REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for 4GR-FSE)
REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for 2AD-FHV)
Brake Actuator -- Removal |
1. REMOVE COOL AIR INTAKE DUCT SEAL (for 4GR-FSE) |
Remove the 11 clips and intake duct seal.
![]() |
2. REMOVE COOL AIR INTAKE DUCT SEAL (for 2AD-FHV) |
Remove the 11 clips and intake duct seal.
![]() |
3. REMOVE ENGINE ROOM SIDE COVER LH (for 4GR-FSE) |
Remove the 5 clips and side cover.
![]() |
4. REMOVE ENGINE ROOM SIDE COVER LH (for 2AD-FHV) |
Remove the 4 clips and side cover.
![]() |
5. REMOVE ENGINE ROOM SIDE COVER RH (for 4GR-FSE) |
Remove the 2 clips and side cover.
![]() |
6. REMOVE ENGINE ROOM SIDE COVER RH (for 2AD-FHV) |
Remove the 2 clips and side cover.
![]() |
7. REMOVE FRONT UPPER FENDER PROTECTOR LH (for 4GR-FSE) |
Using a clip remover, separate the clip on the rubber portion of the cowl top ventilator louver sub-assembly from the front upper fender protector LH.
![]() |
Disengage the 3 clips and the claw to remove the front upper fender protector LH.
8. REMOVE FRONT UPPER FENDER PROTECTOR LH (for 2AD-FHV) |
Using a clip remover, separate the clip on the rubber portion of the cowl top ventilator louver sub-assembly from the front upper fender protector LH.
![]() |
Disengage the 3 clips and the claw to remove the front upper fender protector LH.
9. REMOVE FRONT UPPER FENDER PROTECTOR RH (for 4GR-FSE) |
- HINT:
- Use the same procedures for the RH side and the LH side.
10. REMOVE FRONT UPPER FENDER PROTECTOR RH (for 2AD-FHV) |
- HINT:
- Use the same procedures for the RH side and the LH side.
11. REMOVE FRONT WIPER ARM HEAD CAP (for 4GR-FSE) |
Using a screwdriver, remove the front wiper arm head cap.
- HINT:
- Use the same procedures for the RH side and the LH side.
- Tape the screwdriver tip before use.
![]() |
12. REMOVE FRONT WIPER ARM HEAD CAP (for 2AD-FHV) |
Using a screwdriver, remove the front wiper arm head cap.
- HINT:
- Use the same procedures for the RH side and the LH side.
- Tape the screwdriver tip before use.
![]() |
13. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH (for 4GR-FSE) |
Remove the nut and the front wiper arm and blade assembly LH.
![]() |
14. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH (for 2AD-FHV) |
Remove the nut and the front wiper arm and blade assembly LH.
![]() |
15. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH (for 4GR-FSE) |
Remove the nut and the front wiper arm and blade assembly RH.
![]() |
16. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH (for 2AD-FHV) |
Remove the nut and the front wiper arm and blade assembly RH.
![]() |
17. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for 4GR-FSE) |
Remove the 2 clips.
![]() |
Disengage the 11 claws, and pull out the cowl top ventilator louver sub-assembly.
![]() |
18. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for 2AD-FHV) |
Remove the 2 clips.
![]() |
Disengage the 11 claws, and pull out the cowl top ventilator louver sub-assembly.
![]() |
19. SEPARATE NO. 3 ENGINE ROOM RELAY BLOCK (for 4GR-FSE) |
Remove the bolt, nut and No. 3 engine room relay block.
- NOTICE:
- Cover the No. 3 engine room relay block with a shop rag or a piece of cloth to prevent brake fluid from getting on it.
![]() |
20. SEPARATE NO. 3 ENGINE ROOM RELAY BLOCK (for 2AD-FHV) |
Remove the bolt, nut and No. 3 engine room relay block.
- NOTICE:
- Cover the No. 3 engine room relay block with a shop rag or a piece of cloth to prevent brake fluid from getting on it.
![]() |
21. REMOVE FRONT WHEEL |
22. DRAIN BRAKE FLUID |
- NOTICE:
- If brake fluid leaks onto any painted surface, wash or remove it completely.
23. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (for 4GR-FSE) |
Disengage the clamp and disconnect the warning switch connector.
![]() |
Using SST, disconnect the 2 brake lines from the brake master cylinder sub-assembly.
- SST
- 09023-00101
Remove the 2 nuts and separate the brake actuator assembly.
Remove the 2 nuts and brake master cylinder sub-assembly from the brake booster assembly.
![]() |
Remove the O-ring from the brake master cylinder sub-assembly.
24. REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY (for 2AD-FHV) |
Disengage the clamp and disconnect the warning switch connector.
![]() |
Using SST, disconnect the 2 brake lines from the brake master cylinder sub-assembly.
- SST
- 09023-00101
Remove the 2 nuts and separate the brake actuator assembly.
Remove the 2 nuts and brake master cylinder sub-assembly from the brake booster assembly.
![]() |
Remove the O-ring from the brake master cylinder sub-assembly.
25. DISCONNECT NO. 3 FRONT BRAKE TUBE (for LHD) |
Using SST, disconnect the No. 3 front brake tube from the flexible hose.
- SST
- 09023-00101
![]() |
26. DISCONNECT NO. 2 FRONT BRAKE TUBE (for RHD) |
Using SST, disconnect the No. 2 front brake tube from the flexible hose.
- SST
- 09023-00101
![]() |
27. REMOVE BRAKE ACTUATOR ASSEMBLY WITH BRACKET |
Release the lock lever and disconnect the actuator connector.
![]() |
Using SST, disconnect the 6 brake tubes from the brake actuator assembly with bracket.
- SST
- 09023-00101
Use tags or make a memo to identify the places to reconnect.
- HINT:
- *1: To Front Wheel Cylinder RH
- *2: To Front Wheel Cylinder LH
- *3: To Rear Wheel Cylinder RH
- *4: To Rear Wheel Cylinder LH
- *5: From Front Master Cylinder
- *6: From Rear Master Cylinder
Separate the grommet and remove the No. 3 front brake tube.
- NOTICE:
- Do not damage the brake tube.
Remove the 2 bolts, nut and brake actuator assembly with bracket from the body.
- NOTICE:
- Do not damage the brake tubes.
28. REMOVE BRAKE ACTUATOR BRACKET ASSEMBLY |
Remove the 2 nuts and the brake actuator from the actuator bracket assembly.
![]() |
Remove the brake actuator bolt cushion and actuator bracket.
29. REMOVE BRAKE ACTUATOR BOLT CUSHION |
Remove the 2 bolts and the 2 brake actuator bolt cushions from the brake actuator assembly.
![]() |