Топливная Форсунка Установка. Corolla Auris

Using a cloth and solvent, wipe away any carbon from the sealing surface of the injector and injector installation hole, as shown in the illustration.

ПРИМЕЧАНИЕ:

1. Do not damage the sealing surface.
   
2. Do not touch the injector nozzle.
   

Install 4 new nozzle seats onto the cylinder head.

Install the injector onto the cylinder head.

ПРИМЕЧАНИЕ:

Fit the injectors into the seats.

Install the 4 nozzle holder clamp seats onto the cylinder head.

Install the 4 nozzle holder clamps onto the injectors.

Set the washer on the nozzle holder clamp, as shown in the illustration.

Temporarily tighten the 4 nozzle holder clamp bolts.

Temporarily install the 4 injection pipes onto the injector and common rail.

ПРИМЕЧАНИЕ:

Install the pipe and union nut vertically, not at a tilt.

Tighten the 4 nozzle holder clamp bolts.

Момент затяжки:

26 Н*м{265 кгс*см, 19 фунт-сила-футов}

Using SST, tighten the injection pipe union nut of the injection pipe on the common rail side.

SST

09023-38401

Момент затяжки:

With SST:

23 Н*м{235 кгс*см, 17 фунт-сила-футов}

Without SST:

25 Н*м{255 кгс*см, 18 фунт-сила-футов}

УКАЗАНИЕ:

1. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
   
2. After the injection pipe has been reassembled, check that the used pipe has no deflection and is installed properly, then replace the used pipe with a new one.
   

Using a wrench (13 mm), hold the injector steadily, and using SST, tighten the injection pipe union nut of the injection pipe on the injector side.

SST

09023-38401

Момент затяжки:

With SST:

23 Н*м{235 кгс*см, 17 фунт-сила-футов}

Without SST:

25 Н*м{255 кгс*см, 18 фунт-сила-футов}

УКАЗАНИЕ:

1. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
   
2. After the injection pipe has been reassembled, check that the used pipe has no deflection and is installed properly, then replace the used pipe with a new one.
   

Connect the 4 injector connectors.

ПРИМЕЧАНИЕ:

Connect the black connectors to injectors No. 1 and No. 3, and brown connectors to No. 2 and No. 4.

Install 5 new retainer springs onto the injectors and supply pump.

Push the new nozzle leakage pipe into each injector and supply pump.

Install the No. 2 injection pipe clamp with the nut as shown in the illustration.

Момент затяжки:

9.0 Н*м{92 кгс*см, 80 фунт-сила-дюймов}

Install the No. 1 injection pipe clamp with the 2 nuts as shown in the illustration.

Момент затяжки:

9.0 Н*м{92 кгс*см, 80 фунт-сила-дюймов}

Install the vacuum regulating valve with the 3 bolts.

Момент затяжки:

20 Н*м{204 кгс*см, 15 фунт-сила-футов}

Connect the vacuum regulating valve connector and 2 vacuum hoses.

Install the bolt and the oil level dipstick guide.

Tighten the radiator drain cock plug.

Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir filler opening.

Standard capacity:

Item	Specified Condition
without Power heater	5.4 liters (5.7 US qts, 4.8 lmp. qts)
with Power heater	5.8 liters (6.1 US qts, 5.1 lmp. qts)

УКАЗАНИЕ:

1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
   
2. Contact your TOYOTA dealer for further details.
   

ПРИМЕЧАНИЕ:

Never use water as a substitute for engine coolant.

Remove the radiator cap and air-bleeding valve and add coolant to line B of the reservoir tank.

Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.

Install the cap and valve, and warm up the engine sufficiently.

Bleed air from the cooling system.

ПРИМЕЧАНИЕ:

1. Before starting the engine, turn the A/C switch OFF.
   
2. Adjust the air conditioner set temperature to MAX (HOT).
   
3. Adjust the air conditioner set blower to Lo.
   

1. Warm up the engine until the thermostat opens. While the thermostat is open, allow the coolant to circulate for several minutes.
   

   УКАЗАНИЕ:

   The thermostat opening timing can be confirmed by squeezing the inlet radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the hose.

   ПРЕДОСТЕРЕЖЕНИЕ:

   When squeezing the radiator hose:

   1. Wear protective gloves.
      
   2. Be careful as the radiator hoses are hot.
      
   3. Keep your hands away from the radiator fan.
      

2. After the engine has warmed up, run the engine using the following cycle for at least 7 minutes: at 3000 rpm for 5 seconds, at idle speed for 45 seconds. (Repeat this cycle at least 8 times.)
   

3. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air from the system.
   

   ПРЕДОСТЕРЕЖЕНИЕ:

   When squeezing the radiator hose:

   1. Wear protective gloves.
      
   2. Be careful as the radiator hoses are hot.
      
   3. Keep your hands away from the radiator fan.
      

After the engine has cooled down, check that the coolant level is between FULL and LOW.
If the coolant level is low, add coolant to the reservoir tank F line.

Remove the radiator reservoir cap.

ПРЕДОСТЕРЕЖЕНИЕ:

To avoid the danger of being burned, do not remove the radiator reservoir cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

Fill the radiator with coolant, and then attach a radiator cap tester.

Warm up the engine.

Pump the radiator cap tester to 108 kPa (1.1 kgf/cm², 15.6 psi), and then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leakage.
If there are no signs of external coolant leaks, check the heater core, cylinder block and head.

Reinstall the radiator reservoir cap.

Connect an intelligent tester to the DLC3.

Turn the ignition switch to the ON position.

Turn the tester on.

Enter the following menu items: Powertrain / Engine and ECT / Active Test.

Perform the Active Test.

Fit the 4 retainers and install the No. 1 engine cover.