Rear Seat Side Airbag Assembly - Disposal

Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - SUPPLEMENTAL RESTRAINT SYSTEMS

REAR SEAT SIDE AIRBAG ASSEMBLY - DISPOSAL

  • HINT:
  • When scrapping a vehicle equipped with the SRS or disposing of the steering pad, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the SERVICE DEPT. of the DISTRIBUTOR.
  • CAUTION:
Never dispose of a rear seat side airbag that has an unactivated airbag.
The airbag produces an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.
When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.
When deploying the airbag, perform the operation at least 10 m (32.8 ft.) away from the airbag.
The rear seat side airbag becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
Use gloves and safety glasses when handling a rear seat side airbag with a deployed airbag.
Do not apply water to a rear seat side airbag with a deployed airbag.
Always wash your hands with water after completing the operation.
An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with bare hands to discharge static electricity before performing this procedure.
1. DISPOSE OF REAR SEAT SIDE AIRBAG ASSEMBLY (WHEN INSTALLED IN VEHICLE)
  • HINT:
  • Prepare a battery as the power source to deploy the airbag.
Rear Seat Side Airbag Assembly - Disposal. SUPPLEMENTAL RESTRAINT SYSTEMS. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Check the function of SST ().

Read the precaution ().

Disconnect the cable from the negative (-) battery terminal.

  • CAUTION:
  • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
  • NOTICE:
  • When disconnecting the cable, some systems need to be initialized after the cable is reconnected ().

Remove the rear seat ().

  • HINT:
  • Keep the rear seat in the cabin.
Rear Seat Side Airbag Assembly - Disposal. SUPPLEMENTAL RESTRAINT SYSTEMS. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install SST.

Disconnect the connector (yellow colored) from the rear seat side airbag.

  • NOTICE:
  • When handling the airbag connector, take care not to damage the airbag wire harness.

Connect SST connector to the rear seat side airbag connector.

  • SST
  • 09082-00700
    09082-00820
  • NOTICE:
  • To avoid damaging SST connector and wire harness, do not lock the secondary lock of the twin lock.

Install the rear seat ().

Rear Seat Side Airbag Assembly - Disposal. SUPPLEMENTAL RESTRAINT SYSTEMS. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Move SST at least 10 m (32.8 ft.) away from the vehicle front side window.

Maintaining enough clearance for SST wire harness in the front side window, close all doors and windows of the vehicle.

  • NOTICE:
  • Take care not to damage SST wire harness.

Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the battery negative (-) terminal.

Deploy the airbag.

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.

Press SST activation switch to deploy the airbag.

  • CAUTION:
When deploying the airbag, make sure that no one is near the vehicle.
The rear seat side airbag becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
Use gloves and safety glasses when handling a rear seat side airbag with a deployed airbag.
Do not apply water to a rear seat side airbag with a deployed airbag.
Always wash your hands with water after completing the operation.
  • HINT:
  • The airbag is deployed as the LED of SST activation switch comes on.
2. DISPOSE OF REAR SEAT SIDE AIRBAG ASSEMBLY (WHEN NOT INSTALLED IN VEHICLE)
  • NOTICE:
  • Be sure to follow the procedure detailed below when deploying the airbag.
  • HINT:
  • Prepare a battery as the power source to deploy the airbag.
Rear Seat Side Airbag Assembly - Disposal. SUPPLEMENTAL RESTRAINT SYSTEMS. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Check the function of SST ().

Remove the rear seat side airbag.

Remove the rear seat ().

Remove the 2 nuts and the rear seat side airbag from the seatback.

  • CAUTION:
When removing the rear seat airbag, wait at least 90 seconds after the ignition switch is turned off and the cable is disconnected from the negative (-) battery terminal before starting work.
When storing the rear seat side airbag, keep the airbag deployment side facing upward.
Rear Seat Side Airbag Assembly - Disposal. SUPPLEMENTAL RESTRAINT SYSTEMS. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using a service-purpose wire harness for the vehicle, tie down the rear seat side airbag to a tire.

