Распредвал -- Снятие |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- ПРИМЕЧАНИЕ:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page Нажмите здесь).
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page Нажмите здесь).
| 2. REMOVE UPPER RADIATOR SUPPORT SEAL |
Освободите 13 фиксаторов и снимите верхнее уплотнение кронштейна радиатора.
| 3. REMOVE FRONT BUMPER COVER LOWER |
Remove the clip, 5 bolts and front bumper cover lower.
| 4. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY |
Remove the 4 bolts.
Unhook the engine under cover from the vehicle body as shown in the illustration.
 |
| 5. DRAIN ENGINE COOLANT |
- ПРЕДОСТЕРЕЖЕНИЕ:
- Не снимайте пробку расширительного бачка радиатора, пока двигатель и радиатор не остынут. Выброс горячей охлаждающей жидкости и пара под давлением может стать причиной серьезных ожогов.
Ослабьте пробку сливного крана радиатора.
Обозначения на рисунке *1 Пробка радиатора *2 Бачок радиатора *3 Пробка сливного крана радиатора *4 Пробка сливного крана блока цилиндров - УКАЗАНИЕ:
- Слейте охлаждающую жидкость в контейнер и утилизируйте ее в соответствии с местными требованиями.
Слейте охлаждающую жидкость, сняв крышку радиатора.
Ослабьте пробку сливного крана блока цилиндров.
Ослабьте пробку сливного крана блока цилиндров и слейте охлаждающую жидкость из двигателя.
- ПРИМЕЧАНИЕ:
- Если охлаждающая жидкость не сливается через пробку сливного крана радиатора, пробки сливных кранов блока цилиндров и расширительный бачок радиатора, возможны засорение радиатора и утечка охлаждающей жидкости через уплотнение насоса системы охлаждения.
| 6. REMOVE FRONT FENDER APRON SEAL RH |
Remove the 4 clips and fender apron seal.
| 7. REMOVE RESONATOR WITH AIR CLEANER CAP SUB-ASSEMBLY |
Disconnect the sensor connector.
 |
Detach the wire harness clamp.
Loosen the hose clamp and remove the resonator with air cleaner cap.
Detach the 4 hook clamps, and then remove the air cleaner cap and resonator with air cleaner cap.
 |
| 8. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
| 9. REMOVE AIR CLEANER CASE ASSEMBLY |
Remove the 3 bolts and air cleaner case.
 |
| 10. DISCONNECT WIRE HARNESS |
Remove the terminal cap.
Remove the nut and generator wire.
 |
Disconnect the generator connector and cooler compressor connector.
Detach the 4 wire harness clamps.
for LHD:
Detach the 4 wire harness clamps.
 |
| 11. REMOVE WIRING HARNESS CLAMP BRACKET (for LHD) |
Remove the bolt and wiring harness clamp bracket.
 |
| 12. REMOVE NO. 1 RADIATOR HOSE |
Detach the clamp and remove the No. 1 radiator hose.
 |
Remove the 2 nuts and hose clamp.
 |
| 13. REMOVE RADIATOR RESERVE TANK ASSEMBLY |
Disconnect the reservoir hose from the upper side of the radiator tank.
 |
Remove the 3 bolts and radiator reservoir.
| 14. REMOVE FAN SHROUD |
Loosen the 4 nuts holding the fluid coupling fan.
 |
Remove the vane pump V belt and the fan and generator V belt (See page Нажмите здесь).
Remove the 2 bolts holding the fan shroud.
 |
Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.
- ПРИМЕЧАНИЕ:
- Be careful not to damage the radiator core.
Remove the fan pulley from the water pump.
| 15. REMOVE VANE PUMP DRIVE PULLEY |
 |
Remove the 4 bolts, vane pump drive pulley and cooler compressor drive pulley.
| 16. REMOVE CRANKSHAFT PULLEY |
 |
Using SST, remove the pulley bolt.
