Топливный Бак Снятие. Corolla Auris

Выверните 2 болта с передней стороны левого заднего сиденья в сборе.

Снимите 2 фиксатора.

Наклоните левое заднее сиденье в сборе вперед, чтобы вывернуть 2 болта, и снимите левое заднее сиденье в сборе.

ПРИМЕЧАНИЕ:

Соблюдайте осторожность, чтобы не повредить кузов автомобиля.

Выверните 2 болта с передней стороны правого заднего сиденья в сборе.

Снимите 2 фиксатора.

Наклоните правое заднее сиденье в сборе вперед, чтобы вывернуть 2 болта на задней части, и снимите правое заднее сиденье в сборе.

ПРИМЕЧАНИЕ:

Соблюдайте осторожность, чтобы не повредить кузов автомобиля.

Turn back the floor carpet.

Remove the butyl tape, then remove the rear floor service hole cover.

Disconnect the fuel sender gauge connector.

Remove the fuel tank cap, then discharge the pressure in the fuel tank completely.

Disconnect the fuel tank main tube and return tube.

ПРИМЕЧАНИЕ:

Before beginning this procedure, check for foreign matter on the joint clips. Clean if necessary.

1. Remove the 2 tube joint clips, then pull out the fuel tube joint from the plug of the fuel tank vent tube assembly.
   

   ПРИМЕЧАНИЕ:

   1. Keep the O-ring free of foreign matter, as it becomes contaminated easily.
      
   2. Do not use any tools in this procedure.
      
   3. Do not forcefully bend, kink or twist the tube.
      
   4. Put the tube in a plastic bag to prevent damage and contamination.
      
   5. If the fuel suction plate and tube are stuck together, pinch the tube and turn it carefully to disconnect it.
      
   6. Be careful not to damage the clips. If any clip is damaged, replace it.
      

Press on tabs A from both sides of the tube.

Pull on the tube in the direction indicated by the arrow in the illustration.

Using a 6 mm socket, set SST to the fuel pump gauge retainer.

SST

09808-14020(09808-01410,09808-01420,09808-01430)

ПРИМЕЧАНИЕ:

Do not use any other tools such as a screwdriver.

УКАЗАНИЕ:

Fit the tips of SST on the ribs of the retainer.

While holding SST by hand, remove the fuel pump gauge retainer.

Remove the fuel tank vent tube assembly.

ПРИМЕЧАНИЕ:

1. Do not damage the fuel pump filter.
   
2. Be careful not to bend the fuel sender gauge arm.
   

Remove the gasket from the fuel tank assembly.

Снимите уплотнительную шайбу и фиксатор.

Выверните 3 болта, отверните гайку и снимите накладку правого защитного бруса заднего пола.

Снимите 2 уплотнительных шайбы и фиксатор.

Выверните 2 болта, отверните гайку и снимите накладку левого защитного бруса заднего пола.

Remove the 3 bolts, then remove the No. 1 fuel tank protector sub-assembly.

Remove the 4 bolts, then separate the 2 parking brake cable assemblies.

Loosen the hose clip, then disconnect the breather tube fuel hose from the fuel tank.

Loosen the hose clamp bolt, then disconnect the fuel tank filler pipe hose from the fuel tank.

Disconnect the fuel tank return tube.

1. Pinch the tabs of the retainer of the fuel tube connector to remove the lock claws and push it down as shown in the illustration.
   

2. Pull the fuel tank return tube out of the pipe.
   

   ПРИМЕЧАНИЕ:

   1. Remove any dirt or foreign objects on the fuel tube connector before starting this step.
      
   2. Avoid any scratches or foreign objects on the parts when disconnecting as the fuel tube connector has the O-ring that seals the pipe.
      
   3. Perform this work by hand. Do not use any other tools.
      
   4. Do not forcibly bend, kink or turn the nylon tube.
      
   5. Protect the connected part by covering it with a plastic bag after disconnecting the fuel tank main tube.
      
   6. If the fuel tube connector and pipe are stuck, push and pull them to release.
      

Disconnect the fuel tank main tube.

1. Pinch the tabs of the retainer of the fuel tube connector to remove the lock claws and push it down as shown in the illustration.
   

2. Pull the fuel tank main tube out of the pipe.
   

   ПРИМЕЧАНИЕ:

   1. Remove any dirt or foreign objects on the fuel tube connector before starting this step.
      
   2. Avoid any scratches or foreign objects on the parts when disconnecting as the fuel tube connector has the O-ring that seals the pipe.
      
   3. Perform this work by hand. Do not use any other tools.
      
   4. Do not forcibly bend, kink or turn the nylon tube.
      
   5. Protect the connected part by covering it with a plastic bag after disconnecting the fuel tank main tube.
      
   6. If the fuel tube connector and pipe are stuck, push and pull them to release.
      

Support the fuel tank using a transmission jack.

Remove the 4 bolts.

Lower the transmission jack to remove the fuel tank.

ПРИМЕЧАНИЕ:

1. Do not drop the fuel tank.
   
2. When removing the fuel tank, tilt it slightly to prevent it from interfering with the suspension arm or other surrounding parts.
   

Remove the 2 No. 1 fuel tank band sub-assemblies.

Remove the No. 1 fuel tank cushion and 3 No. 2 fuel tank cushions.

Remove the fuel tank return tube from the fuel tank.

Remove the fuel tank main tube from the fuel tank.