Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - SUPPLEMENTAL RESTRAINT SYSTEMS
REAR AIRBAG SENSOR - REMOVAL
- HINT:
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected ().
| 2. REMOVE REAR NO. 2 SEAT ASSEMBLY LH |
Remove the rear No. 2 seat assembly LH ().
| 3. REMOVE REAR NO. 2 SEAT ASSEMBLY LH (for Split Bench Seat Type) |
Remove the rear No. 2 seat assembly LH ().
| 4. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/ Sliding Roof) |
Detach the 6 clips and remove the support plate.
| 5. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/o Sliding Roof) |
Detach the 6 clips and remove the support plate.
| 6. REMOVE REAR STEP COVER (w/ Sliding Roof) |
- HINT:
- Use the same procedure to remove the step cover on the other side.
Detach the 2 claws and remove the step cover.
| 7. REMOVE REAR STEP COVER (w/o Sliding Roof) |
- HINT:
- Use the same procedure to remove the step cover on the other side.
Detach the 2 claws and remove the step cover.
| 8. REMOVE REAR DOOR SCUFF PLATE LH (w/ Sliding Roof) |
Remove the screw.
Detach the 3 claws and 4 clips, and remove the scuff plate.
| 9. REMOVE REAR DOOR SCUFF PLATE LH (w/o Sliding Roof) |
Remove the screw.
Detach the 3 claws and 4 clips, and remove the scuff plate.
| 10. REMOVE REAR SEAT COVER CAP (w/ Sliding Roof) |
- HINT:
- Use the same procedure to remove the rear seat cover cap on the other side.
Using a screwdriver, detach the 3 claws and remove the rear seat cover cap.
- HINT:
- Tape the screwdriver tip before use.
| 11. REMOVE REAR SEAT COVER CAP (w/o Sliding Roof) |
- HINT:
- Use the same procedure to remove the rear seat cover cap on the other side.
Using a screwdriver, detach the 3 claws and remove the rear seat cover cap.
- HINT:
- Tape the screwdriver tip before use.
| 12. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH (w/ Sliding Roof) |
- HINT:
- When removing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.
Detach the 3 claws and remove the cover.
Remove the bolt and rear No. 1 seat belt anchor.
w/ Rear No. 2 Seat, except Face to Face Seat Type:
Remove the bolt and rear No. 2 seat belt anchor.
w/ Rear No. 2 Seat, except Face to Face Seat Type:
Remove the clip and bolt.
Detach the 18 clips and 2 claws.
w/o Rear Air Conditioning System:
Disconnect the rear seat lock control lever cable and then remove the quarter trim panel.
w/ Rear Air Conditioning System:
Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the quarter trim panel.
w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:
Remove the clip.
Detach the 18 clips and 2 claws, and remove the quarter trim panel.
| 13. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH (w/o Sliding Roof) |
- HINT:
- When removing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.
Detach the 3 claws and remove the cover.
Remove the bolt and rear No. 1 seat belt anchor.
w/ Rear No. 2 Seat, except Face to Face Seat Type:
Remove the bolt and rear No. 2 seat belt anchor.
w/ Rear No. 2 Seat, except Face to Face Seat Type:
Remove the clip and bolt.
Detach the 18 clips and 2 claws.
w/o Rear Air Conditioning System:
Disconnect the rear seat lock control lever cable and then remove the quarter trim panel.
w/ Rear Air Conditioning System:
Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the quarter trim panel.
w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:
Remove the clip.
Detach the 18 clips and 2 claws, and remove the quarter trim panel.
w/ Tonneau Cover:
Remove the screw and clip.
Detach the 18 clips and 2 claws, and remove the quarter trim panel.
| 14. REMOVE REAR AIRBAG SENSOR |
Remove the bolt and rear airbag sensor.
Disconnect the connector.