Система Механической Трансмиссии 'Multimode' Таблица Работы В Аварийном Режиме. Corolla ZZE150

Трансмиссия. COROLLA, AURIS. ZZE150 ZRE151,152 NDE150
Механическая Трансмиссия 'Multimode' C53A. COROLLA, AURIS. ZZE150 ZRE151,152 NDE150

  1. ТАБЛИЦА РАБОТЫ В АВАРИЙНОМ РЕЖИМЕ

Система Механической Трансмиссии 'Multimode' -- Таблица Работы В Аварийном Режиме



ТАБЛИЦА РАБОТЫ В АВАРИЙНОМ РЕЖИМЕ

  1. If any of the following codes is recorded, the TCM enters the fail-safe mode.

    DTC No.
    		Malfunction Areas
    		Fail-safe Functions
    		Fail-safe Deactivation Conditions
    1. P0806
    2. P0807
    3. P0808
    4. P0810
    5. P0900
    1. Clutch stroke sensor or its circuit
    2. Clutch actuator assembly or its circuit
    1. Gear does not change
    2. Vehicle does not start moving again after stopping
    		Either (a) or (b) met:
    1. (a) All of following conditions met:
      1. Pass condition detected
      2. Shift lever in N position
      3. Transaxle gear in neutral*
      4. Vehicle speed less than 6 km/h (3.73 mph)
    2. (b) Pass condition detected and ignition switch off
    1. P0807
    2. P0808
    3. P0906
    4. P0907
    5. P0916
    6. P0917
    1. Clutch stroke sensor or its circuit
    2. Select stroke sensor or its circuit
    3. Shift stroke sensor or its circuit
    		Limit to 3rd gears or lower
    		Either of (a) or (b) met:
    1. (a) All of the following conditions met:
      1. Pass condition detected
      2. Shift lever in N position
      3. Transmission gear in neutral*
      4. Vehicle speed less than 6 km/h (3.73 mph)
    2. (b) Pass condition detected and ignition switch off
    1. P0905
    2. P0906
    3. P0907
    4. P0909
    5. P0910
    6. P0915
    7. P0916
    8. P0917
    9. P0919
    10. P0920
    1. Shift stroke sensor or its circuit
    2. Shift actuator assembly or its circuit
    3. Select stroke sensor or its circuit
    4. Select actuator assembly or its circuit
    1. Gear does not change
    2. Vehicle does not start moving again after stopping
    		Either (a) or (b) met:
    1. (a) All of following conditions met:
      1. Pass condition detected
      2. Shift lever in N position
      3. Vehicle speed less than 6 km/h (3.75 mph)
    2. (b) Pass condition detected and ignition switch off
    P0725
    		Engine speed input circuit
    1. Convert engine revolution signals into CAN communication signals
    2. No effect
    		Either (a) or (b) met:
    1. (a) All of following conditions met:
      1. Pass condition detected
      2. Actual gear position not in neutral
      3. Clutch engaged
    2. (b) Pass condition detected and ignition switch off
    1. P0500
    2. P0715
    1. Vehicle speed sensor or its circuit
    2. Transmission revolution sensor or its circuit
    1. Gear does not shift down while driving
    2. Only possible to drive in 1st or reverse gears after vehicle stops
    		Either (a) or (b) met:
    1. (a) All of following conditions met:
      1. Pass condition detected
      2. Vehicle speed less than 6 km/h (3.73 mph)
      3. Accelerator pedal released
      4. Brake pedal depressed
    2. (b) Pass condition detected and ignition switch off
    1. P0603
    2. P0885
    1. TCM
    2. Clutch actuator, shift actuator, select actuator power source circuit
    1. Gear does not change
    2. Engine cannot be started
    3. TCM stops engine when vehicle stops
    		Pass condition detected and ignition switch off
    P0820
    1. Shift lever position sensor or its circuit
    2. Transmission shift main switch or its circuit
    1. Impossible to enter M-mode
    2. Gear does not shift to 1st or reverse (and forward or backward gears)
    		Pass condition detected and ignition switch off
    P0335
    		Crankshaft position sensor or its circuit
    		Gear does not change
    (Only E ←→ N ←→ R is possible)
    		Pass condition detected and ignition switch off
    U0100
    		CAN communication signal circuit
    1. Gear does not change
    2. Only possible to drive in 1st or reverse gears after vehicle stops
    		Either (a) or (b) met:
    1. (a) All of following conditions met:
      1. Pass condition detected
      2. Vehicle stopped
      3. Accelerator pedal released
      4. Brake pedal depressed
    2. (b) Pass condition detected and ignition switch off

    УКАЗАНИЕ:
    1. *: Transaxle gear: Actual transaxle gear position
    2. The TCM identifies the actual transaxle gear position through the signals from the shift stroke sensor and select stroke sensor.
    3. The TCM identifies the shift lever position through the signal from the shift lever position sensor.