Рычаг Переключения Передач В Сборе (Для Моделей С Кузовом Типа Седан) Установка. Corolla ZZE150
INSTALL SHIFT LEVER ASSEMBLY
INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY
ADJUST TRANSMISSION CONTROL SELECT CABLE
INSTALL REAR CONSOLE BOX ASSEMBLY
INSTALL CONSOLE BOX CARPET
INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY
INSTALL FRONT NO. 1 CONSOLE BOX INSERT
INSTALL FRONT NO. 2 CONSOLE BOX INSERT
INSTALL INSTRUMENT PANEL BOX ASSEMBLY
INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH
INSTALL LOWER INSTRUMENT PANEL FINISH PANEL RH
Рычаг Переключения Передач В Сборе (Для Моделей С Кузовом Типа "Седан") -- Установка |
1. INSTALL SHIFT LEVER ASSEMBLY |
Install the floor shift shift lever with the 4 bolts.
- Момент затяжки:
- 12 Н*м{122 кгс*см, 9 фунт-сила-футов}
2. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY |
Rotate the transmission control cable nut counterclockwise approximately 180° and, while holding the nut in that position, press in the stopper until it makes 2 "click" sounds.
Install the cable outer of the transmission control cable to the shift lever retainer, check that the position of the spring is the same as A shown in the illustration, and press in the stopper.
- ПРИМЕЧАНИЕ:
- If the stopper cannot be pressed in, slightly turn the nut clockwise and then press in the stopper.
Install the control shift cable to the shift lever assembly.
Install the control select cable to the shift lever assembly.
- ПРИМЕЧАНИЕ:
- Make sure that the transmission control cable assembly is securely installed.
Install the clip to the shift lever.
Install the wire harness to the shift lever assembly with the 3 clamps.
3. ADJUST TRANSMISSION CONTROL SELECT CABLE |
- УКАЗАНИЕ:
- After the shift lever or the shift cable is replaced, be sure to adjust the transmission control cable assembly.
- If the shift lever does not move (or the shift lever is difficult to move) to the 1st or 2nd position, or if it is possible to move the shift lever to the reverse position without pulling up the slider shaft, the length of the cable must be adjusted.
Install the transmission control cable assembly on the transmission.
Using a screwdriver, pull the lock piece out from the adjuster case.
Pressing the shift and select lever shaft (*1) and pin (*2), push in pin (*3) and check that the shift and select lever shaft is secured at the 1st-2nd gear selected position (the shaft comes to a stop at the position 8 mm (0.31 in.) below the N position).
Remove the stopper pin, release the lock, and reinsert the stopper pin.
Turn the shift lever in the reverse direction without pulling up the slider shaft.
- ПРИМЕЧАНИЕ:
- When adjusting the cable, make sure that the shift lever is not in the first or second gear position.
Install the transmission control shift cable to the shift lever assembly.
Install the control select cable to the shift lever assembly.
- ПРИМЕЧАНИЕ:
- Make sure that the lock piece is protruded from the adjuster case.
- When adjusting the cable, make sure that the shift lever is not in the first or second gear position.
Install the clip to the shift lever.
Press in and lock the lock piece to the adjuster case.
- ПРИМЕЧАНИЕ:
- Securely press in the lock piece until the lock engages.
Release the pin that fixes the transmission outer lever.
Pull the pin toward the front left side of the vehicle.
4. INSTALL REAR CONSOLE BOX ASSEMBLY |
Вверните 2 винта.
Установите вещевой ящик в облицовке туннеля пола и закрепите его 4 болтами.
5. INSTALL CONSOLE BOX CARPET |
Установите коврик вещевого ящика в облицовке туннеля пола.
6. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY |
Установите верхнюю панель консоли и закрепите ее 8 фиксаторами.
7. INSTALL FRONT NO. 1 CONSOLE BOX INSERT |
Введите в зацепление направляющую.
Введите в зацепление 3 захвата и установите переднюю вставку вещевого ящика в облицовке туннеля пола № 1.
8. INSTALL FRONT NO. 2 CONSOLE BOX INSERT |
Введите в зацепление направляющую.
Введите в зацепление 3 захвата и установите переднюю вставку вещевого ящика в облицовке туннеля пола № 2.
9. INSTALL INSTRUMENT PANEL BOX ASSEMBLY |
Введите в зацепление 2 захвата.
Установите ящик панели приборов и закрепите ее 2 винтами <B>.
10. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY |
Введите в зацепление 2 захвата и 2 фиксатора и установите центральную облицовку панели управления.
11. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY |
Поверните рукоятку рычага переключения передач по часовой стрелке и закрепите ее.
12. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH |
Введите в зацепление 3 захвата и фиксатор и установите левую нижнюю отделочную накладку панели приборов.
13. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL RH |
Введите в зацепление 2 захвата и 2 фиксатора и установите правую отделочную накладку панели приборов.