Remove the manual transmission (See page ).

Place matchmarks on the clutch cover and flywheel.

Loosen each set bolt one turn at a time until spring tension is released.

Remove the 6 set bolts and pull off the clutch cover.

• ПРИМЕЧАНИЕ:

• Do not drop the clutch disc.

Using SST, hold the crankshaft.

• SST
• 09213-54015(91651-60855)
  09330-00021

Remove the 8 bolts and flywheel.

Remove the 2 bolts and rear end plate.

Using a knife, cut off the lip of the oil seal.

Using a screwdriver, pry out the oil seal.

• ПРИМЕЧАНИЕ:

• After the removal, check that the crankshaft is not damaged. If damaged, repair it with a sandpaper (#400).

• УКАЗАНИЕ:

• Tape the screwdriver before use.

Apply MP grease to the lip of a new oil seal.

Using SST and a hammer, tap in the oil seal to a depth of 0.5 mm (0.0197 in.) from the oil pump case edge.

• SST
• 09214-60010

Align the key groove of the timing pulley with the pulley set key.

Using SST and a hammer, tap in the timing pulley with the flange side facing inward.

• SST
• 09223-46011

Install the timing belt (See page ).

Remove the timing belt (See page ).

Using a screwdriver, remove the crankshaft timing pulley.

• SST
• 09950-50013(09951-05010,09952-05010,09953-05010,09953-05020,09954-05010)

• УКАЗАНИЕ:

• If the timing pulley cannot be removed by using a screwdriver, remove it with SST.

Using a knife, cut off the lip of the oil seal.

Using a screwdriver, pry out the oil seal.

• ПРИМЕЧАНИЕ:

• Do not damage the crankshaft.

• ПРИМЕЧАНИЕ:

• Tape the screwdriver before use.

Check the piston protrusion for each cylinder.

Find where the piston head protrudes most by slowly turning the crankshaft clockwise and counterclockwise.

Text in Illustration

*a	Measuring Tip
*b	Protrusion

Measure the protrusion of each cylinder at 2 places as shown in the illustration, making a total of 8 measurements.

Text in Illustration

*a	Measuring Point
	Front

For the piston protrusion value of each cylinder, use the average of the 2 measurements of that cylinder.

• Standard protrusion:
• 0.68 to 0.98 mm (0.0268 to 0.0386 in.)

After installing the piston and connecting rod assembly, if the protrusion is not as specified, remove the piston and connecting rod assembly and reinstall them.

Select a new cylinder head gasket.

Text in Illustration

*1	Cutout Mark
	Front

• УКАЗАНИЕ:

• There are 3 sizes of new cylinder head gaskets, marked "B", "D" or "F" accordingly.

• New Cylinder Head Gasket Thickness:

• Item	Specified Condition
  Mark B	1.40 to 1.50 mm (0.0551 to 0.0591 in.)
  Mark D	1.50 to 1.60 mm (0.0591 to 0.0630 in.)
  Mark F	1.60 to 1.70 mm (0.0630 to 0.0669 in.)

Install the selected cylinder head gasket to the cylinder block.

• ПРИМЕЧАНИЕ:

• Make sure that the gasket is installed facing the proper direction.

• Be careful of the installation direction.

Using the crankshaft pulley bolt, turn the crankshaft 90° counterclockwise, and align the timing mark of the crankshaft timing pulley with the protrusion of the timing belt case.

Text in Illustration

Turn

Place the cylinder head on the cylinder block.

• ПРИМЕЧАНИЕ:

Install the plate washers to the cylinder head bolts.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.

Step 1:

Install and uniformly tighten the 18 cylinder head bolts, in several steps, in the sequence shown in the illustrations.

• Момент затяжки:
• 78 N*m{ 795 kgf*cm, 58 ft.*lbf}

• УКАЗАНИЕ:

• Each bolt length is indicated below.

• Standard Bolt:

• Item	Length
  Bolt A	107 mm (4.21 in.)
  Bolt B	127 mm (5.00 in.)

If any one of the cylinder head bolts does not meet the torque specification, replace the cylinder set head bolt.

Step 2:

Step 3:

Check that the paint marks are now at a 180° angle to the front.

