2AD-FHV Lack of Power or Hesitation

2AD-FHV problems
Lack of Power or Hesitation

Description

Malfunction Condition Main Trouble Areas Related Trouble Areas
  1. Lack of power caused by abnormal fuel injection volume (supply pump malfunction or injector malfunction)
  2. Lack of power caused by intake air volume shortage (turbocharger malfunction, front exhaust pipe or exhaust manifold converter blocked)
  1. Injector malfunctions
    1. Injector sliding malfunction
    2. Injector stuck closed
    3. Injector stuck open
    4. Deposits in injector
    5. Injector circuit malfunction
  2. Abnormal common rail pressure
    1. Supply pump
  3. Abnormal intake air volume
    1. Turbocharger
    2. Front exhaust pipe blockage
    3. Exhaust manifold converter blockage
  1. Pressure limiter
  2. Intake air system leakage
  3. Intake air system blockage
  4. EGR system
  5. Fuel filter element is clogged
  6. Throttle valve
  7. Compression pressure
  8. Injector compensation code
  9. Fuel leak
  10. Glow plug
  11. Fuel pressure sensor
  12. EDU (P0200 set simultaneously)
  13. Vehicle modifications
  14. Low quality fuel
  15. Frozen fuel
  16. ECM

HINT:

  1. Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors of the malfunction.
  2. Check that the vehicle has not been modified in any way prior to the vehicle inspection.
  3. This troubleshooting procedure checks for the cause of an obvious lack of engine power (the vehicle speed does not reach the target speed in the high speed range) while the vehicle is being driven.

Inspection procedure

NOTICE:

  1. After replacing the supply pump, the ECM needs initialization.
  2. After replacing the injector, the ECM needs registration.

HINT:

  1. Before troubleshooting, conduct the following:
    1. Check the fuel quality.
    2. Check the fuel for air.
    3. Check the fuel system for blockages.
    4. Check the air filter.
    5. Check the engine oil.
    6. Check the engine coolant.
    7. Check the engine idling speed and the maximum engine speed.
    8. Check the vacuum pump.
1.CHECK WIRE HARNESS AND CONNECTOR IN ENGINE ROOM

  1. Check the wire harness and connector connections of common rail system components.

    HINT:

    Check the following components and system:

    1. Sensors
    2. Supply pump
    3. Common rail
    4. Injectors
    5. EDU
    6. Turbocharger system
    7. Intake and exhaust system

    OK:

    The wire harnesses and connectors are connected securely.

  NG  
REPAIR OR REPLACE HARNESS AND CONNECTOR
 
OK  
   
2.PERFORM CONFIRMATION DRIVING PATTERN

HINT:

Drive the vehicle according to the driving pattern below to allow the ECM to set DTCs relating to malfunctions of the fuel system, EGR system, and throttle valve. If DTCs are set, problem areas can be identified.

  1. Start the engine (procedure "A").

  2. Stop the engine and wait for at least 10 seconds (procedure "B").

  3. Perform procedure "A" and procedure "B" again described above to allow the ECM to set pressure discharge valve malfunction DTCs.

  4. Enter CHECK MODE.

  5. Fully warm up the engine.

  6. Allow the engine to idle for 5 minutes or more.

  7. Drive the vehicle at more than 40 km/h (25 mph) for 1 minute or more (procedure "C").

  8. Decelerate and stop the vehicle (procedure "D").

  9. Repeat procedure "C" and procedure "D" 4 times or more.

  10. Stop the engine and wait for at least 10 seconds (procedure "E").

  11. Repeat procedure "C" and procedure "E" described above to set DTCs relating to the EGR system and throttle valve.

  12. Drive the vehicle at more than 70 km/h (43 mph) for at least 1 minute (to set DTCs relating to the supply pump).

NEXT  
   
3.READ OUTPUT DTC (RELATING TO ENGINE)

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG) and turn the tester ON.

  3. Enter the following menus: Powertrain / Engine and ECT / DTC.

  4. Read pending DTCs.

    Result:
    Display (DTC Output) Proceed to
    No DTCs A
    Engine related DTCs B
  B  
GO TO DTC CHART
 
A  
   
4.PERFORM ACTIVE TEST BY INTELLIGENT TESTER (TEST THE FUEL LEAK)

HINT:

By performing this Active Test, the engine speed is maintained at 2,000 rpm and the common rail internal fuel pressure is raised to the maximum operating pressure. As a result, a fuel leak check can be conducted while retaining the high common rail pressure.

