Dtc P0014 Camshaft Position B - Timing Over-Advanced Or System Performance (Bank 1). Corolla Auris

Двигатель. COROLLA, AURIS. ZZE150 ZRE151,152 NDE150
Система Управления Двигателем 2Zr-Fe. COROLLA, AURIS. ZZE150 ZRE151,152 NDE150

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0014 OR P0015)

INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

INSPECT OIL CONTROL VALVE FILTER

INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

ADJUST VALVE TIMING

CHECK WHETHER DTC OUTPUT RECURS (DTC P0014 OR P0015)

DTC P0014 Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1)

DTC P0015 Camshaft Position "B" - Timing Over-Retarded (Bank 1)


DESCRIPTION

УКАЗАНИЕ:
If DTC P0014 or P0015 is present, check the VVT (Variable Valve Timing) system.
Refer to DTC P0013 (See page Нажмите здесь).

DTC No.
DTC Detection Condition
Trouble Area
P0014
Advanced cam timing:
With warm engine and engine speed of between 500 rpm and 4000 rpm, all conditions (a), (b) and (c) are met
(2 trip detection logic):
(a) Difference between target and actual exhaust valve timing is more than 5°CA (Crankshaft Angle) for 1 second
(b) Current exhaust valve timing is fixed (timing changes less than 5°CA in 5 seconds)
(c) Variations in VVT controller timing is more than 19°CA of maximum delayed timing (advanced)
  1. Valve timing
  2. Camshaft timing oil control valve assembly for exhaust camshaft
  3. Oil control valve filter
  4. Exhaust camshaft timing gear assembly
  5. ECM
P0015
Retarded cam timing:
With warm engine and engine speed of between 500 rpm and 4000 rpm, all conditions (a), (b) and (c) are met
(1 trip detection logic):
(a) Difference between target and actual exhaust valve timing is more than 5°CA (Crankshaft Angle) for 1 second
(b) Current exhaust valve timing is fixed (timing changes less than 5°CA in 5 seconds)
(c) Variations in VVT controller timing is more than 19°CA or less of maximum delayed timing (retarded)
  1. Valve timing
  2. Camshaft timing oil control valve assembly for exhaust camshaft
  3. Oil control valve filter
  4. Exhaust camshaft timing gear assembly
  5. ECM

WIRING DIAGRAM

Refer to DTC P0010 (See page Нажмите здесь).

INSPECTION PROCEDURE

УКАЗАНИЕ:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0014 OR P0015)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:

    Result
    		Proceed to
    DTC P0014 or P0015 is output
    		A
    DTC P0014 or P0015 and other DTCs are output
    		B
    УКАЗАНИЕ:
    If any DTCs other than P0014 or P0015 are output, troubleshoot those DTCs first.


B
GO TO DTC CHART (Нажмите здесь)
A


2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


    COROLLA, AURIS. ZZE150 ZRE151,152 NDE150.Система Управления Двигателем 2Zr-Fe.Система Sfi. Dtc P0014 Camshaft Position B - Timing Over-Advanced Or System Performance (Bank 1)

  1. Remove the camshaft timing oil control valve assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Condition
    		Specified Condition
    1 - 2
    		20°C (68°F)
    		6.9 to 7.9 Ω


    COROLLA, AURIS. ZZE150 ZRE151,152 NDE150.Система Управления Двигателем 2Zr-Fe.Система Sfi. Dtc P0014 Camshaft Position B - Timing Over-Advanced Or System Performance (Bank 1)

  1. Apply positive battery voltage to terminal 1 and negative battery voltage to terminal 2. Check the valve operation.

    OK:
    Valve moves quickly.

  1. Reinstall the camshaft timing oil control valve assembly.



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Нажмите здесь)
OK


3.INSPECT OIL CONTROL VALVE FILTER
COROLLA, AURIS. ZZE150 ZRE151,152 NDE150

  1. Remove the oil control valve filter.

  1. Check that the filter is not clogged.

    OK:
    Filter is not clogged.

  1. Reinstall the oil control valve filter.



NG
CLEAN OIL CONTROL VALVE FILTER
OK


4.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

  1. Inspect the camshaft timing gear assembly (See page Нажмите здесь).



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (Нажмите здесь)
OK


5.ADJUST VALVE TIMING
УКАЗАНИЕ:
There are no marks on the cylinder head to match-up for the purpose of checking valve timing. Valve timing can only be inspected by lining up the colored plates on the timing chain with the marks on the pulleys. It may be necessary to remove and re-install the chain to match-up the timing marks (See page Нажмите здесь).

NEXT


6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014 OR P0015)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (See page Нажмите здесь).

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the tester.

  1. Drive the vehicle for more than 10 minutes.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Result
    		Proceed to
    DTC is not output
    		A
    DTC P0014 or P0015 is output
    		B
    УКАЗАНИЕ:
    DTC P0014 or P0015 is output when foreign objects in engine oil are caught in some parts of the system. These codes will stay output for a short time even after the system returns to normal. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.


B
REPLACE ECM (Нажмите здесь)
A

SYSTEM IS OK