Remove the 9 bolts, nut, cylinder head cover and gasket.

Install the wiring harness clamp bracket with the bolt.

• Момент затяжки:
• 22 N*m{ 219 kgf*cm, 16 ft.*lbf}

Connect the engine wire and install the No. 2 glow plug resistor insulator and washer with the nut.

• Момент затяжки:
• 5.0 N*m{ 51 kgf*cm, 44 in.*lbf}

Attach the 4 wire harness clamps.

Install the generator wire with the nut.

• Момент затяжки:
• 9.8 N*m{ 100 kgf*cm, 87 in.*lbf}

Install the terminal cap.

Connect the generator connector and cooler compressor connector.

for RHD:

Attach the 5 wire harness clamps.

for LHD:

Attach the 4 wire harness clamps.

Attach the 3 wire harness clamps.

Install the 2 lower clamps to the intake manifold.

Install the 4 injection pipes.

• Момент затяжки:
• 25 N*m{ 250 kgf*cm, 18 ft.*lbf}

• ПРИМЕЧАНИЕ:

• Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page ).

Install the 2 upper pipe clamps with the 2 nuts.

• Момент затяжки:
• 5.0 N*m{ 51 kgf*cm, 44 in.*lbf}

Connect the 2 water hoses.

Install the heater water hose clamp with the bolt.

• Момент затяжки:
• 14 N*m{ 138 kgf*cm, 10 ft.*lbf}

Установите теплозащитный экран и закрепите его 3 болтами.

• Момент затяжки:
• Для болта A:
• 18 N*m{ 185 kgf*cm, 13 ft.*lbf}
• для болта B:
• 19 N*m{ 195 kgf*cm, 14 ft.*lbf}

Apply a light coat of engine oil to a new O-ring.

Install the O-ring to the dipstick guide.

Install the dipstick guide with the 2 bolts.

• Момент затяжки:
• 18 N*m{ 184 kgf*cm, 13 ft.*lbf}

Install the dipstick.

Install the No. 1 compressor mounting bracket with the 4 bolts.

• Момент затяжки:
• 81 N*m{ 829 kgf*cm, 60 ft.*lbf}

Connect the generator with the bolt.

Temporarily install the cooler compressor with the 2 bolts.

Temporarily install the idle pulley bracket with the 4 bolts.

Tighten the 6 bolts in the sequence shown in the illustration.

• Момент затяжки:
• for bolt A:
• 45 N*m{ 459 kgf*cm, 33 ft.*lbf}
• except bolt A:
• 25 N*m{ 250 kgf*cm, 18 ft.*lbf}

Connect the wire harness with the bolt.

• Момент затяжки:
• 13 N*m{ 131 kgf*cm, 9 ft.*lbf}

Connect the cooler compressor connector.

Install the diesel throttle body (See page ).

Install the timing belt (See page ).

Install a new gasket and the front exhaust pipe to the exhaust manifold with 3 new nuts.

• Момент затяжки:
• 54 N*m{ 554 kgf*cm, 40 ft.*lbf}

Install the No. 1 exhaust pipe support bracket with the 2 bolts.

• Момент затяжки:
• 71 N*m{ 724 kgf*cm, 52 ft.*lbf}

Install the clamp with the bolt.

• Момент затяжки:
• 19 N*m{ 194 kgf*cm, 14 ft.*lbf}

Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

Затяните пробку сливного крана радиатора вручную.

Затяните пробку сливного крана блока цилиндров.

• Момент затяжки:
• 13 N*m{ 130 kgf*cm, 9 ft.*lbf}

Медленно заполните систему охлаждающей жидкостью двигателя.

• Номинальный объем:
• 8,6 литра (9,0 кварты США, 7,6 английской кварты)

• ПРИМЕЧАНИЕ:

• Не доливайте простую воду вместо охлаждающей жидкости двигателя.

• УКАЗАНИЕ:

Медленно залейте охлаждающую жидкость в расширительный бачок радиатора до отметки "FULL".

Установите пробку расширительного бачка.

Несколько раз сожмите рукой патрубки радиатора № 1 и № 2, а затем проверьте уровень охлаждающей жидкости. Если уровень охлаждающей жидкости недостаточен, добавьте жидкость.

