Brake Actuator -- Removal |
1. REMOVE COOL AIR INTAKE DUCT SEAL |
Remove the 11 clips and intake duct seal.
![]() |
2. REMOVE ENGINE ROOM SIDE COVER LH |
Remove the 5 clips and side cover.
![]() |
3. REMOVE ENGINE ROOM SIDE COVER RH |
Remove the 2 clips and side cover.
![]() |
4. REMOVE FRONT UPPER FENDER PROTECTOR LH |
Using a clip remover, separate the clip on the rubber portion of the cowl top ventilator louver sub-assembly from the front upper fender protector LH.
![]() |
Disengage the 3 clips and the claw to remove the front fender protector upper LH.
5. REMOVE FRONT UPPER FENDER PROTECTOR RH |
- HINT:
- Use the same procedures for the RH side and the LH side.
6. REMOVE FRONT WIPER ARM HEAD CAP |
Using a screwdriver, remove the front wiper arm head cap.
- HINT:
- Use the same procedures for the RH side and the LH side.
- Tape the screwdriver tip before use.
![]() |
7. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH |
Remove the nut and the front wiper arm and blade assembly LH.
![]() |
8. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH |
Remove the nut and the front wiper arm and blade assembly RH.
![]() |
9. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
Remove the 2 clips.
![]() |
Disengage the 11 claws, and pull out the cowl top ventilator louver sub-assembly.
![]() |
10. SEPARATE NO. 3 ENGINE ROOM RELAY BLOCK |
Remove the bolt, nut and No. 3 engine room relay block.
- NOTICE:
- Cover the No. 3 engine room relay block with a shop rag or a piece of cloth to prevent brake fluid from getting on it.
![]() |
11. REMOVE FRONT WHEEL |
12. DRAIN BRAKE FLUID |
- NOTICE:
- If brake fluid leaks onto any painted surface, wash or remove it completely.
13. REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY |
Disengage the clamp and disconnect the warning switch connector.
![]() |
Using SST, disconnect the 2 brake lines from the brake master cylinder sub-assembly.
- SST
- 09023-00101
Remove the 2 nuts and separate the brake actuator assembly.
Remove the 2 nuts and brake master cylinder sub-assembly from the brake booster assembly.
![]() |
Remove the O-ring from the brake master cylinder sub-assembly.
14. DISCONNECT NO. 3 FRONT BRAKE TUBE (for LHD) |
Using SST, disconnect the No. 3 front brake tube from the flexible hose.
- SST
- 09023-00101
![]() |
15. DISCONNECT NO. 2 FRONT BRAKE TUBE (for RHD) |
Using SST, disconnect the No. 2 front brake tube from the flexible hose.
- SST
- 09023-00101
![]() |
16. REMOVE BRAKE ACTUATOR ASSEMBLY WITH BRACKET |
Release the lock lever and disconnect the actuator connector.
![]() |
Using SST, disconnect the 6 brake tubes from the brake actuator assembly with bracket.
- SST
- 09023-00101
Use tags or make a memo to identify the places to reconnect.
- HINT:
- *1: To Front Wheel Cylinder RH
- *2: To Front Wheel Cylinder LH
- *3: To Rear Wheel Cylinder RH
- *4: To Rear Wheel Cylinder LH
- *5: From Front Master Cylinder
- *6: From Rear Master Cylinder
Separate the grommet and remove the No. 3 front brake tube.
- NOTICE:
- Do not damage the brake tube.
Remove the 2 bolts, nut and brake actuator assembly with bracket from the body.
- NOTICE:
- Do not damage the brake tubes.
17. REMOVE BRAKE ACTUATOR BRACKET ASSEMBLY |
Remove the 2 nuts and the brake actuator from the actuator bracket assembly.
![]() |
Remove the brake actuator bolt cushion and actuator bracket.
18. REMOVE BRAKE ACTUATOR BOLT CUSHION |
Remove the 2 bolts and the 2 brake actuator bolt cushions from the brake actuator assembly.
![]() |