Dtc P0110 Intake Air Temperature Circuit

Двигатель. Toyota Rav4. Aca30, 33, 38 Ala30
Система Управления Двигателем 2Ad-Ftv. Toyota Rav4. Aca30, 33, 38 Ala30

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

READ VALUE OF MASS AIR FLOW METER

READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

CHECK WIRE HARNESS (MASS AIR FLOW METER - ECM)

READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

CHECK WIRE HARNESS (MASS AIR FLOW METER - ECM)

DTC P0110 Intake Air Temperature Circuit

DTC P0112 Intake Air Temperature Circuit Low Input

DTC P0113 Intake Air Temperature Circuit High Input


DESCRIPTION

The intake air temperature sensor is built into the mass air flow meter and senses the intake air temperature.
Toyota Rav4. Aca30, 33, 38 Ala30.Система Управления Двигателем 2Ad-Ftv.Система Ecd. Dtc P0110 Intake Air Temperature Circuit
A thermistor built in the sensor changes its resistance value according to the intake air temperature.
The lower the intake air temperature, the greater the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (see Fig. 1).
The intake air temperature sensor is connected to the ECM.
The 5 V power source voltage in the ECM is applied to the intake air temperature sensor from terminal THA via resistor R.
The resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes in accordance with changes in the intake air temperature, the potential at terminal THA also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability with a cold engine.

DTC No.
DTC Detection Condition
Trouble Area
P0110
Open or short in IAT sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Open or short in IAT sensor circuit
  2. IAT sensor (built into mass air flow meter)
  3. ECM
P0112
Short in IAT sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Open or short in IAT sensor circuit
  2. IAT sensor (built into mass air flow meter)
  3. ECM
P0113
Open in IAT sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Open or short in IAT sensor circuit
  2. IAT sensor (built into mass air flow meter)
  3. ECM

УКАЗАНИЕ:
When DTC P0110, P0112, or P0113 is detected, check the intake air temperature by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Intake Air.

Reference:
Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
140°C (284°F) or more
Short circuit

WIRING DIAGRAM


Toyota Rav4. Aca30, 33, 38 Ala30.Система Управления Двигателем 2Ad-Ftv.Система Ecd. Dtc P0110 Intake Air Temperature Circuit


INSPECTION PROCEDURE

ПРИМЕЧАНИЕ:
After replacing the ECM, the new ECM needs registration (see page RAV4_ACA30 RM000000TJ400AX.html) and initialization (see page RAV4_ACA30 RM000000TIN009X.html).
УКАЗАНИЕ:
If DTCs relating to different systems are output, and they share terminal E2 as their ground, check this ground circuit first.
1.READ VALUE OF MASS AIR FLOW METER

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value.

    Standard value:
    Same value as the actual air temperature.
    Result:
    Temperature Displayed
    		Proceed to
    -40°C (-40°F)
    		A
    140°C (284°F) or more
    		B
    OK (same as air temperature near intake manifold)
    		C
    УКАЗАНИЕ:
    1. If there is an open circuit, the tester indicates -40°C (-40°F).
    2. If there is a short circuit, the tester indicates 140°C (284°F) or more.


B
Перейдите к шагу 4

C
CHECK FOR INTERMITTENT PROBLEMS
A


2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)


    Toyota Rav4. Aca30, 33, 38 Ala30.Система Управления Двигателем 2Ad-Ftv.Система Ecd. Dtc P0110 Intake Air Temperature Circuit

  1. Disconnect the B34 mass air flow meter connector.

  1. Connect terminals THA and E2 of the mass air flow meter wire harness side connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value.

    Standard value:
    140°C (284°F) or more

  1. Reconnect the mass air flow meter connector.



OK
CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER
NG


3.CHECK WIRE HARNESS (MASS AIR FLOW METER - ECM)


    Toyota Rav4. Aca30, 33, 38 Ala30.Система Управления Двигателем 2Ad-Ftv.Система Ecd. Dtc P0110 Intake Air Temperature Circuit

  1. Disconnect the B34 mass air flow meter connector.

  1. Disconnect the B32 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    		Specified Condition
    B34-4 (THA) - B32-110 (THA)
    		Below 1 Ω
    B34-5 (E2) - B32-87 (ETHA)
    		Below 1 Ω

  1. Reconnect the mass air flow meter connector.

  1. Reconnect the ECM connector.



OK
REPAIR OR REPLACE HARNESS AND CONNECTOR
NG

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)


    Toyota Rav4. Aca30, 33, 38 Ala30.Система Управления Двигателем 2Ad-Ftv.Система Ecd. Dtc P0110 Intake Air Temperature Circuit

  1. Disconnect the B34 mass air flow meter connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value.

    Standard value:
    -40°C (-40°F)

  1. Reconnect the mass air flow meter connector.



OK
REPLACE MASS AIR FLOW METER
NG


5.CHECK WIRE HARNESS (MASS AIR FLOW METER - ECM)


    Toyota Rav4. Aca30, 33, 38 Ala30.Система Управления Двигателем 2Ad-Ftv.Система Ecd. Dtc P0110 Intake Air Temperature Circuit

  1. Disconnect the B34 mass air flow meter connector.

  1. Disconnect the B32 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    		Specified Condition
    B34-4 (THA) or B32-110 (THA) - Body ground
    		10 kΩ or higher

  1. Reconnect the mass air flow meter connector.

  1. Reconnect the ECM connector.



OK
REPAIR OR REPLACE HARNESS AND CONNECTOR
NG

REPLACE ECM