  • Cross-sectional area of stripped wire harness section:
  • 1.25 mm2 (0.00192 in.2) or more
  • HINT:
  • To calculate the cross-sectional area of the stripped wire harness section:
  • Cross-sectional area = 3.14 x (Diameter)2 divided by 4
  • CAUTION:
  • If the wire harness is too thin or an alternative object is used to tie down the rear seat side airbag, it may be snapped by the shock when the airbag is deployed. Always use a wire harness for vehicle use with a cross-sectional area of at least 1.25 mm2 (0.00192 in.2).

Rear Seat Side Airbag Assembly - Disposal. SUPPLEMENTAL RESTRAINT SYSTEMS. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the 2 nuts to the rear seat side airbag.

Rear Seat Side Airbag Assembly - Disposal. SUPPLEMENTAL RESTRAINT SYSTEMS. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Wind the wire harness around the stud bolts of the rear seat side airbag as shown in the illustration.

Rear Seat Side Airbag Assembly - Disposal. SUPPLEMENTAL RESTRAINT SYSTEMS. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Position the rear seat side airbag inside a tire.

  • Tire size:
  • Must exceed the following dimensions
  • Width:
  • 185 mm (7.28 in.)
  • Inner diameter:
  • 360 mm (14.2 in.)
  • CAUTION:
Make sure that the wire harnesses are tight. If there is slack in the wire harnesses, the rear seat side airbag may become loose due to the shock when the airbag is deployed.
Always tie down the rear seat side airbag with the airbag deployment direction facing inside the tire.
  • NOTICE:
  • As the tire may be damaged by the airbag deployment, use a tire that you are planning to throw away.
Rear Seat Side Airbag Assembly - Disposal. SUPPLEMENTAL RESTRAINT SYSTEMS. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install SST.

Connect SST connector to the rear seat side airbag connector.

  • SST
  • 09082-00820
Rear Seat Side Airbag Assembly - Disposal. SUPPLEMENTAL RESTRAINT SYSTEMS. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Place tires.

Place at least 2 tires under the tire which the rear seat side airbag is tied to.

Place at least 2 tires over the tire which the rear seat side airbag is tied to. The top tire should have a disc wheel installed.

  • NOTICE:
Do not place SST connector under the tire because it could be damaged.
As the disc wheel may be damaged by the airbag deployment, use a disc wheel that you are planning to throw away.
As the tires may be damaged by the airbag deployment, use tires that you are planning to throw away.
Rear Seat Side Airbag Assembly - Disposal. SUPPLEMENTAL RESTRAINT SYSTEMS. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Tie the tires together with 2 wire harnesses.

  • CAUTION:
  • Make sure that the wire harnesses are tight. Looseness in the wire harnesses results in the tires coming free due to the shock when the airbag is deployed.
Rear Seat Side Airbag Assembly - Disposal. SUPPLEMENTAL RESTRAINT SYSTEMS. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install SST.

Connect SST connector.

  • SST
  • 09082-00700
  • NOTICE:
  • To avoid damaging SST connector and wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for SST wire harness inside the tire.

Deploy the airbag.

Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the battery negative (-) terminal.

Check that no one is within a 10 m (32.8 ft.) radius of the tire which the rear seat side airbag is tied to.

Press SST activation switch to deploy the airbag.

  • CAUTION:
  • When deploying the airbag, make sure that no one is near the tire.
  • HINT:
  • The airbag is deployed as the LED of SST activation switch comes on.
Rear Seat Side Airbag Assembly - Disposal. SUPPLEMENTAL RESTRAINT SYSTEMS. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Dispose of the rear seat side airbag.

  • CAUTION:
The rear seat side airbag becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
Use gloves and safety glasses when handling a rear seat side airbag with a deployed airbag.
Do not apply water to a rear seat side airbag with a deployed airbag.
Always wash your hands with water after completing the operation.

Remove the rear seat side airbag from the tire.

Place the rear seat side airbag in a plastic bag, tie it tightly and dispose of it in the same way as other general parts.