Transmission Control Cable Assembly -- Replacement |
| 1. REMOVE REAR CONSOLE BOX SUB-ASSEMBLY |
Remove the console box (see page RAV4_ACA30 RM000001RHJ000X_01_0019.html).
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- ПРЕДОСТЕРЕЖЕНИЕ:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
| 3. REMOVE BATTERY |
Loosen the nut and remove the bolt and battery clamp.
Remove the battery.
Remove the battery tray.
Remove the 4 bolts and battery carrier.
Remove the 2 bolts and battery bracket reinforcement.
| 4. REMOVE AIR CLEANER ASSEMBLY |
Disconnect the mass air flow meter connector.
Remove the 2 clamps of the engine wire.
 |
Remove the 4 bolts from the air cleaner case.
 |
Disconnect the air cleaner case from the No. 1 air cleaner inlet.
| 5. REMOVE TRANSAXLE CONTROL CABLE ASSEMBLY |
 |
Remove the nut and disconnect the control cable from the control shaft lever.
Remove the clip and disconnect the control cable from the control cable bracket.
 |
Disconnect the control cable from the control cable support.
 |
Remove the bolt and disconnect the clamp of the control cable.
 |
Disconnect the control cable from the shift lever.
 |
Turn the nut and disconnect the control cable from the shift lever retainer.
 |
Remove the 2 bolts and control cable.
 |
| 6. INSTALL TRANSAXLE CONTROL CABLE ASSEMBLY |
Install the control cable with the 2 bolts.
- Момент затяжки:
- 5.0 Н*м{51 кгс*см, 44 фунт-сила-дюймов}
|
Turn the nut of the control cable and push in the lock.
 |
Install the control cable onto the shift lever retainer.
- ПРИМЕЧАНИЕ:
Install the cable with the protruding portion of the cable outer facing upward.
- After installing, check that the lock of the cable outer is protruding beyond portion A-A, as shown in the illustration.
 |
Connect the control cable to the shift lever.
- ПРИМЕЧАНИЕ:
- Connect the control cable so that the adjusting mechanism lock of the control cable is installed on the driver side of the vehicle.
 |
Fix the control cable onto the control cable bracket with the clip.
|
Connect the control cable onto the control shaft lever with the nut.
- Момент затяжки:
- 12 Н*м{122 кгс*см, 9 фунт-сила-футов}
|
Connect the clamp of the control cable with the bolt.
- Момент затяжки:
- 12 Н*м{122 кгс*см, 9 фунт-сила-футов}
|
Connect the control cable to the cable support.
|
| 7. INSTALL AIR CLEANER ASSEMBLY |
Connect the air cleaner case to the No. 1 air cleaner inlet.
Install the air cleaner case with the 4 bolts.
- Момент затяжки:
- 5.0 Н*м{51 кгс*см, 44 фунт-сила-дюймов}
|
Connect the 2 clamps of the engine wire.
|
Connect the mass air flow meter connector.
| 8. INSTALL BATTERY |
Install the battery bracket reinforcement with the 2 bolts.
- Момент затяжки:
- 20 Н*м{204 кгс*см, 15 фунт-сила-футов}
Install the battery carrier with the 4 bolts.
- Момент затяжки:
- 20 Н*м{204 кгс*см, 15 фунт-сила-футов}
Install the battery tray.
Connect the 2 clamps of the engine wire.
Install the battery with the battery clamp.
- Момент затяжки:
- 8.5 Н*м{87 кгс*см, 75 фунт-сила-дюймов} for bolt
- 5.0 Н*м{51 кгс*см, 44 фунт-сила-дюймов} for nut
| 9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 10. INSPECT SHIFT LEVER POSITION |
When shifting the lever from P to the R position with the ignition switch on (IG) and the brake pedal depressed, make sure that the shift lever moves smoothly and moves correctly into position.
Start the engine and make sure that the vehicle moves forward when shifting the lever from N to the D position and moves rearward when shifting the lever to the R position.
If the operation cannot be performed as specified, inspect the park/neutral position switch and check the shift lever installation condition.
| 11. ADJUST SHIFT LEVER POSITION |
Переведите рычаг переключения передач в положение N.
Сдвиньте крышку регулировочного блока в направлении, показанном на рисунке, и вытяните фиксатор.
 |
Осторожно рукой оттяните тягу троса в направлении задней части автомобиля, чтобы туго натянуть трос.
Вдавите фиксатор в регулировочный блок, чтобы зафиксировать его.
 |
Сдвиньте крышку в направлении, показанном на рисунке.
- ПРИМЕЧАНИЕ:
- Задвигайте крышку за выступ на фиксаторе.
 |
По окончании регулировки проверьте работу механизма.
| 12. INSTALL REAR CONSOLE BOX SUB-ASSEMBLY |
Install the rear console box (see page RAV4_ACA30 RM000001RHG000X_01_0010.html).