  1. Connect the intelligent tester to the DLC3.

  2. Start the engine and turn the tester ON.

  3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.

  4. Visually check the supply pump, injector and fuel line located between the supply pump and common rail for fuel leaks and fuel pressure leaks. Also, perform the same check on the fuel line between the common rail and the injector.

    HINT:

    There may be fuel leaks inside the components, such as the supply pump.

    OK:

    No leakage.

  NG  
REPAIR OR REPLACE FUEL LEAKAGE POINT
 
OK  
   
5.CHECK WHITE SMOKE

  1. Rev up the engine from idling to 3,000 rpm several times to check whether white smoke is emitted from the exhaust pipe.

  2. Check that the intake system pipes and hoses are not excessively contaminated with oil.
    If white smoke is emitted from the intake system, its pipes and hoses are excessively contaminated with oil. If the presence of white smoke in the exhaust gas is confirmed, there is a high possibility of mechanical problems in the turbocharger or engine.

    Result:
    Result Proceed to
    No problems described above A
    White smoke emitted, or intake system pipes and hoses excessively contaminated with oil B
  B  
Go to step 27
 
A  
   
6.READ VALUE OF MANIFOLD ABSOLUTE PRESSURE SENSOR, MAF METER AND FUEL PRESSURE SENSOR (MAP AND FUEL PRESS)

  1. Connect the intelligent tester to the DLC3.

  2. Start the engine and warm it up and turn the tester ON.

  3. Enter the following menus: Powertrain / Engine and ECT / Data List.

  4. Select the following menu items in order and read the values.

    1. MAP
    2. MAF
    3. Fuel Press
     

    Standard value:

    Item Engine Speed*1 Standard Range Description
    MAP*2 Ignition switch on (IG) (engine stopped) Same as atmospheric pressure Intake manifold internal pressure detected by manifold absolute pressure sensor
    Idling 85 to 93 kPa (690 to 765 mmHg, 27.17 to 30.13 in.Hg)
    3,000 rpm (no engine load) 120 to 140 kPa (803 to 878 mmHg, 31.60 to 34.56 in.Hg)
    3,000 rpm (driving with full throttle acceleration)*5 239 to 259 kPa (1,795 to 1,945 mmHg, 70.67 to 76.57 in.Hg)
    3600 rpm (driving with full throttle acceleration)*5 245 to 265 kPa (1,840 to 1,990 mmHg, 57.00 to 62.91 in.Hg)
    MAF*2, *4 Ignition switch on (IG) (engine stopped) 0 g/sec. Intake air volume detected by mass air flow meter
    Idling 2.5 to 5.52 g/sec.
    3,000 rpm (no engine load) 49 to 57 g/sec.
    3,000 rpm (driving with full throttle acceleration)*5 124 to 136 g/sec.
    3,600 rpm (driving with full throttle acceleration)*5 151 to 163 g/sec.
    Common Rail Pressure*3 Idling 37 to 43 MPa Common rail internal fuel pressure
    2,000 rpm (no engine load) 47 to 53 MPa
    3,000 rpm (no engine load) 60 to 66 MPa
    3,000 rpm (driving with full throttle acceleration)*5 150 to 156 MPa
    3,600 rpm (driving with full throttle acceleration)*5 175 to 185 MPa
     
    Result:
     
    Item Result Proceed to
    MAP, MAF, and Fuel press Standard range A
    MAP and MAF Outside standard range B
    Only MAP Outside standard range C
    Only MAF Outside standard range D
    Only Fuel Press Outside standard range E

    HINT:

    *1: The A/C switch and all accessory switches should be OFF with a fully warm engine.

    *2: This value is indicated when the ambient temperature is 25°C (77°F), the atmospheric pressure is 101 kPa (758 mmHg, 29.83 in.Hg), and the stable boost pressure is maintained for approximately 10 seconds.

    *3: This value is indicated when the ambient temperature is 25°C (77°F), the atmospheric pressure is 101 kPa (758 mmHg, 29.83 in.Hg), and the vehicle is accelerated for approximately 10 seconds.

    *4: When the mass air flow meter malfunctions, the MAF output may deviate from the standard (referential) range when the engine idles and is accelerated from 3,000 to 4,000 rpm with full throttle acceleration.

