Dtc P2121 Throttle / Pedal Position Sensor / Switch D Circuit Range / Performance

Двигатель. Toyota Rav4. Aca30, 33, 38 Ala30
Система Управления Двигателем 2Az-Fe. Toyota Rav4. Aca30, 33, 38 Ala30

DESCRIPTION

FAIL-SAFE

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2121)

READ VALUE OF INTELLIGENT TESTER (ACCELERATOR POSITION NO.1 AND ACCELERATOR POSITION NO.2)

REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)

DTC P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance


DESCRIPTION


УКАЗАНИЕ:
Refer to DTC P2120 (see page RAV4_ACA30 RM000000PFY01DX.html).

DTC No.
DTC Detection Condition
Trouble Area
P2121
Difference between VPA and VPA2 less than 0.4 V, or more than 1.2 V for 0.5 seconds (1 trip detection logic)
  1. Accelerator Pedal Position (APP) sensor
  1. ECM

FAIL-SAFE

The APP sensor has two (main and sub) sensor circuits. If a malfunction occurs in either of the sensor circuits, the ECM detects the abnormal signal voltage difference between the two sensor circuits and switches to limp mode. In limp mode, the functioning circuit is used to calculate the accelerator pedal opening angle to allow the vehicle to continue driving. If both circuits malfunction, the ECM regards the opening angle of the accelerator pedal as being fully closed. In this case, the throttle valve remains closed as if the engine is idling. If a pass condition is detected and then the ignition switch is turned off, the fail-safe operation stops and the system returns to a normal condition.

WIRING DIAGRAM

Refer to DTC P2120 (see page RAV4_ACA30 RM000000PFY01DX_08.html).

INSPECTION PROCEDURE

УКАЗАНИЕ:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2121)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    		Proceed to
    P2121
    		A
    P2121 and other DTCs
    		B
    УКАЗАНИЕ:
    If any DTCs other than P2121 are output, troubleshoot those DTCs first.


B
GO TO DTC CHART
A


2.READ VALUE OF INTELLIGENT TESTER (ACCELERATOR POSITION NO.1 AND ACCELERATOR POSITION NO.2)
Toyota Rav4. Aca30, 33, 38 Ala30.Система Управления Двигателем 2Az-Fe.Система Sfi. Dtc P2121 Throttle / Pedal Position Sensor / Switch D Circuit Range / Performance

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Accelerator Position No.1 and Accelerator Position No.2.

  1. Read the values displayed on the tester.

    Standard voltage:
    Accelerator Pedal Operation
    		Accelerator Position No.1
    		Accelerator Position No.2
    Released
    		0.5 to 1.1 V
    		1.2 to 2.0 V
    Depressed
    		2.6 to 4.5 V
    		3.4 to 5.0 V


OK
CHECK FOR INTERMITTENT PROBLEMS
NG


3.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

NEXT


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Clear DTCs (see page RAV4_ACA30 RM000000PDK013X.html).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    		Proceed to
    P2121
    		A
    No output
    		B


B
SYSTEM OK
A

REPLACE ECM