Приводной Ремень Газораспределения Снятие

Двигатель Гибридная Система Land Cruiser Prado.
Механическая Часть Двигателя 5L-E.

  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  2. REMOVE FAN SHROUD

  3. REMOVE VANE PUMP DRIVE PULLEY

  4. REMOVE CRANKSHAFT PULLEY

  5. REMOVE IDLE PULLEY ASSEMBLY

  6. REMOVE TIMING BELT COVER

  7. REMOVE TIMING BELT GUIDE

  8. SET NO. 1 CYLINDER TO TDC/COMPRESSION

  9. REMOVE TIMING BELT

  10. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

Приводной Ремень Газораспределения -- Снятие



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
ПРИМЕЧАНИЕ:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page Нажмите здесь).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page Нажмите здесь).


2. REMOVE FAN SHROUD

  1. Remove the fan shroud (See page Нажмите здесь).



3. REMOVE VANE PUMP DRIVE PULLEY



  1. Remove the 4 bolts, vane pump drive pulley and cooler compressor drive pulley.



4. REMOVE CRANKSHAFT PULLEY


.Механическая Часть Двигателя 5L-E.Двигатель.Приводной Ремень Газораспределения Снятие

  1. Using SST, remove the pulley bolt.

    SST
    09213-54015(91651-60855)
    09330-00021
    Text in Illustration
    *a
    		Hold
    *b
    		Turn


    .Механическая Часть Двигателя 5L-E.Двигатель.Приводной Ремень Газораспределения Снятие

  1. Using SST, remove the pulley.

    SST
    09950-50013(09951-05010,09952-05010,09953-05020,09954-05021)
    09950-60010(09951-00490)
    09950-40011(09957-04010)
    Text in Illustration
    *a
    		Hold
    *b
    		Turn


5. REMOVE IDLE PULLEY ASSEMBLY



  1. Remove the 2 bolts and Idle pulley bracket.



6. REMOVE TIMING BELT COVER



  1. Remove the 11 bolts, washers, timing belt cover, and 2 gaskets.



7. REMOVE TIMING BELT GUIDE

  1. Remove the timing belt guide.



8. SET NO. 1 CYLINDER TO TDC/COMPRESSION


    .Механическая Часть Двигателя 5L-E.Двигатель.Приводной Ремень Газораспределения Снятие

  1. Using the crankshaft pulley bolt, align the groove of the crankshaft pulley with the timing pointer by turning the crankshaft clockwise.

    Text in Illustration
    *1
    		Timing Mark

    		Turn


    .Механическая Часть Двигателя 5L-E.Двигатель.Приводной Ремень Газораспределения Снятие

  1. Check that the timing marks of the camshaft timing pulley and No. 2 timing belt cover are aligned.

    Text in Illustration
    *1
    		Timing Mark
    If not, turn the crankshaft 1 revolution (360°).


9. REMOVE TIMING BELT
УКАЗАНИЕ:
If reusing the timing belt, draw a direction arrow on the timing belt (in the direction the belt move when the engine is running), and place matchmarks on the pulleys and timing belt.



  1. Turn the crankshaft 90° counterclockwise, and align the timing mark of the crankshaft timing pulley with the protrusion of the timing belt case.

    Text in Illustration

    		Turn
    ПРИМЕЧАНИЕ:
    If the timing belt is disengaged, having the crankshaft timing pulley at the wrong angle can cause the piston head and valve head to come into contact with each other when removing the camshaft timing pulley, and camshaft causing damage. Therefore, always set the crankshaft pulley is removed at the correct angle.


    .Механическая Часть Двигателя 5L-E.Двигатель.Приводной Ремень Газораспределения Снятие

  1. Loosen the No. 1 timing belt idler bolt (A), and shift the idler to the left as far as possible.

    Text in Illustration

    		Pry

    		Move

  1. Tighten the No. 1 timing belt idler bolt (A), and then relieve the timing belt tension.

  1. Remove the timing belt.



10. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

  1. Remove the 2 bolts (A and B).



    .Механическая Часть Двигателя 5L-E.Двигатель.Приводной Ремень Газораспределения Снятие

  1. Loosen the bolt (C), and remove the No. 1 timing belt idler.