    *5: Fully depress the accelerator pedal with the vehicle creeping at idle speed in 2nd gear.

  B  
Go to step 24
 
  C  
GO TO DTC P0105, P0107, AND P0108 (RELATED TO MANIFOLD ABSOLUTE PRESSURE SENSOR)
 
  D  
GO TO DTC P0100, P0102, AND P0103 (RELATED TO MAF METER)
 
  E  
Go to step 34
 
A  
   
7.READ VALUE OF INJECTOR (INJECTION FEED BACK VAL AND INJECTION VOLUME)

  1. Connect the intelligent tester to the DLC3.

  2. Start the engine, warm it up, and turn the tester ON.

  3. Select the following menu items in order and read the values.

    1. Injection Feedback Val #1, #2, #3, and #4
    2. Injection Volume
     

    Standard value:

     
    Item Engine Speed* Standard Range Description
    Injection Feedback Val #1 Idling -3.0 to 3.0 mm3 Value of injector fuel injection volume compensates for differences in combustion condition of cylinders
    1. Positive values indicate control which corrects combustion degradation
    2. Negative values indicate control which corrects excessive combustion pressure
    3. If problems exist, "Injection Feedback Val" may deviate from the -3.0 and 3.0 mm3 range
    Injection Feedback Val #2 Idling -3.0 to 3.0 mm3
    Injection Feedback Val #3 Idling -3.0 to 3.0 mm3
    Injection Feedback Val #4 Idling -3.0 to 3.0 mm3
    Injection Volume Idling 3.9 to 7.0 mm3 Fuel injection volume value controlled by ECU
    1. Controls NE signal, fuel temperature, engine coolant temperature, intake air temperature, boost pressure, atmospheric pressure, and EGR volume
    2. If problems exist, "Injection Volume" may be outside the standard range
     
    Result:
     
    Result Proceed to
    Standard range A
    Injection Feedback Val #1 to #4 and/or Injection Volume outside standard range B

    HINT:

    *: The A/C switch and all accessory switches should be OFF, and the engine should be fully warmed up.

  B  
Go to step 14
 
A  
   
8.CHECK INJECTOR COMPENSATION CODE

  1. Read the injector compensation code.

    HINT:

    If the injector compensation code is not correctly registered, it may cause malfunctions.

  2. Check the injector compensation code.

    OK:

    Compensation code of the installed injector is the same as the one registered in the ECM.

  NG  
REGISTER INJECTOR COMPENSATION CODE
 
OK  
   
9.RESET ECM

  1. Disconnect the cable from the negative (-) battery terminal for at least 2 minutes.

  2. Reconnect the cable to the negative (-) battery terminal.

  3. Check whether the malfunction has been successfully repaired by performing a driving test using the freeze frame data recorded at the time the malfunction occurred.

    OK:

    Malfunction has been repaired successfully.

  OK  
CHECK FOR INTERMITTENT PROBLEMS
 
NG  
   
10.BLEED AIR FROM FUEL SYSTEM

  1. To bleed air from the priming pump, pump the priming pump until it becomes hard and cannot be pumped any more.

NEXT  
   
11.CONFIRM WHETHER LACK OF POWER HAS BEEN SUCCESSFULLY REPAIRED

  1. Check whether the lack of power has been successfully repaired by performing a driving test. Use the freeze frame data recorded at the time the malfunction occurred.

    OK:

    Malfunction has been repaired successfully.

  OK  
END
 
NG  
   
12.INSPECT GLOW PLUG ASSEMBLY

2ad-fhv problems Disconnect the glow plug wire.

  1. Disconnect the glow plug wire.

  2. Measure the resistance of the glow plug.

    Standard resistance:

    Tester Connection Condition Specified Condition
    Glow plug terminal - Body ground 20°C (68°F) Approximately 0.95 ?

    HINT:

    If any one of the glow plugs has an open malfunction, the engine power is insufficient only when the engine is cold.

    NOTICE:

    1. Be careful not to damage the glow plug pipes. Damaging them could cause an open circuit, or shorten the life of the glow plugs.
    2. Keep the glow plug free of oil and fuel while cleaning.
    3. Wipe any oil off the terminal and Bakelite washer with a clean, dry cloth during inspection.
    4. Do not apply more than 11 V to the glow plug as it could cause an open circuit.

