Dtc C1235/35 Foreign Object Is Attached On Tip Of Front Speed Sensor Rh

Brake. Lexus Is250, Is220D. Gse20 Ale20
Brake Control. Lexus Is250, Is220D. Gse20 Ale20

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - EACH SPEED SENSOR)

INSPECT SKID CONTROL ECU (SENSOR INPUT)

RECONFIRM DTC

CHECK REAR SPEED SENSOR TIP

CHECK EACH SPEED SENSOR ROTOR

RECONFIRM DTC

REPLACE EACH SPEED SENSOR

RECONFIRM DTC

DTC C1235/35 Foreign Object is Attached on Tip of Front Speed Sensor RH

DTC C1236/36 Foreign Object is Attached on Tip of Front Speed Sensor LH

DTC C1238/38 Foreign Object is Attached on Tip of Rear Speed Sensor RH

DTC C1239/39 Foreign Object is Attached on Tip of Rear Speed Sensor LH

DTC C1275/75 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)

DTC C1276/76 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)

DTC C1277/77 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)

DTC C1278/78 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU. These signals are used for the ABS control system. This speed sensor contains a sensor IC, which consists of 2 MREs (Magnetic Resistance Element). The speed sensor rotor, which consists of 48 sets of N and S poles that are arranged in a circle, is integrated with the inner race of the hub bearing.
To detect the rotation direction, the output waves are used to determine the relationship of the pulses that are generated by 2 MREs. Upon receiving this signal, the sensor IC outputs a forward or backward wave to the ECU.
DTCs C1275/75 to C1278/78 can be deleted when the speed sensor sends a vehicle speed signal or the Test Mode ends. DTCs C1275/75 to C1278/78 are output only in the Test Mode.
Lexus Is250, Is220D. Gse20 Ale20.Brake Control.Vehicle Stability Control System (W/ Vdim).
Dtc
  C1235/35  Foreign Object Is Attached On Tip Of Front Speed Sensor Rh

DTC No.
DTC Detection Condition
Trouble Area
C1235/35
C1236/36
C1238/38
C1239/39
When either of the following is detected:
  1. At a vehicle speed of 12 mph (20 km/h) or more, noise occurs in the sensor signal from the abnormal wheel for 5 seconds or more.
  2. At a vehicle speed of 6 mph (10 km/h) or more, noise is input once per rotor rotation for 15 seconds or more.
  1. Speed sensor
  2. Speed sensor rotor
  3. Sensor installation
  4. Brake actuator assembly
    (Skid control ECU)
HINT:
  1. DTC C1235/35 is for the front speed sensor RH.
  2. DTC C1236/36 is for the front speed sensor LH.
  3. DTC C1238/38 is for the rear speed sensor RH.
  4. DTC C1239/39 is for the rear speed sensor LH.

WIRING DIAGRAM


Lexus Is250, Is220D. Gse20 Ale20.Brake Control.Vehicle Stability Control System (W/ Vdim).
Dtc
  C1235/35  Foreign Object Is Attached On Tip Of Front Speed Sensor Rh


Lexus Is250, Is220D. Gse20 Ale20.Brake Control.Vehicle Stability Control System (W/ Vdim).
Dtc
  C1235/35  Foreign Object Is Attached On Tip Of Front Speed Sensor Rh


INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).
HINT:
When C0200/31, C0205/32, C0210/33, or C0215/34 is output together with C1235/35, C1236/36, C1238/38, or C1239/39, inspect and repair the trouble areas indicated by C0200/31, C0205/32, C0210/33, or C0215/34 first.
1.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - EACH SPEED SENSOR)