Установите на место пробку радиатора.

Запустите двигатель и прогрейте его до открывания термостата.

• УКАЗАНИЕ:

• Время открывания термостата можно распознать, сжав шланг радиатора № 2 рукой и отметив момент, когда охлаждающая жидкость двигателя начнет поступать в шланг.

Поддерживайте частоту вращения коленчатого вала двигателя 2000–2500 об/мин.

• ПРИМЕЧАНИЕ:

Несколько раз сожмите патрубки радиатора № 1 и № 2 рукой, чтобы удалить воздух.

• ПРЕДОСТЕРЕЖЕНИЕ:

Остановите двигатель и подождите, пока охлаждающая жидкость остынет до температуры окружающего воздуха.

• ПРЕДОСТЕРЕЖЕНИЕ:

• Не снимайте пробку радиатора, пока двигатель и радиатор не остынут. Выброс горячей охлаждающей жидкости и пара под давлением может стать причиной серьезных ожогов.

Убедитесь, что уровень охлаждающей жидкости находится между отметками "LOW" и "FULL".

Если уровень охлаждающей жидкости ниже линии "Low", повторите все вышеперечисленные действия.

Если уровень охлаждающей жидкости выше уровня "FULL", слейте охлаждающую жидкость до уровня между отметками "FULL" и "LOW".

Move the hand pump on the upper part of the fuel filter up and down and fill the injection pump and fuel system with fuel.

Loosen one of the union nuts (on the nozzle side).

Crank the engine until fuel comes out from the union nut connection (on the nozzle side).

Tighten the union nut.

• Момент затяжки:
• 25 N*m{ 250 kgf*cm, 18 ft.*lbf}

• ПРИМЕЧАНИЕ:

• Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page ).

Perform the procedures above for each injection pipe.

Fill the radiator with coolant and attach a radiator cap tester to the radiator.

Warm up the engine.

Using a radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm², 18 psi), and check that the pressure does not drop.

If the pressure drops, check the hoses, radiator or water pump for leaks. If no external leaks are found, check the heater core, cylinder block, and cylinder head.

Check that there are no fuel leaks anywhere in the fuel system after performing maintenance.

• УКАЗАНИЕ:

• When checking for fuel leaks, make sure that there is pressure in the fuel line.

Warm up the engine.

When using the intelligent tester:

When not using an intelligent tester:

Start the engine.

Fully depress the accelerator pedal.

Check the maximum speed.

• Maximum engine speed:
• 4850 to 4950 rpm

Remove the exhaust manifold (See page ).

Remove the timing belt (See page ).

Remove the diesel throttle body (See page ).

Remove the 4 bolts and idle pulley bracket.

Disconnect the connector.

Remove the 3 bolts and disconnect the cooler compressor.

• УКАЗАНИЕ:

• It is not necessary to completely remove the cooler compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.

Remove the bolt and disconnect the generator.

Remove the 4 bolts and No. 1 compressor mounting bracket.

Remove the bolt and disconnect the heater water hoses.

Using a union nut wrench, loosen the 8 union nuts of the 4 injection pipes.

Remove the 2 nuts, 2 upper pipe clamps and 4 injection pipes with 2 lower pipe clamps.

Remove the terminal cap.

Remove the nut and generator wire.

Disconnect the generator connector and cooler compressor connector.

Detach the 4 wire harness clamps.

for RHD:

Detach the 5 wire harness clamps.

for LHD:

Detach the 4 wire harness clamps.

Detach the 3 wire harness clamps.

Remove the bolt and wiring harness clamp bracket.

Remove the 9 bolts, nut, cylinder head cover and gasket.

Turn the camshaft with a wrench so that the key groove faces upward.

Uniformly loosen and remove the 10 bearing cap bolts in several steps in the sequence shown in the illustration.

Remove the 5 bearing caps and camshaft.

• УКАЗАНИЕ:

• Arrange the bearing caps in the correct order.

Uniformly loosen and remove the 18 cylinder head bolts in several steps in the sequence shown.