  3. Reconnect the glow plug wire.

  NG  
REPAIR OR REPLACE GLOW PLUG ASSEMBLY
 
OK  
   
13.CHECK INTAKE SYSTEM

  1. Check for air leakage and blockage between the air cleaner and turbocharger.

  2. Check for air leakage and blockage between the turbocharger and intake manifold.

    OK:

    No leakage or blockage.

NEXT  
   
END 

14.IDENTIFY MALFUNCTIONING CYLINDER INJECTOR

  1. Follow the instructions in the table below according to the check result of the intelligent tester.

    HINT:

    This operation is based on the premise that the common rail pressure is normal.

     

    Standard value:

     
    Item Engine Speed* Reference Value
    Injection Feedback Val #1 to #4 Idling -3.0 to 3.0 mm3
    Injection Volume Idling 3.9 to 7.0mm3

    HINT:

    *: The A/C switch and all accessory switches should be OFF, and the engine should be fully warmed up.

     
    Result:
     
    Injection Volume Injection Volume
    Injection Feedback Val #1 to #4 Less than 3.9 mm3 Between 3.9 to 7.0 mm3 (Normal) More than 7.0 mm3
    3.0 mm3 or more, -3.0 mm3 or less A B B
    Between -3.0 to 3.0 mm3 - Normal C*

     

    Proceed to Proceed to Descriptions
    A Inspect and repair cylinder injector with revised injection volume of less than -3.0 mm3:
    1. Perform power balance inspection and identify malfunctioning cylinder
    2. Replace malfunctioning cylinder injector
    		 Abnormal value cylinder injector injects excessively large quantity of fuel
    B Identify malfunctioning cylinders by conducting power balance inspection:
    1. Perform power balance inspection to identify malfunctioning cylinders
    2. Clean malfunctioning cylinder injector, check, and repair it
    		 Abnormal value cylinder injector injects excessively small quantity of fuel:
    1. Fuel injection volume too low due to injector nozzle being blocked by deposits
    2. Abnormal value cylinder injector compression decreases
    3. Abnormal value cylinder injector injects excessively large quantity of fuel
    C Inspect and repair all cylinder injectors:
    Clean all cylinder injectors, inspect, and repair them    		 All cylinder injectors inject excessively small quantity of fuel:
    Fuel injection volume too low due to all cylinder injector nozzles being blocked by deposits

    HINT:

    *: When the Injection Volume displayed on the tester is large despite the Fuel Pressure and Injection Feedback Val #1 to #4 in the Data List being normal, the injector may be clogged. In this case, there may be deposits inside or outside the tip of the injector.

    1. Despite the injector functioning normally, the indicated Injection Feedback Val #1 to #4 value may be outside the normal operating range due to compensation for other problems (such as low compression).
    2. Injection Feedback Val #1 to #4 is the value used to correct the fuel injection volumes of each cylinder, in order to optimize (compensate for the unevenness between) all the cylinder combustion conditions. If any of the cylinders malfunction, the fuel injection volumes for the normal cylinders are corrected simultaneously. As a result, the Injection Feedback Val #1 to #4 may deviate from the standard range.
  B  
Go to step 16
 
  C  
Go to step 23
 
A  
   
15.PERFORM ACTIVE TEST BY INTELLIGENT TESTER (INJECTOR CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER)

  1. Connect the intelligent tester to the DLC3.

  2. Start the engine and turn the tester ON.

  3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1, #2, #3, and #4 Fuel Cut.

  4. Check the four cylinders in sequence to identify any faulty cylinders by performing the power balance inspection.

    HINT:

    1. If the engine idle does not change when an injector is disabled, the cylinder being tested is malfunctioning.
    2. If the cylinder being tested is normal, there will be a significant change of idle speed when the fuel injection is stopped for that cylinder.
NEXT  
   
REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER 

16.PERFORM ACTIVE TEST BY INTELLIGENT TESTER (INJECTOR CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER)

  1. Connect the intelligent tester to the DLC3.

  2. Start the engine and turn the tester ON.

  3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1, #2, #3, and #4 Fuel Cut.