    Lexus Is250, Is220D. Gse20 Ale20.Brake Control.Vehicle Stability Control System (W/ Vdim).
Dtc
  C1235/35  Foreign Object Is Attached On Tip Of Front Speed Sensor Rh
  1. Disconnect the skid control ECU connector and each speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    RH:
    Tester Connection
    Condition
    Specified Condition
    A14-3 (FR+) - V1-2 (FR+)
    Always
    Below 1 Ω
    A14-3 (FR+) - Body ground
    Always
    10 kΩ or higher
    A14-17 (FR-) - V1-1 (FR-)
    Always
    Below 1 Ω
    A14-17 (FR-) - Body ground
    Always
    10 kΩ or higher
    A14-5 (RR+) - X1-2 (RR+)
    Always
    Below 1 Ω
    A14-5 (RR+) - Body ground
    Always
    10 kΩ or higher
    A14-19 (RR-) - X1-1 (RR-)
    Always
    Below 1 Ω
    A14-19 (RR-) - Body ground
    Always
    10 kΩ or higher
    LH:
    Tester Connection
    Condition
    Specified Condition
    A14-18 (FL+) - W1-2 (FL+)
    Always
    Below 1 Ω
    A14-18 (FL+) - Body ground
    Always
    10 kΩ or higher
    A14-4 (FL-) - W1-1 (FL-)
    Always
    Below 1 Ω
    A14-4 (FL-) - Body ground
    Always
    10 kΩ or higher
    A14-20 (RL+) - Y1-2 (RL+)
    Always
    Below 1 Ω
    A14-20 (RL+) - Body ground
    Always
    10 kΩ or higher
    A14-6 (RL-) - Y1-1 (RL-)
    Always
    Below 1 Ω
    A14-6 (RL-) - Body ground
    Always
    10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT SKID CONTROL ECU (SENSOR INPUT)


    Lexus Is250, Is220D. Gse20 Ale20.Brake Control.Vehicle Stability Control System (W/ Vdim).
Dtc
  C1235/35  Foreign Object Is Attached On Tip Of Front Speed Sensor Rh
  1. Reconnect the skid control ECU connector.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    RH:
    Tester Connection
    Condition
    Specified Condition
    V1-2 (FR+) - Body ground
    Engine switch on (IG)
    7.5 to 14 V
    X1-2 (RR+) - Body ground
    Engine switch on (IG)
    7.5 to 14 V
    LH:
    Tester Connection
    Condition
    Specified Condition
    W1-2 (FL+) - Body ground
    Engine switch on (IG)
    7.5 to 14 V
    Y1-2 (RL+) - Body ground
    Engine switch on (IG)
    7.5 to 14 V


NG
REPLACE BRAKE ACTUATOR ASSEMBLY
OK


3.RECONFIRM DTC
  1. Turn the engine switch off.

  1. Reconnect the speed sensor connector.

  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at the speed of 12 mph (20 km/h) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Condition
    Proceed to
    DTCs (C1235/35, C1236/36, C1238/38 and/or C1239/39) are output (for rear)
    A
    DTCs (C1235/35, C1236/36, C1238/38 and/or C1239/39) are output (for front)
    B
    DTCs (C1235/35, C1236/36, C1238/38 and/or C1239/39) are not output
    C


B
Go to step 5

C
USE SIMULATION METHOD TO CHECK
A


4.CHECK REAR SPEED SENSOR TIP
  1. Turn the engine switch off.

  1. Remove the rear speed sensor (Click here).

  1. Check the speed sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.
    NOTICE:
    Check the speed sensor signal after cleaning/replacement (Click here).


NG
CLEAN OR REPLACE REAR SPEED SENSOR
OK


5.CHECK EACH SPEED SENSOR ROTOR
  1. Turn the engine switch off.

  1. Remove each speed sensor rotor.

  1. Check the speed sensor rotor.

    OK:
    No scratches, oil, or foreign matter on the rotors.
    NOTICE:
    Check the speed sensor signal after cleaning/replacement (Click here).


NG
CLEAN OR REPLACE EACH SPEED SENSOR ROTOR
OK


6.RECONFIRM DTC
  1. Install the speed sensor and the speed sensor rotor.

  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at the speed of 12 mph (20 km/h) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Condition
    Proceed to
    DTCs (C1235/35, C1236/36, C1238/38 and/or C1239/39) are output
    A
    DTCs (C1235/35, C1236/36, C1238/38 and/or C1239/39) are not output
    B


B
USE SIMULATION METHOD TO CHECK
A


7.REPLACE EACH SPEED SENSOR
  1. Turn the engine switch off.

  1. Replace each speed sensor (Click here for front, or Click here for rear).

    NOTICE:
    Check the speed sensor signal after replacement (Click here).

NEXT


8.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at the speed of 12 mph (20 km/h) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Condition
    Proceed to
    DTCs (C1235/35, C1236/36, C1238/38 and/or C1239/39) are output
    A
    DTCs (C1235/35, C1236/36, C1238/38 and/or C1239/39) are not output
    B


B
END
A

REPLACE BRAKE ACTUATOR ASSEMBLY