Radio Antenna Cord Removal

Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.

Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.

Using a moulding remover, disengage the claw.

Pull the upper No. 1 console panel garnish in the direction indicated by the arrow to disengage the 2 clips and remove it.

Using a moulding remover, disengage the claw.

Pull the upper No. 2 console panel garnish in the direction indicated by the arrow to disengage the 2 clips and remove it.

Disengage the 8 clips.

Disconnect the connectors and remove the console panel sub-assembly.

Open the snap.

Disengage the 7 claws and 2 clips, and then remove the rear console panel sub-assembly.

Open the snap.

Pull the front console panel sub-assembly in the direction indicated by the arrow to disengage the 6 clips and remove it.

Remove the 2 screws <F>.

Pull the front ash receptacle sub-assembly in the direction indicated by the arrow to disconnect the connectors and remove it.

Remove the rear ash receptacle assembly.

Disengage the 2 claws and 4 clips, and then remove the console box register assembly.

Remove the 2 bolts <C>.

Disconnect the 2 connectors.

Disengage the 2 clamps.

Remove the 2 bolts <C>.

Disconnect the connector.

Remove the 2 bolts <C>.

Disengage the 2 claws and 2 clips, and then remove the console box.

Using a screwdriver, disengage the 4 claws.

HINT:

Tape the screwdriver tip before use.

Apply protective tape to the areas shown in the illustration.

Using a moulding remover, disengage the 4 claws starting from the right of the No. 3 instrument panel register assembly. Disengage the remaining 3 claws by pulling the No. 3 instrument panel register assembly by hand.

NOTICE:

Do not pry the lower part of the No. 3 instrument panel register assembly. Doing so may damage the assembly.

Disconnect the connectors.

Disengage the 4 claws and remove the center lower instrument cluster finish panel.

Remove the 4 bolts.

Pull the multi-display w/ radio receiver assembly toward the rear of the vehicle.

Disconnect each connector and remove the multi-display.

Remove the 4 bolts.

Pull the integration control panel w/ radio receiver assembly toward the rear of the vehicle.

Disconnect each connector and remove the panel.

Using a screwdriver, remove the steering wheel No.3 cover lower.

HINT:

Tape up the screwdriver tip before use.

Using a screwdriver, remove the steering wheel No.2 cover lower.

HINT:

Tape up the screwdriver tip before use.

Using a "torx" socket wrench (T30), loosen the 2 "torx" screws until the groove along the screw circumference catches on the screw case.

Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand as shown in the illustration.

NOTICE:

When removing the steering pad, do not pull the airbag wire harness.

Disconnect the horn connector.

Disconnect the 2 connectors from the steering pad.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.

Remove the steering pad.

Remove the steering wheel assembly set nut.

Put matchmarks on the steering wheel assembly and main shaft assembly.

Using SST, remove the steering wheel assembly.

SST

09950-50013(09951-05010,09952-05010,09953-05020,09954-05011)

Remove the 3 screws.

Disengage the 2 claws to remove the steering column cover lower.

NOTICE:

Do not damage the tilt and telescopic switch.

Disengage the 4 clips to separate the steering column cover upper.

Disengage the claw to remove the steering column cover upper.

Remove the 2 screws.

Disengage the 2 claws to remove the lower steering column cover.

Disengage the 4 clips to separate the steering column cover upper.

Disengage the claw to remove the upper steering column cover.

Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.

Using pliers, grip the claws of the clip and remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.

Put protective tape around the front door scuff plate.

Using a moulding remover, disengage the 4 clips.

Disengage the 7 claws and remove the front door scuff plate LH.

Put protective tape around the front door scuff plate.

Using a moulding remover, disengage the 4 clips.

Disengage the 7 claws and remove the front door scuff plate LH.

Disconnect the connector.

Disengage the 6 claws and remove the front door opening trim cover LH.

Using a moulding remover, disengage the 5 claws and 3 clips, and then remove the side instrument panel LH.

Remove the 2 screws <E>.

Push the 2 claws in the direction indicated by the arrow to disengage them.