  4. Check the four cylinders in sequence to identify any faulty cylinders by performing the power balance inspection.

    HINT:

    1. If the engine idle does not change when an injector is disabled, the cylinder being tested is malfunctioning.
    2. If the cylinder being tested is normal, there will be a significant change of idle speed when the fuel injection is stopped for that cylinder.
NEXT  
   
17.CHECK CYLINDER COMPRESSION PRESSURE

  1. Check the cylinder compression pressure.

    Standard pressure:

    2,700 kPa (27.5 kgf/cm2, 392 psi)

    Minimum pressure:

    2,200 kPa (22.4 kgf/cm2, 319 psi)

    Difference between each cylinder:

    500 kPa (5.1 kgf/cm2, 73 psi)

  NG  
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
 
OK  
   
18.CHECK MALFUNCTIONING CYLINDER'S INJECTOR FOR DEPOSITS

HINT:

If an injector is contaminated with deposits, the fuel injection volume deviates from the standard range. This may cause malfunctions.

  1. Check the injector for any deposits.

    Result:
    Injector Condition Proceed to
    Deposits A
    No deposits B
  B  
REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
 
A  
   
19.CLEAN INJECTOR

  1. Wipe away deposits from the tips of the injectors.

    HINT:

    1. Solvent or carbon removal agents help remove the deposits easily.
    2. Exercise extreme care not to damage the injectors while wiping off the deposits.
NEXT  
   


20.READ VALUE OF INJECTOR (INJECTION FEEDBACK VAL AND INJECTION VOLUME)

  1. Reinstall the injector to the cylinder head.

  2. Connect the intelligent tester to the DLC3.

  3. Turn the ignition switch on (IG) and turn the tester ON.

  4. Start the engine and warm it up.

  5. Enter the following menus: Powertrain / Engine and ECT / Data List.

  6. Select the following menu items in order and read the values.

    1. Injection Feedback Val #1, #2, #3, and #4
    2. Injection Volume
     

    Standard value:

     
    Item Engine Speed* Reference Value
    Injection Feedback Val #1 to #4 Idling -3.0 to 3.0 mm3
    Injection Volume Idling 3.9 to 7.0 mm3

    HINT:

    1. The A/C switch and all accessory switches should be OFF with a fully warm engine.
    2. When the values are outside the standard range, deposits inside the injector may be causing the problem.

    OK:

    Values are within the standard range.

  NG  
REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
 
OK  
   
END 


21.CHECK INJECTORS FOR DEPOSITS (EXCEPT FUEL ADDITION INJECTOR)

HINT:

If an injector is contaminated with deposits, the fuel injection volume deviates from the standard range. This may cause malfunctions.

  1. Check the injector for any deposits.

    Result:
    Injector Condition Proceed to
    Deposits A
    No deposits B
  B  
REPLACE INJECTORS
 
A  
   
22.CLEAN INJECTOR

  1. Wipe away deposits from the tips of the injectors.

    HINT:

    1. Solvent or carbon removal agents help remove the deposits easily.
    2. Exercise extreme care not to damage the injectors while wiping off the deposits.
NEXT  
   

23.READ VALUE OF INJECTOR (INJECTION FEEDBACK VAL AND INJECTION VOLUME)

  1. Reinstall the injector to the cylinder head.

  2. Connect the intelligent tester to the DLC3.

  3. Turn the ignition switch on (IG) and turn the tester ON.

  4. Start the engine and warm it up.

  5. Enter the following menus: Powertrain / Engine and ECT / Data List.

  6. Select the following menu items in order and read the values.

    1. Injection Feedback Val #1, #2, #3, and #4
    2. Injection Volume
     

    Standard value:

     
    Item Engine Speed* Reference Value
    Injection Feedback Val #1 to #4 Idling -3.0 to 3.0 mm3
    Injection Volume #1 to #4 Idling 3.9 to 7.0 mm3

    HINT:

    1. *: The A/C switch and all accessory switches should be OFF with a fully warm engine.
    2. When the values are outside the standard range, deposits inside the injector may be causing the problem.

    OK:

    Values are within the standard range.

  NG  
REPLACE INJECTORS
 
OK  
   
END 

24.CHECK EGR VALVE ASSEMBLY

  1. Check the EGR valve assembly.

  NG  
REPLACE EGR VALVE ASSEMBLY
 
OK  
   
25.INSPECT DIESEL THROTTLE BODY ASSEMBLY

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG) and tester ON.

