the engine speed during the Active Test.
   
   

   Result

   Result	Proceed to
   Except below	A
   The values of Engine Speed Cyl #1 to #4 are within +/-10 rpm of each other.	B

   HINT:

   When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.

1. Check the cylinder compression pressure (HILUX_TGN26 RM000001473022X_01_0002.html).
   

   HINT:

   When compression is low, there may be cracks in the piston or the injector assembly may be installed improperly.

1. Perform the injector pilot quantity learning (HILUX_TGN26 RM0000012XK070X_02_0009.html).
   

1. Connect the intelligent tester to the DLC3.
   

2. Turn the ignition switch to ON and turn the tester on.
   

3. Start the engine and warm it up.
   

4. Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #4.
   

5. Read the values.
   
   

   Standard:

   
   

   Tester Display	Engine Condition*	Normal Value
   Injection Feedback Val #1 Injection Feedback Val #2 Injection Feedback Val #3 Injection Feedback Val #4	Idling	-3.0 mm3/st to 3.0 mm3/st

   HINT:

   *: The A/C switch and all accessory switches should be off, the engine coolant temperature should be 75°C (167°F) or more and the engine should be idled for 1 minute or more.

   
   

   Result

   Result	Proceed to
   Injection Feedback Val for at least one cylinder is more than 3.0 mm3/st	A
   Except above	B

   HINT:

   1. When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.
      
   2. The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm³/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm³/st (-3.0 mm³/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm³/st or less, the injector assemblies are not malfunctioning.
      

1. Replace the injector assembly of the malfunctioning cylinder (HILUX_TGN26 RM0000044TN00QX.html).
   

   NOTICE:

   1. When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
      
   2. Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
      
   3. If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
      
   4. If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
      
   5. If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.
      

1. Check Injection Volume in the snapshot taken in procedure 3 when the engine was idling.
   
   

   Result

   Result	Proceed to
   Injection Volume while idling after engine warm up is 9 mm3/st or more	A
   Except above	B

   HINT:

   Check that PM forced regeneration was not being performed.

   The idling speed during PM forced regeneration is 850 to 950 rpm (with the shift lever in neutral).

1. Replace the injector assemblies of all cylinders (HILUX_TGN26 RM0000044TN00QX.html).
   

   NOTICE:

   1. When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
      
   2. Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
      
   3. If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
      
   4. If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
      
   5. If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.
      

1. Clean the fuel filter case and replace the fuel filter.
   

   HINT:

   Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.

1. Bleed the air from the fuel system (HILUX_TGN26 RM000002SY802HX_01_0002.html).
   

1. Register the injector compensation codes (HILUX_TGN26 RM0000012XK070X_02_0003.html).
   

2. Perform the injector pilot quantity learning (HILUX_TGN26 RM0000012XK070X_02_0009.html).
   

1. Check and replace the engine assembly.
   

1. Connect the intelligent tester to the DLC3.
   

2. Turn the ignition switch to ON and turn the tester on.
   

3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure, and Target Pump SCV Current.
   

4. Start the engine.
   

5. Take a snapshot with the intelligent tester during the Active Test.
   

   Text in Illustration

   *1	Snapshot Button
   *a	Reference

   HINT:

   Detailed graphs can be displayed by transferring the stored snapshot from the tester to a PC (Personal Computer) with Intelligent Viewer installed.

6. Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.
   

   HINT:

   In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.

   
   
   
   

   OK:

   The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa (102.0 kgf/cm², 1451 psi).
   

   
   

   Result

   Result	Proceed to
   NG	A
   OK*	B

   NOTICE:

   *: Even when the results of the Active Test are normal, take a snapshot of vehicle data when the vehicle is accelerating. If "Fuel Press" does not follow "Target Common Rail Pressure", proceed to step 17.

   If "Fuel Press" does not follow "Target Common Rail Pressure", the fuel filter may be clogged.

   HINT:

   1. "Target Common Rail Pressure" means target fuel pressure controlled by the ECM.
      
   2. "Fuel Press" means actual fuel pressure in common rail assembly.
      
   3. If the pressure discharge valve mounted on the common rail assembly is malfunctioning, the actual fuel pressure may change as indicated by "Pressure Discharge Valve Malfunctioning" in the illustration.
      
   4. The pressure discharge valve operates to discharge fuel pressure when the internal pressure of the common rail exceeds the target fuel pressure.
      
   5. There are 2 fuel pressure sensor circuits and both of them display the same value. If the difference between Fuel Press and Common Rail Press Sens 2 exceeds 10000 kPa (102 kgf/cm², 1451 psi) for 2 seconds or more, it is necessary to inspect or repair the wiring for the fuel pressure sensor.
      

1. Enter the following menus: Powertrain / Engine and ECT / Utility / Pressure Discharge Valve Check (HILUX_TGN26 RM000002SY802HX_01_0003.html).
   

2. Select "Always Closed Check".
   

3. Press "Next".
   

4. Read the Value of fuel pressure values.
   

   OK:

   Fuel pressure is properly maintained.
   

   HINT:

   1. If the fuel pressure cannot be maintained, the pressure discharge valve may not have a tight seal.
      
   2. If the fuel pressure is being properly maintained, there are no problems with the sealing properties of the high-pressure fuel system. Therefore, an insufficient supply of fuel due to the fuel filter being clogged, or squashed or blocked low-pressure fuel pipes or hoses may be causing the reduction in common rail pressure.
      

1. Connect the intelligent tester to the DLC3.
   

2. Start the engine and turn the tester on.
   

3. Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Injection.
   

4. With no load after the engine is warmed up, take a snapshot when idling and vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear.
   

5. Check the Target Common Rail Pressure and Fuel Press value.
   

   
   
   
   
   

   Result

   Result	Proceed to
   While idling the vehicle, "Fuel Press" deviates from the normal range and varies periodically with a period of approximately 2 seconds or more*1	A
   "Fuel Press" is normal while idling the vehicle, but "Fuel Press" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear*2
   Except above	B

   NOTICE:

   1. *1: The cause may be a squashed or blocked fuel pipe or hose.
      
   2. *2: The cause may be a clogged fuel filter.
      

1. Repair or replace the clogged (including frozen fuel) fuel pipe.
   

2. Replace the fuel filter element sub-assembly.
   

   HINT:

   If "Fuel Press" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear, replace the fuel filter element sub-assembly.

1. Replace the common rail assembly (HILUX_TGN26 RM0000044W300QX.html).
   

1. Bleed the air from the fuel system (HILUX_TGN26 RM000002SY802HX_01_0002.html).
   

1. Check Fuel Press and Target Common Rail Pressure in the snapshot taken in procedure 3 when the engine was idling.
   
   

   Result

   Result	Proceed to
   Difference between Fuel Press and Target Common Rail Pressure is 5000 kPa (51.0 kgf/cm2, 725 psi) or more	B
   Except above	A

1. Replace the fuel supply pump assembly (HILUX_TGN26 RM0000014FO029X.html).
   

1. Bleed the air from the fuel system (HILUX_TGN26 RM000002SY802HX_01_0002.html).
   

1. Perform supply pump initialization (HILUX_TGN26 RM000000TIN057X.html).