Knock Sensor -- Removal |
| 1. DISCHARGE FUEL SYSTEM PRESSURE |
- ПРЕДОСТЕРЕЖЕНИЕ:
- DISCHARGE FUEL SYSTEM PRESSURE procedures must be performed before disconnecting any part of the fuel system.
- After performing the DISCHARGE FUEL SYSTEM PRESSURE procedures, pressure will remain in the fuel line. When disconnecting the fuel line, place a cloth or equivalent over fittings to reduce the risk of fuel spray.
Remove the console box (see page RAV4_ACA30 RM000001RHJ000X_01_0010.html).
Disconnect the connector.
 |
Start the engine. After the engine has stopped, turn the ignition switch off.
- УКАЗАНИЕ:
- DTC P0171 (system too lean) may be set.
Check that the engine does not start.
Remove the fuel tank cap, and let the air out of the fuel tank.
Connect the connector.
|
Install the console box (see page RAV4_ACA30 RM000001RHG000X_01_0010.html).
| 2. DRAIN COOLANT |
Loosen the radiator drain cock plug.
- УКАЗАНИЕ:
- Collect the coolant in a container and dispose of it according to the regulations in your area.
Remove the radiator reservoir cap.
- ПРЕДОСТЕРЕЖЕНИЕ:
- Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
Loosen the cylinder block drain cock plug.
| 3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- ПРЕДОСТЕРЕЖЕНИЕ:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
| 4. REMOVE NO. 1 ENGINE COVER |
Remove the 2 nuts and engine cover.
 |
| 5. REMOVE AIR CLEANER CAP |
Disconnect the mass air flow meter connector.
 |
Disconnect the purge VSV connector.
Disconnect the 4 wire harness clamps.
Disconnect the No. 2 ventilation hose from the air cleaner hose.
 |
Disconnect the purge line hose from the clamp.
Lock the No. 1 air cleaner hose clamp, and then disconnect the No. 1 air cleaner hose from the throttle body.
 |
Unfasten the 2 hook clamps, and then remove the air cleaner cap.
 |
Remove the air cleaner filter element from the air cleaner case.
| 6. REMOVE THROTTLE BODY |
Disconnect the purge line hose from the throttle body.
 |
Disconnect the water by-pass hose from the throttle body.
Disconnect the No. 2 water by-pass hose from the throttle body.
Disconnect the No. 1 throttle body hose from the throttle body.
Disconnect the throttle position sensor and control motor connector.
Disconnect the wire harness clamp.
Disconnect the fuel tube from the clamp.
Remove the 4 bolts, and then remove the fuel pipe support and throttle body.
 |
Remove the gasket from the intake manifold.
 |
| 7. REMOVE FUEL DELIVERY PIPE |
Remove the 2 wire harness clamps.
 |
Disconnect the 4 fuel injector connectors.
Remove the 2 bolts and then pull out the fuel delivery pipe together with the 4 fuel injectors.
- ПРИМЕЧАНИЕ:
- Be careful not to drop the fuel injectors when removing the fuel delivery pipe.
 |
Remove the 2 delivery pipe spacers from the cylinder head.
 |
Remove the 4 insulators from the cylinder head.
| 8. DISCONNECT FUEL TUBE |
| 9. REMOVE HEATER WATER INLET HOSE |
Remove the hose clamp.
Remove the heater water inlet hose from the heater radiator unit and cylinder head.
| 10. REMOVE HEATER WATER OUTLET HOSE |
Remove the heater water outlet hose from the heater radiator unit and water by-pass pipe.
| 11. REMOVE INTAKE MANIFOLD |
Disconnect the union to check valve hose from the brake booster.
Disconnect the camshaft timing oil control valve connector.
 |
Remove the wire harness clamp.
Remove the union to check valve hose from the vacuum hose clamp.
Remove the 5 bolts, 2 nuts and intake manifold.
Remove the gasket from the intake manifold.
 |
| 12. REMOVE INTAKE MANIFOLD INSULATOR |
Remove the intake manifold insulator from the cylinder block.
 |
| 13. REMOVE KNOCK SENSOR |
Disconnect the sensor connector.
 |
Remove the nut and sensor.