Система Посадки И Запуска Процедура Поиска Неисправностей. Corolla Auris

Двигатель. COROLLA, AURIS. ZZE150 ZRE151,152 NDE150
Система Запуска 2Ad-Fhv. COROLLA, AURIS. ZZE150 ZRE151,152 NDE150

  1. VEHICLE BROUGHT TO WORKSHOP

  2. CUSTOMER PROBLEM ANALYSIS CHECK

  3. INSPECT BATTERY VOLTAGE

  4. INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

  5. CHECK FOR DTC*

  6. INSPECT BASIC OPERATION

  7. ТАБЛИЦА ПРИЗНАКОВ НЕИСПРАВНОСТЕЙ

  8. OVERALL ANALYSIS AND TROUBLESHOOTING*

  9. REPAIR OR REPLACE

  10. CONFIRMATION TEST

Система Посадки И Запуска -- Процедура Поиска Неисправностей


УКАЗАНИЕ:
  1. Use the following procedures to troubleshoot the push-button start function.
  2. *: Use the intelligent tester.


1.VEHICLE BROUGHT TO WORKSHOP

    NEXT


    2.CUSTOMER PROBLEM ANALYSIS CHECK
      УКАЗАНИЕ:
      1. In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
      2. Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
      1. The following 5 items are important points in the problem analysis:

        What
        		Vehicle model, system name
        When
        		Date, time, occurrence frequency
        Where
        		Road conditions
        Under what conditions?
        		Running conditions, driving conditions, weather conditions
        How did it happen?
        		Problem symptoms

    NEXT


    3.INSPECT BATTERY VOLTAGE
      Standard voltage:
      11 to 14 V
      If the voltage is below 11 V, recharge or replace the battery before proceeding.

    NEXT


    4.INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

    1. Use the intelligent tester to check if the CAN Communication System is functioning normally (See page Нажмите здесь).

      Result:
      Result
      		Proceed to
      CAN DTC is not output
      		A
      CAN DTC is output
      		B


    		B.
    GO TO CAN COMMUNICATION SYSTEM
    A


    5.CHECK FOR DTC*

    1. Check for DTCs and note any codes that are output (See page Нажмите здесь).

    2. Delete DTCs.

    3. Recheck for DTCs.

      Result:
      Result
      		Proceed to
      DTC does not reoccur
      		A
      DTC reoccurs
      		B


    		B.
    GO TO DIAGNOSTIC TROUBLE CODE CHART
    A


    6.INSPECT BASIC OPERATION

    1. Turn the engine switch on (START) and check that the engine starts normally. Make sure that the clutch pedal is depressed at this time.

    2. Check that the engine switch mode can be changed by pushing the engine switch.

      УКАЗАНИЕ:
      Without depressing the clutch pedal, push the engine switch repeatedly. Engine switch mode should turn from off to on (ACC) to on (IG) and back to off.
      With the clutch pedal depressed, push the engine switch repeatedly. Engine switch mode should turn to ENGINE START from any status.
      OK:
      Engine can start normally.

    NEXT


    7.ТАБЛИЦА ПРИЗНАКОВ НЕИСПРАВНОСТЕЙ

      Result:

      Result
      		Proceed to
      Fault is not listed in the problem symptoms table
      		A
      Fault is listed in the problem symptoms table
      		B


    		B.
    Go to step 9
    A


    8.OVERALL ANALYSIS AND TROUBLESHOOTING*

    1. Terminals of ECU (See page Нажмите здесь).

    2. DATA LIST/ACTIVE TEST (See page Нажмите здесь).


    NEXT


    9.REPAIR OR REPLACE

      NEXT


      10.CONFIRMATION TEST

        NEXT

        END