  3. Enter the following menus: Powertrain / Engine and ECT / Diesel Throttle Angle.

  4. Read the value.

    Standard value:

    Ignition switch on (IG):

    0%

    Idling (Warmed up engine):

    95%

    Accelerator pedal fully depressed:

    0%

  NG  
REPLACE DIESEL THROTTLE BODY ASSEMBLY
 
OK  
   
26.CHECK INTAKE SYSTEM

  1. Check for air leakage and blockage between the air cleaner and turbocharger.

  2. Check for air leakage and blockage between the turbocharger and intake manifold.

    OK:

    No leakage or blockage.

  NG  
REPAIR OR REPLACE MALFUNCTIONING PARTS
 
OK  
   

27.CHECK TURBOCHARGER SUB-ASSEMBLY (MECHANICAL PROBLEM)

  1. Disconnect the air cleaner hose.

  2. Use a mirror to visually check the turbocharger for any mechanical problems.

  3. When the engine is cold, check that the impeller of the turbocharger rotates smoothly, and perform a contact check to confirm if it is damaged.

    OK:

    Impeller rotates smoothly and is not damaged.

  4. Reconnect the air cleaner hose.

  NG  
REPLACE TURBOCHARGER SUB-ASSEMBLY
 
OK  
   
28.CHECK VACUUM HOSE (TURBOCHARGER - VRV, VRV - VACUUM PUMP)

  1. Check that the vacuum hoses are installed correctly.

  2. Check the vacuum hoses for any cracks and damage.

  3. Check the vacuum hoses for air leaks and any blockage.

    OK:

    The vacuum hoses are correctly connected.

  NG  
REPAIR OR REPLACE VACUUM HOSE
 
OK  
   
29.CHECK VRV FOR TURBOCHARGER CONTROL

  1. Check the VRV.

  NG  
REPLACE VRV FOR TURBOCHARGER CONTROL
 
OK  
   
30.INSPECT TURBOCHARGER ACTUATOR

  1. Inspect the actuator.

    OK:

    The valve has no contamination and it moves smoothly.

  NG  
REPLACE TURBOCHARGER SUB-ASSEMBLY
 
OK  
   
31.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

  1. Connect the intelligent tester to the DLC3.

  2. Start the engine and warm it up and turn the tester ON.

  3. Enter the following menus: Powertrain / Engine and ECT / Data List.

  4. Select the following menu items in order and read the values.

    1. MAP
    2. MAF
    3. Fuel Press
     

    Standard value:

    Item Engine Speed*1 Standard Range Description
    MAP*2 Ignition switch on (IG) (engine stopped) Same as atmospheric pressure Intake manifold internal pressure detected by manifold absolute pressure sensor
    Idling 85 to 93 kPa (690 to 765 mmHg, 27.17 to 30.13 in.Hg)
    3,000 rpm (no engine load) 120 to 140 kPa (803 to 878 mmHg, 31.60 to 34.56 in.Hg)
    3,000 rpm (driving with full throttle acceleration)*4 239 to 259 kPa (1,795 to 1,945 mmHg, 70.67 to 76.57 in.Hg)
    3600 rpm (driving with full throttle acceleration)*4 245 to 265 kPa (1,840 to 1,990 mmHg, 57.00 to 62.91 in.Hg)
    MAF*2, *3 Ignition switch on (IG) (engine stopped) 0 g/sec. Intake air volume detected by mass air flow meter
    Idling 2.5 to 5.52 g/sec.
    3,000 rpm (no engine load) 49 to 57 g/sec.
    3,000 rpm (driving with full throttle acceleration)*4 124 to 136 g/sec.
    3,600 rpm (driving with full throttle acceleration)*4 151 to 163 g/sec.

    HINT:

    *1: The A/C switch and all accessory switches should be OFF with a fully warm engine.

    *2: This value is indicated when the ambient temperature is 25°C (77°F), the atmospheric pressure is 101 kPa (758 mmHg, 29.83 in.Hg), and the stable boost pressure is maintained for approximately 10 seconds.

    *3: When the mass air flow meter malfunctions, the MAF output may deviate from the standard (referential) range when the engine idles and is accelerated from 3,000 to 4,000 rpm with full throttle acceleration.

    *4: Fully depress the accelerator pedal with the vehicle creeping at idle speed in 2nd gear.

    OK:

    The values are within the standard range.