• ПРИМЕЧАНИЕ:

• Head warpage or cracking could result from removing bolts in an incorrect order.

Lift the cylinder head from the dowels on the cylinder block to remove it, and place the cylinder head on wooden blocks on a workbench.

• ПРИМЕЧАНИЕ:

• Do not damage the contact surfaces of the cylinder head and cylinder block.

• УКАЗАНИЕ:

• If the cylinder head is difficult to lift off, pry between the cylinder head and block with a screwdriver.

Using a vernier caliper, measure the minimum outer diameter of the elongated thread at the measuring point.

• Standard outer diameter:
• 11.80 to 12.00 mm (0.465 to 0.472 in.)

• Minimum outer diameter:
• 11.60 mm (0.457 in.)

If the diameter is less than the minimum, replace the cylinder head set bolt.

Check that the timing mark of the crankshaft timing pulley is in the position shown in the illustration.

Install the camshaft.

Place the camshaft on the cylinder head with the key groove facing upward.

Install the 5 bearing caps in their proper locations.

Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

Install and uniformly tighten the 10 bearing cap bolts in several steps in the sequence shown in the illustration.

• Момент затяжки:
• 25 N*m{ 255 kgf*cm, 18 ft.*lbf}

Using SST and a hammer, tap in a new oil seal until its surface is flush with the oil seal retainer edge.

• SST
• 09960-10010(09962-01000,09963-01000)

Apply MP grease to the lip of the oil seal.

Install a new gasket and the retainer with the 4 bolts.

• Момент затяжки:
• 18 N*m{ 184 kgf*cm, 13 ft.*lbf}

Install the timing belt cover with the 4 bolts.

• Момент затяжки:
• 18 N*m{ 184 kgf*cm, 13 ft.*lbf}

Install the woodruff key to the key groove of the camshaft.

Align the timing mark on the camshaft timing pulley with the timing mark on the No. 2 timing belt cover and temporarily install the pulley with the bolt.

Using SST, tighten the bolt.

• SST
• 09960-10010(09962-01000,09963-01000)

• Момент затяжки:
• 98 N*m{ 999 kgf*cm, 72 ft.*lbf}

Using the crankshaft pulley bolt, align the groove of the crankshaft pulley with the timing pointer by turning the crankshaft clockwise.

Text in Illustration

*1	Timing Mark
	Turn

• ПРИМЕЧАНИЕ:

• Do not turn the crankshaft pulley counterclockwise.

Set the timing and drive pulleys at each position.

• ПРИМЕЧАНИЕ:

Remove any oil or water on each pulley, and keep them clean.

Install the timing belt to the crankshaft timing and timing belt idlers.

Using SST, slightly turn the injection pump drive pulley clockwise. Install the timing belt to the pulley, and align the timing marks of the drive pulley and timing belt case.

• SST
• 09960-10010(09962-01000,09963-01000)

Using SST, slightly turn the camshaft timing pulley clockwise. Install the timing belt to the timing pulley, and align the timing marks of the timing pulley and timing belt case.

• SST
• 09960-10010(09962-01000,09963-01000)

Check that the timing belt has tension between the injection pump drive and camshaft timing pulleys.

Install the timing belt to the No. 1 timing belt idler.

Loosen the No. 1 timing belt idler bolt (A), and stretch the timing belt.

Slowly turn the crankshaft pulley.

• ПРИМЕЧАНИЕ:

• Always turn the crankshaft clockwise.

Tighten the No. 1 timing belt idler bolt.

• Момент затяжки:
• 44 N*m{ 449 kgf*cm, 33 ft.*lbf}

Slowly turn the crankshaft pulley 2 revolutions from TDC to TDC.

• ПРИМЕЧАНИЕ:

• Always turn the crankshaft clockwise.

Check that the timing marks for each pulley align as shown in the illustration.

If the timing marks do not align, remove the timing belt and reinstall it.

Install the timing belt guide with the cup side facing outward.

Check only the valves indicated in the illustration.

Turn the crankshaft 1 revolution (360°) and align the mark as above.

Check only the valves indicated in the illustration.

Remove the adjusting shim.

Turn the crankshaft so that the cam lobe of the camshaft on the valve being adjusted points upward.

