Dtc B1835/58 Short In Curtain Shield Squib Lh Circuit

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (CURTAIN SHIELD SQUIB LH)

CHECK CONNECTOR

CHECK FLOOR WIRE NO.2 (CURTAIN SHIELD SQUIB LH CIRCUIT)

CHECK CENTER AIRBAG SENSOR ASSEMBLY

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

HINT:

1. Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester (Click here).
   
2. After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).
   

1. Turn the engine switch off.
   

2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
   

3. Disconnect the connector from the curtain shield airbag assembly LH.
   

4. Connect the white wire side of SST (resistance 2.1 Ω) to connector "C".
   

   CAUTION:

   Never connect a tester to the curtain shield airbag assembly LH (Curtain shield squib LH) for measurement, as the may lead to a serious injury due to airbag deployment.

   NOTICE:

   1. Do not forcibly insert the SST into the terminals of the connector when connecting.
      
   2. Insert straight the SST into the terminals of the connector.
      

SST

09843-18060

5. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
   

6. Turn the engine switch on (IG), and wait for at least 60 seconds.
   

7. Clear the DTCs stored in memory (Click here).
   

8. Turn the engine switch off.
   

9. Turn the engine switch on (IG), and wait for at least 60 seconds.
   

10. Check the DTCs (Click here ).
    

    OK:

    DTC B1835, B1836, B1837, B1838 or 58 is not output.
    

    HINT:

    Codes other than DTC B1835, B1836, B1837, B1838 and 58 may be output at this time, but they are not related to this check.

1. Turn the engine switch off.
   

2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
   

3. Disconnect the SST from connector "C".
   

4. Check that the floor wire No.2 connector (on the curtain shield assembly LH side) is not damaged.
   

   OK:

   The lock button is not disengaged, or the claw of the lock is not deformed or damaged.
   

1. Disconnect the connectors from the center airbag sensor assembly.
   

2. Check the short to B+ in the circuit.
   

   1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
      

   2. Turn the engine switch on (IG).
      

   3. Measure the voltage according to the value(s) in the table below.
      

      Voltage:

      Tester connection	Condition	Specified condition
      W19-1 (ICL+) - Body ground	Engine switch on (IG)	Below 1 V
      W19-2 (ICL-) - Body ground	Engine switch on (IG)	Below 1 V

3. Check the open in the circuit.
   

   1. Turn the engine switch off.
      

   2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
      

   3. Measure the resistance according to the value(s) in the table below.
      

      Resistance:

      Tester connection	Condition	Specified condition
      W19-1 (ICL+) - W19-2 (ICL-)	Always	Below 1 Ω

4. Check the short to ground in the circuit.
   

   1. Measure the resistance according to the value(s) in the table below.
      

      Resistance:

      Tester connection	Condition	Specified condition
      W19-1 (ICL+) - Body ground	Always	1 MΩ or higher
      W19-2 (ICL-) Body ground	Always	1 MΩ or higher

5. Check the short in the circuit.
   

   1. Release the activation prevention mechanism built into connector "B" (Click here).
      

   2. Measure the resistance according to the value(s) in the table below.
      

      Resistance:

      Tester connection	Condition	Specified condition
      W19-1 (ICL+) - W19-2 (ICL-)	Always	1 MΩ or higher

1. Connect the connectors to the curtain shield airbag assembly LH and the center airbag sensor assembly.
   

2. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
   

3. Turn the engine switch on (IG), and wait for at least 60 seconds.
   

4. Clear the DTCs stored in memory (Click here).
   

5. Turn the engine switch off.
   

6. Turn the engine switch on (IG), and wait for at least 60 seconds.
   

7. Check the DTCs (Click here).
   

   OK:

   DTC B1835, B1836, B1837, B1838 or 58 is not output.
   

   HINT:

   Codes other than DTC B1835, B1836, B1837, B1838 and 58 may be output at this time, but they are not related to this check.