- SST
- 09213-54015(91651-60855)
09330-00021
Text in Illustration *a Hold *b Turn
Using SST, remove the pulley.
- SST
- 09950-50013(09951-05010,09952-05010,09953-05020,09954-05021)
09950-60010(09951-00490)
09950-40011(09957-04010)
Text in Illustration *a Hold *b Turn
 |
| 17. REMOVE IDLE PULLEY ASSEMBLY |
Remove the 2 bolts and Idle pulley bracket.
 |
| 18. REMOVE TIMING BELT COVER |
Remove the 11 bolts, washers, timing belt cover, and 2 gaskets.
 |
| 19. REMOVE TIMING BELT GUIDE |
Remove the timing belt guide.
| 20. SET NO. 1 CYLINDER TO TDC/COMPRESSION |
Using the crankshaft pulley bolt, align the groove of the crankshaft pulley with the timing pointer by turning the crankshaft clockwise.
Text in Illustration *1 Timing Mark 
Turn
 |
Check that the timing marks of the camshaft timing pulley and No. 2 timing belt cover are aligned.
If not, turn the crankshaft 1 revolution (360°).Text in Illustration *1 Timing Mark
 |
| 21. REMOVE TIMING BELT |
- УКАЗАНИЕ:
- If reusing the timing belt, draw a direction arrow on the timing belt (in the direction the belt move when the engine is running), and place matchmarks on the pulleys and timing belt.
Turn the crankshaft 90° counterclockwise, and align the timing mark of the crankshaft timing pulley with the protrusion of the timing belt case.
Text in Illustration Turn - ПРИМЕЧАНИЕ:
- If the timing belt is disengaged, having the crankshaft timing pulley at the wrong angle can cause the piston head and valve head to come into contact with each other when removing the camshaft timing pulley, and camshaft causing damage. Therefore, always set the crankshaft pulley is removed at the correct angle.
 |
Loosen the No. 1 timing belt idler bolt (A), and shift the idler to the left as far as possible.
Text in Illustration Pry 
Move
 |
Tighten the No. 1 timing belt idler bolt (A), and then relieve the timing belt tension.
Remove the timing belt.
| 22. REMOVE INTAKE PIPE |
Loosen the hose clamp and remove the 2 bolts and intake pipe.
 |
| 23. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
Remove the 9 bolts, nut, cylinder head cover and gasket.
| 24. REMOVE CAMSHAFT TIMING PULLEY |
Using the crankshaft pulley bolt, turn the crankshaft 90° counterclockwise and align the timing mark of the crankshaft timing pulley with the protrusion of the timing belt case.
Text in Illustration Turn *1 Timing Mark *2 Protrusion - УКАЗАНИЕ:
- Set the No. 1 cylinder to 90° BTDC/compression to avoid interference with the piston top and valve head.
 |
Using SST, loosen the pulley bolt.
- SST
- 09960-10010(09962-01000,09963-01000)
 |
Using SST, separate the timing pulley from the camshaft.
- SST
- 09950-50013(09951-05010,09952-05010,09953-05010,09954-05021)
 |
Remove the pulley bolt and timing pulley.
Remove the timing pulley woodruff key.
| 25. REMOVE NO. 2 TIMING BELT COVER |
Remove the 4 bolts and timing belt cover.
| 26. REMOVE CAMSHAFT OIL SEAL RETAINER |
Remove the 4 bolts, retainer and gasket.
| 27. REMOVE CAMSHAFT OIL SEAL |
Using a screwdriver and hammer, tap out the oil seal.
 |
| 28. REMOVE CAMSHAFT |
Turn the camshaft with a wrench so that the key groove faces upward.
Text in Illustration *1 Upward *2 Key Groove
 |
Uniformly loosen and remove the 10 bearing cap bolts in several steps in the sequence shown in the illustration.
 |
Remove the 5 bearing caps and camshaft.
- УКАЗАНИЕ:
- Arrange the bearing caps in the correct order.