Using SST, press down the valve lifter.

• SST
• 09248-64011

Position the notch of the valve lifter so that it faces the exhaust manifold side.

Remove the adjusting shim with a screwdriver and magnet hand.

Determine the replacement adjusting shim size according to the formula and charts below.

Install a new adjusting shim.

Recheck valve clearance.

Remove any old packing (FIPG material).

Apply seal packing to the cylinder head as shown in the illustration.

• Seal packing:
• Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

Install the gasket to the cylinder head cover.

Install the cylinder head cover with the 9 bolts and nut. Uniformly tighten the bolts and nut in several steps.

• Момент затяжки:
• 12 N*m{ 122 kgf*cm, 9 ft.*lbf}

Install the intake pipe with the 2 bolts.

• Момент затяжки:
• 18 N*m{ 184 kgf*cm, 13 ft.*lbf}

Tighten the intake pipe clamp.

• Момент затяжки:
• 6.0 N*m{ 61 kgf*cm, 53 in.*lbf}

Install 2 new gaskets to the timing belt cover.

Install the timing belt cover with the 11 bolts and washers.

• Момент затяжки:
• for bolt A:
• 8.5 N*m{ 85 kgf*cm, 75 ft.*lbf}
• except bolt A:
• 11 N*m{ 107 kgf*cm, 8 ft.*lbf}

Install the idle pulley bracket with the 2 bolts.

• Момент затяжки:
• 29 N*m{ 300 kgf*cm, 22 ft.*lbf}

Align the key groove of the pulley with the pulley set key, and slide the pulley onto the crankshaft to install it.

Using SST, install the pulley bolt.

• SST
• 09213-54015(91651-60855)
  09330-00021

• Момент затяжки:
• 235 N*m{ 2396 kgf*cm, 173 ft.*lbf}

Install the vane pump drive pulley and cooler compressor drive pulley with the 4 bolts.

• Момент затяжки:
• 19 N*m{ 194 kgf*cm, 14 ft.*lbf}

Install the fan pulley to the water pump.

Install the shroud together with the coupling fan between the radiator and engine.

• ПРИМЕЧАНИЕ:

• Be careful not to damage the radiator core.

Temporarily install the fluid coupling fan to the fan pulley with the 4 nuts. Tighten the nuts as much as possible by hand.

Attach the claws of the shroud as shown in the illustration.

Install the shroud with the 2 bolts.

• Момент затяжки:
• 5.0 N*m{ 51 kgf*cm, 44 in.*lbf}

Install the fan and generator V belt and vane pump V belt (See page ).

Tighten the 4 nuts of the fluid coupling fan.

• Момент затяжки:
• 19 N*m{ 189 kgf*cm, 14 ft.*lbf}

Install the radiator reservoir with the 3 bolts.

• Момент затяжки:
• 5.0 N*m{ 51 kgf*cm, 44 in.*lbf}

Connect the radiator reservoir hose to the radiator tank side.

Install the hose clamp with the 2 nuts.

• Момент затяжки:
• 8.5 N*m{ 87 kgf*cm, 75 in.*lbf}

Install the radiator hose.

• УКАЗАНИЕ:

• Position the hose clamps as shown in the illustration.

Install the wiring harness clamp bracket with the bolt.

• Момент затяжки:
• 22 N*m{ 219 kgf*cm, 16 ft.*lbf}

Attach the 4 wire harness clamps.

Install the generator wire with the nut.

• Момент затяжки:
• 9.8 N*m{ 100 kgf*cm, 87 in.*lbf}

Install the terminal cap.

Connect the generator connector and cooler compressor connector.

for LHD:

Attach the 4 wire harness clamps.

Install the air cleaner case with the 3 bolts.

• Момент затяжки:
• 12 N*m{ 122 kgf*cm, 9 ft.*lbf}

Вставьте петли крышки воздушного фильтра и шланг в корпус воздушного фильтра, а затем закрепите 4 откидных защелки.

Установите крышку воздушного фильтра и закрепите ее зажимом.

• Момент затяжки:
• 5,0 N*m{ 51 kgf*cm, 44 in.*lbf}

Закрепите зажим жгута проводов.

