Dtc P0560 System Voltage

Engine Hybrid System. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25
2Tr-Fe Engine Control. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25

DESCRIPTION

MONITOR STRATEGY

TYPICAL MALFUNCTION THRESHOLDS

CONFIRMATION DRIVING PATTERN

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK HARNESS AND CONNECTOR (ECM - BATTERY)

INSPECT BATTERY

CHECK BATTERY TERMINAL

CHECK WHETHER DTC OUTPUT RECURS

DTC P0560 System Voltage


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0560
Open in the ECM backup power source circuit (1 trip detection logic).
  1. Open in backup power source circuit
  2. Battery
  3. Battery terminals
  4. EFI fuse
  5. ECM
HINT:
If DTC P0560 is stored, the ECM does not store other DTCs and the data stored in the ECM is partly cleared.

MONITOR STRATEGY


Required Sensors/Components
ECM
Frequency of Operation
Continuous

TYPICAL MALFUNCTION THRESHOLDS


Stand-by RAM
Initialized
ECM power source
Below 3.5 V

CONFIRMATION DRIVING PATTERN

  1. Turn the ignition switch to ON and wait for 5 seconds or more.

WIRING DIAGRAM


Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.2Tr-Fe Engine Control.Sfi System (W/ Secondary Air Injection System). Dtc P0560 System Voltage


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
1.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)

  1. Disconnect the ECM connector.

  1. Disconnect the cable from the positive (+) battery terminal.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    		Condition
    		Specified Condition
    G89-3 (BATT) - Positive (+) battery cable terminal
    		Always
    		Below 1 Ω
    G89-3 (BATT) or Positive (+) battery cable terminal - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT BATTERY

  1. Check that the battery is not depleted (HILUX_TGN26 RM000000V4301SX_01_0001.html).

    OK:
    Battery is not depleted.


NG
REPLACE BATTERY
OK


3.CHECK BATTERY TERMINAL

  1. Check that the battery terminals are not loose or corroded.

    OK:
    Battery terminals are not loose or corroded.


NG
REPAIR BATTERY TERMINAL
OK


4.CHECK WHETHER DTC OUTPUT RECURS

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Clear the DTCs (HILUX_TGN26 RM000000PDK0X5X.html).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and turn the intelligent tester on.

  1. Wait 5 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result
    Result
    		Proceed to
    P0560 is output
    		A
    No DTC is output
    		B


B
CHECK FOR INTERMITTENT PROBLEMS (HILUX_TGN26 RM000000PDQ0TSX.html)
A

REPLACE ECM (HILUX_TGN26 RM000000VW202LX.html)