  OK  
END
 
NG  
   
32.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
NEXT  
   
33.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

  1. Connect the intelligent tester to the DLC3.

  2. Start the engine, warm it up, and turn the tester ON.

  3. Enter the following menus: Powertrain / Engine and ECT / Data List.

  4. Select the following menu items in order and read the values.

    1. MAP
    2. MAF
    3. Fuel Press
     

    Standard value:

     
    Item Engine Speed*1 Standard Range Description
    MAP*2 Ignition switch on (IG) (engine stopped) Same as atmospheric pressure Intake manifold internal pressure detected by manifold absolute pressure sensor
    Idling 85 to 93 kPa (690 to 765 mmHg, 27.17 to 30.13 in.Hg)
    3,000 rpm (no engine load) 120 to 140 kPa (803 to 878 mmHg, 31.60 to 34.56 in.Hg)
    3,000 rpm (driving with full throttle acceleration)*4 239 to 259 kPa (1,795 to 1,945 mmHg, 70.67 to 76.57 in.Hg)
    3600 rpm (driving with full throttle acceleration)*4 245 to 265 kPa (1,840 to 1,990 mmHg, 57.00 to 62.91 in.Hg)
    MAF*2, *3 Ignition switch on (IG) (engine stopped) 0 g/sec. Intake air volume detected by mass air flow meter
    Idling 2.5 to 5.52 g/sec.
    3,000 rpm (no engine load) 49 to 57 g/sec.
    3,000 rpm (driving with full throttle acceleration)*4 124 to 136 g/sec.
    3,600 rpm (driving with full throttle acceleration)*4 151 to 163 g/sec.

    HINT:

    *1: The A/C switch and all accessory switches should be OFF with a fully warm engine.

    *2: This value is indicated when the ambient temperature is 25°C (77°F), the atmospheric pressure is 101 kPa (758 mmHg, 29.83 in.Hg), and the stable boost pressure is maintained for approximately 10 seconds.

    *3: When the mass air flow meter malfunctions, the MAF output may deviate from the standard (referential) range when the engine idles and is accelerated from 3,000 to 4,000 rpm with full throttle acceleration.

    *4: Fully depress the accelerator pedal with the vehicle creeping at idle speed in 2nd gear.

    OK:

    The values are within the standard range.

  NG  
REPLACE TURBOCHARGER SUB-ASSEMBLY
 
OK  
   
END 

34.CHECK AND REPLACE FUEL FILTER ASSEMBLY
NEXT  
   
35.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

  1. Connect the intelligent tester to the DLC3.

  2. Start the engine and warm it up, and turn the tester ON.

  3. Enter the following menus: Powertrain / Engine and ECT / Data List.

  4. Select the following menu item and read the values.

    1. Fuel Press
     

    Standard value:

     
    Item Engine Speed*1 Reference Value
    Fuel Press Idling 37 to 43 MPa
    Fuel Press 2,000 rpm (no engine load) 47 to 53 MPa
    Fuel Press 3,000 rpm (no engine load) 60 to 66 MPa
    Fuel Press 3,600 rpm (driving with full throttle acceleration)*2 175 to 185 MPa

    HINT:

    *1: The A/C switch and all accessory switches should be OFF, and the engine should be fully warmed up.

    *2: Fully depress the accelerator pedal with the vehicle creeping at idle speed in 2nd gear. idle speed in 2nd gear.

    OK:

    The values are within the standard range.

  OK  
END
 
NG  
   
36.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)

2ad-fhv problems Disconnect the B60 fuel pressure sensor connector.

  1. Disconnect the B60 fuel pressure sensor connector.

  2. Measure the resistance of each terminal of the fuel pressure sensor.

    Standard resistance:

    Tester Connection Specified Condition
    B60-5 (PR) - B60-4 (E2) 16.4 k? or less
    B60-2 (PR2) - B60-3 (E2S) 16.4 k? or less
    B60-5 (PR) - B60-6 (VC) 3 k? or less
    B60-2 (PR2) - B60-1 (VC2) 3 k? or less

  3. Reconnect the fuel pressure sensor connector.

  NG  
REPLACE COMMON RAIL ASSEMBLY
 
OK  
   
37.INSPECT SUPPLY PUMP ASSEMBLY

  1. Measure the resistance of the suction control valve terminals.

    Standard resistance:

    Condition Specified Condition
    20°C (68°F) 1.9 to 2.3 ?
  NG  
REPLACE SUPPLY PUMP ASSEMBLY
 
OK  
   
CHECK AND REPLACE COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE) 

Tags