Подсоедините 2 зажима и разъем.

Install the front fender apron seal with the 4 clips.

Затяните пробку сливного крана радиатора вручную.

Затяните пробку сливного крана блока цилиндров.

• Момент затяжки:
• 13 N*m{ 130 kgf*cm, 9 ft.*lbf}

Медленно заполните систему охлаждающей жидкостью двигателя.

• Номинальный объем:
• 8,6 литра (9,0 кварты США, 7,6 английской кварты)

• ПРИМЕЧАНИЕ:

• Не доливайте простую воду вместо охлаждающей жидкости двигателя.

• УКАЗАНИЕ:

Медленно залейте охлаждающую жидкость в расширительный бачок радиатора до отметки "FULL".

Установите пробку расширительного бачка.

Несколько раз сожмите рукой патрубки радиатора № 1 и № 2, а затем проверьте уровень охлаждающей жидкости. Если уровень охлаждающей жидкости недостаточен, добавьте жидкость.

Установите на место пробку радиатора.

Запустите двигатель и прогрейте его до открывания термостата.

• УКАЗАНИЕ:

• Время открывания термостата можно распознать, сжав шланг радиатора № 2 рукой и отметив момент, когда охлаждающая жидкость двигателя начнет поступать в шланг.

Поддерживайте частоту вращения коленчатого вала двигателя 2000–2500 об/мин.

• ПРИМЕЧАНИЕ:

Несколько раз сожмите патрубки радиатора № 1 и № 2 рукой, чтобы удалить воздух.

• ПРЕДОСТЕРЕЖЕНИЕ:

Остановите двигатель и подождите, пока охлаждающая жидкость остынет до температуры окружающего воздуха.

• ПРЕДОСТЕРЕЖЕНИЕ:

• Не снимайте пробку радиатора, пока двигатель и радиатор не остынут. Выброс горячей охлаждающей жидкости и пара под давлением может стать причиной серьезных ожогов.

Убедитесь, что уровень охлаждающей жидкости находится между отметками "LOW" и "FULL".

Если уровень охлаждающей жидкости ниже линии "Low", повторите все вышеперечисленные действия.

Если уровень охлаждающей жидкости выше уровня "FULL", слейте охлаждающую жидкость до уровня между отметками "FULL" и "LOW".

Fill the radiator with coolant and attach a radiator cap tester to the radiator.

Warm up the engine.

Using a radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm², 18 psi), and check that the pressure does not drop.

If the pressure drops, check the hoses, radiator or water pump for leaks. If no external leaks are found, check the heater core, cylinder block, and cylinder head.

Warm up the engine.

When using the intelligent tester:

When not using an intelligent tester:

Start the engine.

Fully depress the accelerator pedal.

Check the maximum speed.

• Maximum engine speed:
• 4850 to 4950 rpm

Hook the engine under cover to the vehicle body as shown in the illustration.

Install the 4 bolts.

• Момент затяжки:
• 29 N*m{ 296 kgf*cm, 21 ft.*lbf}

Install the front bumper cover lower with the 5 bolts and clip.

• Момент затяжки:
• 8.0 N*m{ 82 kgf*cm, 71 in.*lbf}

Установите верхнее уплотнение кронштейна радиатора и закрепите его 13 фиксаторами.

Освободите 13 фиксаторов и снимите верхнее уплотнение кронштейна радиатора.

Remove the clip, 5 bolts and front bumper cover lower.

Remove the 4 bolts.

Unhook the engine under cover from the vehicle body as shown in the illustration.

Ослабьте пробку сливного крана радиатора.

• УКАЗАНИЕ:

• Слейте охлаждающую жидкость в контейнер и утилизируйте ее в соответствии с местными требованиями.

Слейте охлаждающую жидкость, сняв крышку радиатора.

Ослабьте пробку сливного крана блока цилиндров.

Ослабьте пробку сливного крана блока цилиндров и слейте охлаждающую жидкость из двигателя.

• ПРИМЕЧАНИЕ:

• Если охлаждающая жидкость не сливается через пробку сливного крана радиатора, пробки сливных кранов блока цилиндров и расширительный бачок радиатора, возможны засорение радиатора и утечка охлаждающей жидкости через уплотнение насоса системы охлаждения.