Remove the No. 1 instrument panel under cover sub-assembly from the guide as shown in the illustration and pull the cover toward the rear of the vehicle.

Disconnect the connectors and remove the No. 1 instrument panel under cover sub-assembly.

Disengage the 7 clips.

Disconnect the connectors and remove the lower instrument panel finish panel sub-assembly.

Remove the 4 bolts and driver side knee airbag assembly.

Disconnect the connector.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.

Remove the 2 screws <G> and 2 clips, and then remove the instrument cluster finish panel sub-assembly.

Using a screwdriver, disengage the 2 claws.

HINT:

Tape the screwdriver tip before use.

Disconnect the connectors and remove the combination meter assembly.

Disengage the 6 claws and remove the front door opening trim cover RH.

Using a moulding remover, disengage the 5 claws and 3 clips, and then remove the side instrument panel RH.

Using a moulding remover, disengage the 4 clips and remove the No. 2 instrument panel under cover sub-assembly.

Remove the 3 bolts and front passenger side knee airbag assembly.

Disconnect the connector.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.

Remove the 5 screws <E>.

Disengage the 2 claws.

Disconnect the connectors and remove the glove compartment door assembly.

Disengage the 2 clips from the vehicle body.

Cut off the clip <A>.

Disengage the claw and remove the front pillar garnish LH.

Remove the clip <A> from the vehicle body.

Protect the curtain shield airbag assembly.

1. Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.
   

   NOTICE:

   Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

Pull the No. 1 instrument panel register assembly in the direction indicated by the arrow to disengage the 7 claws and 2 clips, and then disconnect the connector and remove it.

Pull the No. 2 instrument panel register assembly in the direction indicated by the arrow to disengage the 4 claws and 2 clips, and then disconnect the connector and remove it.

Using a screwdriver, disengage the 7 claws and remove the No. 3 instrument panel speaker panel sub-assembly.

HINT:

Tape the screwdriver tip before use.

Remove the 2 bolts.

Lift the front stereo component speaker assembly and disconnect the connector to remove the speaker assembly.

NOTICE:

Do not touch the cone part of the speaker.

Remove the 2 clips and No. 2 console box duct.

Remove the clip and No. 1 console box duct.

Remove the clip and No. 2 console box duct.

Disengage the clamps.

Disconnect the connectors.

Disengage the 2 claws and separate the cooler thermistor.

Remove the 6 bolts <D> and nut <H>.

Remove the 2 passenger airbag bolts <A> or <B>.

Disengage the 2 clamps.

Disengage the 5 claws and remove the instrument panel safety pad assembly.

Disengage the clamp and remove the No. 2 antenna cord sub-assembly.

Detach the 2 front hooks of the seat cushion from the vehicle body.

NOTICE:

Follow the instructions below carefully as the cushion frame deforms easily.

1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.
   

2. Repeat for the other hook.
   

Detach the 2 rear hooks of the seat cushion from the seatback.

Remove the seat cushion.

Using a screwdriver, detach the claws to open the cap of the 3 rear seat shoulder belt guides.

Using a screwdriver, detach the claw to open the cap of the 3 rear seat shoulder belt guides.

Remove the 4 bolts and rear seatback assembly.

Disconnect each connector.

Remove the 3 bolts and disengage the 19 clamps.

Remove the antenna cord sub-assembly.

Remove the 3 bolts and 3 rope hook assemblies.

Using a clip remover, remove the 3 clips.

Disengage the 4 clips and remove the rear luggage compartment trim cover.

Disengage the claw and disconnect the No. 2 room light assembly.

Disconnect the connector and remove the No. 2 room light assembly.

Remove the 2 rope hooks.

Remove the 3 luggage compartment trim hooks as shown in the illustration.

Using a clip remover, remove the 2 clips.

Disengage the 4 claws and remove the front luggage compartment trim cover.

Remove the screw and luggage compartment trim hook.

Using a clip remover, remove the 3 clips and side luggage compartment trim cover.

Disconnect the connectors.

Disengage the 3 clamps and separate the antenna cord.

Disconnect each connector.

Remove the 3 bolts and disengage the 19 clamps.

Remove the antenna cord sub-assembly.