Dtc P0560 System Voltage

Engine Hybrid System. Corolla. Zre142 Aze141
2Zr-Fe Engine Control. Corolla. Zre142 Aze141

MONITOR DESCRIPTION

MONITOR STRATEGY

TYPICAL ENABLING CONDITIONS

TYPICAL MALFUNCTION THRESHOLDS

CONFIRMATION DRIVING PATTERN

WIRING DIAGRAM

INSPECTION PROCEDURE

INSPECT FUSE (EFI MAIN FUSE)

CHECK HARNESS AND CONNECTOR (ECM - EFI MAIN FUSE)

CHECK HARNESS AND CONNECTOR (BATTERY - EFI MAIN FUSE)

INSPECT BATTERY

CHECK BATTERY TERMINAL

CHECK WHETHER DTC OUTPUT RECURS

DTC P0560 System Voltage


MONITOR DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. The next time the engine is started, the ECM illuminates the MIL and sets the DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0560
Open in ECM back up power source circuit
(1 trip detection logic)
  1. Open in back up power source circuit
  2. Battery
  3. Battery terminals
  4. EFI MAIN fuse
  5. ECM
HINT:
If DTC P0560 is set, the ECM does not store other DTCs or the data stored in the ECM may be partially erased.

MONITOR STRATEGY


Related DTCs
P0560: ECM system voltage range check/rationality
Required Sensors/Components (Main)
ECM
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
3 seconds
MIL Operation
Immediate (MIL illuminated after next engine start)
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None

TYPICAL MALFUNCTION THRESHOLDS


Stand-by RAM
Initialized
Battery voltage
Less than 3.5 V

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation) (COROLLA_ZRE142 RM000000PDK0ZAX.html).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Wait 5 seconds or more.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  8. Read the pending DTCs.
    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.
  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P0560.
  11. Check the DTC judgment result.

    Techstream Display
    		Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
  12. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (COROLLA_ZRE142 RM000000PDK0ZAX.html).
    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.

WIRING DIAGRAM


Corolla. Zre142 Aze141.2Zr-Fe Engine Control.Sfi System. Dtc P0560 System Voltage


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
1.INSPECT FUSE (EFI MAIN FUSE)


    Corolla. Zre142 Aze141.2Zr-Fe Engine Control.Sfi System. Dtc P0560 System Voltage

  1. Remove the EFI MAIN fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    EFI MAIN fuse
    		Always
    		Below 1 Ω

  1. Reinstall the EFI MAIN fuse.



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


2.CHECK HARNESS AND CONNECTOR (ECM - EFI MAIN FUSE)

  1. Disconnect the negative battery terminal.

  1. Disconnect the positive battery terminal.

  1. Remove the EFI MAIN fuse from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    		Condition
    		Specified Condition
    EFI MAIN fuse (2) - A50-20 (BATT)
    		Always
    		Below 1 Ω

    Standard Resistance (Check for Short):

    Tester Connection
    		Condition
    		Specified Condition
    EFI MAIN fuse (2) or A50-20 (BATT) - Body ground
    		Always
    		10 kΩ or higher

  1. Reinstall the EFI MAIN fuse.

  1. Reconnect the ECM connector.

  1. Reconnect the positive battery terminal.

  1. Reconnect the negative battery terminal.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - EFI MAIN FUSE)
OK


3.CHECK HARNESS AND CONNECTOR (BATTERY - EFI MAIN FUSE)

  1. Disconnect the negative battery terminal.

  1. Disconnect the positive battery terminal.

  1. Remove the EFI MAIN fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    		Condition
    		Specified Condition
    Battery positive terminal - EFI MAIN fuse (1)
    		Always
    		Below 1 Ω

    Standard Resistance (Check for Short):

    Tester Connection
    		Condition
    		Specified Condition
    Battery positive terminal or EFI MAIN fuse (1) - Body ground
    		Always
    		10 kΩ or higher

  1. Reinstall the EFI MAIN fuse.

  1. Reconnect the positive battery terminal.

  1. Reconnect the negative battery terminal.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI MAIN FUSE)
OK


4.INSPECT BATTERY

  1. Check that the battery is not discharged or weak.

    OK:
    Battery is not discharged or weak


NG
CHARGE OR REPLACE BATTERY
OK


5.CHECK BATTERY TERMINAL

  1. Check that the battery terminals are not loose or corroded.

    OK:
    Battery terminals are not loose or corroded


NG
REPAIR OR REPLACE BATTERY TERMINAL
OK


6.CHECK WHETHER DTC OUTPUT RECURS

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to on.

  1. Turn the Techstream on.

  1. Clear DTCs (COROLLA_ZRE142 RM000000PDK0ZAX.html).

  1. Turn the ignition switch off and turn the Techstream off.

  1. Start the engine and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    		Proceed to
    DTC P0560 is output
    		A
    DTC is not output
    		B


B
CHECK FOR INTERMITTENT PROBLEMS (COROLLA_ZRE142 RM000000PDQ0VMX.html)
A

REPLACE ECM (COROLLA_ZRE142 RM000001CN0030X.html)