Parking Brake Pedal Removal

Detach the 2 front hooks of the seat cushion from the vehicle body.

NOTICE:

Follow the instructions below carefully as the cushion frame deforms easily.

1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.
   

2. Repeat for the other hook.
   

Detach the 2 rear hooks of the seat cushion from the seatback.

Remove the seat cushion.

Remove the bolt and disconnect the floor end of the front seat outer belt assembly.

Put protective tape around the front door scuff plate.

Using a moulding remover, disengage the 4 clips.

Disengage the 7 claws and remove the front door scuff plate LH.

Put protective tape around the front door scuff plate.

Using a moulding remover, disengage the 4 clips.

Disengage the 7 claws and remove the front door scuff plate LH.

Disconnect the connector.

Put protective tape around the rear door scuff plate.

Using a moulding remover, disengage the 2 clips.

Disengage the 5 claws and remove the the rear door scuff plate LH.

Disengage the 3 claws and 5 clips, and remove the lower center pillar garnish LH.

Disengage the 4 claws and remove the front door opening trim cover LH.

Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.

Using a moulding remover, disengage the claw.

Pull the upper No. 1 console panel garnish in the direction indicated by the arrow to disengage the 2 clips and remove it.

Using a moulding remover, disengage the claw.

Pull the upper No. 2 console panel garnish in the direction indicated by the arrow to disengage the 2 clips and remove it.

Disengage the 8 clips.

Disconnect the connectors and remove the console panel sub-assembly.

Remove the 2 screws <F>.

Pull the front ash receptacle sub-assembly in the direction indicated by the arrow to disconnect the connectors and remove it.

Remove the rear ash receptacle assembly.

Disengage the 2 claws and 4 clips, and then remove the console box register assembly.

Remove the 2 bolts <C>.

Disconnect the 2 connectors.

Disengage the 2 clamps.

Remove the 2 bolts <C>.

Disconnect the connector.

Remove the 2 bolts <C>.

Disengage the 2 claws and 2 clips, and then remove the console box.

Using a moulding remover, disengage the 5 claws and 3 clips, and then remove the side instrument panel LH.

Remove the 2 screws <E>.

Push the 2 claws in the direction indicated by the arrow to disengage them.

Remove the No. 1 instrument panel under cover sub-assembly from the guide as shown in the illustration and pull the cover toward the rear of the vehicle.

Disconnect the connectors and remove the No. 1 instrument panel under cover sub-assembly.

Disengage the 7 clips.

Disconnect the connectors and remove the lower instrument panel finish panel sub-assembly.

Remove the 4 bolts and driver side knee airbag assembly.

Disconnect the connector.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.

Remove the front floor silencer pad.

Remove the 2 clips and the No. 2 rear air duct.

Disconnect the holder (with connectors).

Remove the nut, 2 bolts and center airbag sensor assembly.

Turn back the floor carpet in order to remove the front floor rear upper sub panel.

Disengage the 6 clamps.

Remove the 4 bolts and front floor rear upper sub panel.

Disengage the claw and remove the No. 1 air duct.

Remove the parking brake return with damper spring.

Remove the 2 bolts and separate the 2 No. 2 parking brake cable assemblies from the parking brake equalizer.

Slide the rubber boot as shown in the illustration.

Remove the parking brake equalizer from the No. 1 parking brake cable assembly.

Remove the 2 bolts and 3 nuts, and separate the No. 1 parking brake cable assembly from the body.

Remove the 2 nuts and separate the instrument panel junction block assembly.

Disconnect the parking brake switch connector.

Remove the 3 nuts and parking brake pedal from the body.

Pull up the parking brake pedal claw.

Remove the lock nut and No. 1 wire adjusting nut of the No. 1 parking brake cable assembly from the parking brake pedal.

Remove the clip and No. 1 parking brake cable assembly from the parking brake pedal.

Remove the parking brake return with damper spring.

Remove the 2 bolts and separate the No. 2 parking brake cable assembles from the parking brake equalizer.

Slide the rubber boot as shown in the illustration.

Remove the parking brake equalizer from the No. 1 parking brake cable assembly.

Remove the 2 bolts and 3 nuts, and separate the No. 1 parking brake cable assembly from the body.

Remove the 2 nuts and separate the instrument panel junction block assembly.

Disconnect the parking brake switch connector.

Remove the 2 nuts, bolt and parking brake pedal from the body.

Put up the parking brake pedal claw

Remove the lock nut and No. 1 wire adjusting nut of the No. 1 parking brake cable assembly from the parking brake pedal.

Remove the clip and No. 1 parking brake cable assembly from the parking brake pedal.

Disengage the claw and remove the perking pedal pad from the parking brake pedal.