Трос Механизма Переключения Передач В Сборе (Для Моделей С Кузовом Типа Седан) Установка. Corolla ZZE150

Put the transmission control cable into the cabin and connect the transmission control cable with the 2 nuts.

Момент затяжки:

5.0 Н*м{51 кгс*см, 44 фунт-сила-дюймов}

Install the transmission control cable bracket to the rear engine mounting insulator with the bolt.

Момент затяжки:

5.0 Н*м{51 кгс*см, 44 фунт-сила-дюймов}

Connect the transmission control cable to the transmission control cable bracket with a new clip.

Connect the transmission control cable to the control shaft lever with the nut.

Момент затяжки:

12 Н*м{122 кгс*см, 9 фунт-сила-футов}

Turn the nut of the transmission control cable 180° counterclockwise. While holding the nut in place, push in the stopper until the stopper clicks twice.

Install the outer part of the transmission control cable to the shift lever retainer. Check that the spring is positioned at "A" and push in the stopper.

УКАЗАНИЕ:

If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.

Install the cable end to the shift lever assembly.

ПРИМЕЧАНИЕ:

1. Check that the lock piece is pulled up.
   

1. Install the cable end all the way to the base of the pin.
   

Push the lock piece into the adjuster case.

ПРИМЕЧАНИЕ:

Securely push in the lock piece until it locks.

Install the No. 1 front floor heat insulator with the 3 nuts.

Момент затяжки:

5.5 Н*м{56 кгс*см, 49 фунт-сила-дюймов}

Using vernier calipers, measure the free length of the compression springs.

УКАЗАНИЕ:

If the free length is less than the minimum, replace the compression spring.

Using a plastic hammer and wooden block, tap in a new gasket until its surface is flush with the exhaust manifold.

ПРИМЕЧАНИЕ:

1. Be careful with the installation direction of the gasket.
   
2. Do not reuse the gasket.
   
3. Do not damage the gasket.
   
4. Do not push in the gasket by using the exhaust pipe when connecting it.
   

Install the exhaust pipe support, and then install the front exhaust pipe assembly with the 2 compression springs and 2 bolts.

Момент затяжки:

43 Н*м{439 кгс*см, 32 фунт-сила-футов}

Using a plastic hammer and wooden block, tap in a new gasket until its surface is flush with the front exhaust pipe assembly.

ПРИМЕЧАНИЕ:

1. Be careful with the installation direction of the gasket.
   
2. Do not reuse the gasket.
   
3. Do not damage the gasket.
   
4. Do not push in the gasket by using the exhaust pipe when connecting it.
   

Connect the front exhaust pipe assembly to the center exhaust pipe assembly with the 2 compression springs and 2 bolts.

Момент затяжки:

43 Н*м{439 кгс*см, 32 фунт-сила-футов}

Using SST, install the oxygen sensor to the front exhaust pipe assembly.

SST

09224-00010

Момент затяжки:

without SST:

44 Н*м{449 кгс*см, 32 фунт-сила-футов}

with SST:

40 Н*м{408 кгс*см, 30 фунт-сила-футов}

ПРИМЕЧАНИЕ:

1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.)
   
2. Do not damage the oxygen sensor.
   

Connect the oxygen sensor connector.

Install the air cleaner case with the 3 bolts.

Момент затяжки:

7.0 Н*м{71 кгс*см, 62 фунт-сила-дюймов}

Install the wire harness clamp to the air cleaner case.

Install the air cleaner filter element.

Connect the air cleaner cap sub-assembly with the band.

Connect the ventilation hose.

Connect the 2 clamps.

Connect the mass air flow meter connector.

Engage the 4 clips to install the V-bank cover.

ПРИМЕЧАНИЕ:

1. Be sure to engage the clips securely.
   
2. Do not apply excessive force or do not hit the cover to engage the clips. This may cause the cover to break.
   

Вверните 2 винта.

Установите вещевой ящик в облицовке туннеля пола в сборе и закрепите его 4 болтами и 2 винтами.

Установите коврик вещевого ящика в облицовке туннеля пола.

Установите верхнюю панель консоли и закрепите ее 8 фиксаторами.

Введите в зацепление направляющую.

Введите в зацепление 3 захвата и установите переднюю вставку вещевого ящика в облицовке туннеля пола № 1.

Введите в зацепление направляющую.

Введите в зацепление 3 захвата и установите переднюю вставку вещевого ящика в облицовке туннеля пола № 2.

Введите в зацепление 2 захвата.

Установите ящик панели приборов и закрепите ее 2 винтами <B>.

Введите в зацепление 2 захвата и 2 фиксатора и установите центральную облицовку панели управления в сборе.

Install the shift lever knob sub-assembly.

Введите в зацепление 3 захвата и фиксатор и установите левую нижнюю отделочную накладку панели приборов.

Введите в зацепление 3 захвата и фиксатор и установите правую нижнюю отделочную накладку панели приборов

When moving the lever from the P position to the R position with the ignition switch on (IG) and the brake pedal depressed, make sure that the shift lever moves smoothly and moves correctly into position.

Start the engine and make sure that the vehicle moves forward when moving the lever from the N position to the D position and moves rearward when moving the lever to the R position. If the operation cannot be performed as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.

Apply the parking brake and move the shift lever to the N position.

Remove the rear console box assembly (See page Нажмите здесь).

Disconnect the end of the transmission control cable assembly from the shift lever assembly.

Using a screwdriver, pull out the stopper of the transmission control cable.

ПРИМЕЧАНИЕ:

Do not remove the stopper. If the stopper is removed, reinstall it to its original position.

Rotate the nut counterclockwise approximately 180° and, while holding the nut in that position, disconnect the transmission control cable from the shift lever retainer.

ПРИМЕЧАНИЕ:

Do not over-rotate the nut as it will come off the interior spring and the transmission control cable will not be reusable.

Push the two claws together at the top of the transmission control cable lock piece. While holding the two claws together, push the two lugs on the bottom of the lock piece toward each other and upward to pull out the lock piece.

Turn the nut of the transmission control cable 180° counterclockwise. While holding the nut in place, push in the stopper until the stopper clicks twice.

Install the outer part of the transmission control cable to the shift lever retainer. Check that the spring is positioned at "A" and push in the stopper.

УКАЗАНИЕ:

If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.

Install the cable end to the shift lever assembly.

ПРИМЕЧАНИЕ:

1. Check that the lock piece is pulled up.
   
2. Install the cable end all the way to the base of the pin.
   

Push the lock piece into the adjuster case.

ПРИМЕЧАНИЕ:

Securely push in the lock piece until it locks.

After adjusting the shift lever position, check the operation and function of the shift lever. If there is a problem, adjust the position again.

Install the rear console box assembly (See page Нажмите здесь).