1Kd-Ftv Engine Control. Dtc P2009 Intake Manifold Runner Control Circuit Low (Bank 1)

P2009
DTC Detection Drive Pattern	DTC Detection Condition	Trouble Area
2 seconds after engine is started, race engine for 1 second	Open in vacuum switching valve (for No. 1 swirl control valve) circuit for 0.5 seconds (2 trip detection logic).	Vacuum switching valve (for No. 1 swirl control valve) Open in vacuum switching valve (for No. 1 swirl control valve) circuit ECM

P2010
DTC Detection Drive Pattern	DTC Detection Condition	Trouble Area
2 seconds after engine is started, race engine for 1 second	Short in vacuum switching valve (for No. 1 swirl control valve) circuit for 0.5 seconds (2 trip detection logic).	Vacuum switching valve (for No. 1 swirl control valve) Short in vacuum switching valve (for No. 1 swirl control valve) circuit ECM

WIRING DIAGRAM

Refer to DTC P2006 (HILUX_TGN26 RM000000YGW042X_02.html).

INSPECTION PROCEDURE

NOTICE:

After replacing the ECM, the new ECM needs registration (HILUX_TGN26 RM0000012XK07FX.html) and initialization (HILUX_TGN26 RM000000TIN04CX.html).

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)

Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.1Kd-Ftv Engine Control.Ecd System (For Dpf).
Dtc
P2009 Intake Manifold Runner Control Circuit Low (Bank 1)

Connect the intelligent tester to the DLC3.

Disconnect the vacuum hoses from the vacuum switching valve (for No. 1 swirl control valve).

Turn the ignition switch to ON and turn the tester on.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Swirl Control Valve.

Check the VSV operation when it is operated using the intelligent tester.
OK:
Tester Operation
Specified Condition
VSV ON
Air from port E flows out through port F
VSV OFF
Air from port E flows out through air filter

Reconnect the vacuum hoses.

Go to step 2

CHECK FOR INTERMITTENT PROBLEMS (HILUX_TGN26 RM000000PDQ0YSX.html)

2.INSPECT VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE (RESISTANCE)

Inspect the vacuum switching valve (for No. 1 swirl control valve) (HILUX_TGN26 RM00000143W01BX.html).

Go to step 8

OK

3.INSPECT VACUUM SWITCHING VALVE (FOR NO. 1 SWIRL CONTROL VALVE) (POWER SOURCE VOLTAGE)

Disconnect the vacuum switching valve (for No. 1 swirl control valve) connector.

Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
C61-2 - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration
*a
Front view of wire harness connector
(to Vacuum Switching Valve [for Swirl Control Valve])

Text in Illustration
*a	Front view of wire harness connector (to Vacuum Switching Valve [for Swirl Control Valve])

Go to step 6

OK

4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE [FOR SWIRL CONTROL VALVE] - ECM)

Disconnect the vacuum switching valve (for No. 1 swirl control valve) connector.

Disconnect the ECM connector.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection
Condition
Specified Condition
C61-1 - C22-15 (SCV)
Always
Below 1 Ω
C61-1 or C22-15 (SCV) - Body ground
Always
10 kΩ or higher

Reconnect the vacuum switching valve (for No. 1 swirl control valve) connector.

Reconnect the ECM connector.

Go to step 9

OK

5.REPLACE ECM

Replace the ECM (HILUX_TGN26 RM0000013Z001IX.html).

Go to step 10

6.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE [FOR SWIRL CONTROL VALVE] - NO. 1 INTEGRATION RELAY)

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

Disconnect the No. 1 integration relay connector.

Disconnect the vacuum switching valve (for No. 1 swirl control valve) connector.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection
Condition
Specified Condition
1J-5 - C61-2
Always
Below 1 Ω
1J-5 or C61-2 - Body ground
Always
10 kΩ or higher

Reinstall the No. 1 integration relay.

Reconnect the No. 1 integration relay connector.

Reconnect the vacuum switching valve (for No. 1 swirl control valve) connector.

Go to step 9

OK

7.INSPECT ECM POWER SOURCE CIRCUIT

Check the ECM power source circuit (HILUX_TGN26 RM000000TI2074X.html).

Go to step 10

8.REPLACE VACUUM SWITCHING VALVE (FOR NO. 1 SWIRL CONTROL VALVE)

Replace the vacuum switching valve (for No. 1 swirl control valve) (HILUX_TGN26 RM00000143Y02DX.html).

Go to step 10

9.REPAIR OR REPLACE HARNESS OR CONNECTOR

Repair or replace harness or connector.

NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

Connect the intelligent tester to the DLC3.

Clear the DTCs (HILUX_TGN26 RM000000PDK12RX.html).

Start the engine and wait for 3 seconds or more.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Confirm that the DTC is not output again.

END

Tester Operation	Specified Condition
VSV ON	Air from port E flows out through port F
VSV OFF	Air from port E flows out through air filter

Tester Connection	Switch Condition	Specified Condition
C61-2 - Body ground	Ignition switch ON	11 to 14 V

Tester Connection	Condition	Specified Condition
C61-1 - C22-15 (SCV)	Always	Below 1 Ω
C61-1 or C22-15 (SCV) - Body ground	Always	10 kΩ or higher