Remove the 4 clips and fender apron seal.

Disconnect the sensor connector.

Detach the wire harness clamp.

Loosen the hose clamp and remove the resonator with air cleaner cap.

Detach the 4 hook clamps, and then remove the air cleaner cap and resonator with air cleaner cap.

Remove the 3 bolts and air cleaner case.

Remove the terminal cap.

Remove the nut and generator wire.

Disconnect the generator connector and cooler compressor connector.

Detach the 4 wire harness clamps.

for LHD:

Detach the 4 wire harness clamps.

Remove the bolt and wiring harness clamp bracket.

Detach the clamp and remove the No. 1 radiator hose.

Remove the 2 nuts and hose clamp.

Disconnect the reservoir hose from the upper side of the radiator tank.

Remove the 3 bolts and radiator reservoir.

Loosen the 4 nuts holding the fluid coupling fan.

Remove the vane pump V belt and the fan and generator V belt (See page ).

Remove the 2 bolts holding the fan shroud.

Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

• ПРИМЕЧАНИЕ:

• Be careful not to damage the radiator core.

Remove the fan pulley from the water pump.

Remove the 4 bolts, vane pump drive pulley and cooler compressor drive pulley.

Using SST, remove the pulley bolt.

• SST
• 09213-54015(91651-60855)
  09330-00021

Using SST, remove the pulley.

• SST
• 09950-50013(09951-05010,09952-05010,09953-05020,09954-05021)
  09950-60010(09951-00490)
  09950-40011(09957-04010)

Remove the 2 bolts and Idle pulley bracket.

Remove the 11 bolts, washers, timing belt cover, and 2 gaskets.

Remove the timing belt guide.

Using the crankshaft pulley bolt, align the groove of the crankshaft pulley with the timing pointer by turning the crankshaft clockwise.

Text in Illustration

*1	Timing Mark
	Turn

Check that the timing marks of the camshaft timing pulley and No. 2 timing belt cover are aligned.

If not, turn the crankshaft 1 revolution (360°).

Turn the crankshaft 90° counterclockwise, and align the timing mark of the crankshaft timing pulley with the protrusion of the timing belt case.

Text in Illustration

Turn

• ПРИМЕЧАНИЕ:

• If the timing belt is disengaged, having the crankshaft timing pulley at the wrong angle can cause the piston head and valve head to come into contact with each other when removing the camshaft timing pulley, and camshaft causing damage. Therefore, always set the crankshaft pulley is removed at the correct angle.

Loosen the No. 1 timing belt idler bolt (A), and shift the idler to the left as far as possible.

Text in Illustration

	Pry
	Move

Tighten the No. 1 timing belt idler bolt (A), and then relieve the timing belt tension.

Remove the timing belt.

Loosen the hose clamp and remove the 2 bolts and intake pipe.

Remove the 9 bolts, nut, cylinder head cover and gasket.

Using the crankshaft pulley bolt, turn the crankshaft 90° counterclockwise and align the timing mark of the crankshaft timing pulley with the protrusion of the timing belt case.

Text in Illustration

	Turn
*1	Timing Mark
*2	Protrusion

• УКАЗАНИЕ:

• Set the No. 1 cylinder to 90° BTDC/compression to avoid interference with the piston top and valve head.

Using SST, loosen the pulley bolt.

• SST
• 09960-10010(09962-01000,09963-01000)

Using SST, separate the timing pulley from the camshaft.

• SST
• 09950-50013(09951-05010,09952-05010,09953-05010,09954-05021)

Remove the pulley bolt and timing pulley.

Remove the timing pulley woodruff key.

Remove the 4 bolts and timing belt cover.

Remove the 4 bolts, retainer and gasket.

Using a screwdriver and hammer, tap out the oil seal.

Turn the camshaft with a wrench so that the key groove faces upward.

Uniformly loosen and remove the 10 bearing cap bolts in several steps in the sequence shown in the illustration.

Remove the 5 bearing caps and camshaft.

• УКАЗАНИЕ:

• Arrange the bearing caps in the correct order.