Water Pump Installation

Install a new O-ring to the water by-pass hose.

Install a new gasket and the water pump with the 5 bolts, 2 stud bolts and nut.

Torque:

21 N*m{214 kgf*cm, 15 ft.*lbf} for bolts

18 N*m{194 kgf*cm, 24 ft.*lbf} for nuts and stud bolts

Install the pulley with the bolt.

Torque:

34.5 N*m{352 kgf*cm, 25 ft.*lbf}

Install a new O-ring.

Apply soapy water to the O-ring.

Apply seal packing to the groove of the water inlet housing as shown in the illustration.

Seal packing:

Part No. 08826-00100 or equivalent

NOTICE:

1. After applying seal packing, install the part within 5 minutes.
   
2. Be sure to keep the O-ring away from engine oil. The O-ring must be replaced if it contacts engine oil.
   

Install the water inlet housing with the 2 bolts. Then connect the water hose.

Bolt length:

Item	Specified Condition
Bolt A	77 mm (3.03 in.)
Bolt B	22 mm (0.86 in.)

Torque:

18 N*m{194 kgf*cm, 24 ft.*lbf}

Check the No. 1 and No. 2 belt idlers.

1. Visually check the seal portion of the idler pulley for oil leakage.
   

   1. If leakage is found, replace the idler.
      

2. Check that the idler turns smoothly.
   

   1. If necessary, replace the idler.
      

Check the water pump.

1. Visually check the air hole and water hole for coolant leakage.
   

   1. If leakage is found, replace the water pump and belt.
      

2. Turn the pulley, and check that the water pump bearing moves smoothly and quietly.
   

   1. If necessary, replace the water pump.
      

Remove any oil or water on the crankshaft, oil pump pulley, water pump pulley, No. 1 and No. 2 idler. Keep them clean.

NOTICE:

Only wipe the pulleys. Do not use any cleansing agents on the pulleys.

Set the No. 1 cylinder to TDC/compression.

1. Turn the hexagon head portion of the camshaft to align the timing marks of the camshaft timing pulleys and timing belt plates.
   
   

   HINT:

   Turn the camshaft timing pulleys slightly clockwise to make installation of the timing belt easier.

   Camshaft timing pulley of LH bank:

   1/2 of a tooth
   

   Camshaft timing pulley of RH bank:

   1 tooth
   





2. Using the crankshaft damper bolt, turn the crankshaft to align the timing marks of the crankshaft timing pulley and oil pump body.
   





3. Remove any oil or water on each pulley. Keep them clean.
   

   NOTICE:

   Only wipe the pulleys. Do not use cleaning agents on the pulleys.

4. Face the front mark (arrow) on the belt forward.
   

5. Connect the belt to the crankshaft timing pulley. Align the installation mark on the belt with the timing mark of the crankshaft timing pulley.
   

6. Connect the belt to the No. 2 idler.
   

7. Connect the belt to the camshaft timing pulley (LH bank). Align the installation mark on the belt with the timing mark of the camshaft timing pulley.
   

8. Connect the belt to the water pump pulley.
   

9. Connect the belt to the camshaft timing pulley (RH bank). Align the installation mark on the belt with the timing mark of the camshaft timing pulley.
   

10. Connect the timing belt to the No. 1 idler.
    

Set the belt tensioner.

1. Using a press, slowly press in the push rod using 981 to 9,807 N (100 to 1,000 kgf, 220 to 2,205 lbf) of pressure.
   

2. Align the holes of the push rod and housing. Pass a 1.27 mm hexagon wrench through the holes to keep the setting position of the push rod.
   

3. Release the press.
   

4. Install the dust boot to the belt tensioner.
   

Install the belt tensioner.

1. Temporarily install the belt tensioner with the 2 bolts.
   

2. Alternately tighten the 2 bolts.
   

   Torque:

   26 N*m{265 kgf*cm, 19 ft.*lbf}

3. Using pliers, remove the 1.27 mm hexagon wrench from the belt tensioner.
   

Check the valve timing.

1. Using the crankshaft damper bolt, slowly turn the crankshaft timing pulley 2 revolutions from TDC to TDC.
   

   NOTICE:

   Always turn the crankshaft pulley clockwise.





2. Check that each pulley aligns with the timing marks as shown in the illustration.
   

   1. If the pulley and timing marks do not align, remove the belt and reinstall it.
      

3. Remove the crankshaft damper bolt.
   

Install the sensor with the bolt and stud bolt.

Torque:

7.5 N*m{76 kgf*cm, 66 in.*lbf}

Install a new gasket and cover spacer.

Install the timing belt cover with the 4 bolts.

Torque:

7.5 N*m{76 kgf*cm, 66 in.*lbf}

Set the No. 2 cover by matching the claws and pin with each part.

Install the timing belt cover with the 2 bolts.

Torque:

16 N*m{163 kgf*cm, 12 ft.*lbf}

HINT:

Use bolts that are 106 mm (4.17 in.) in length.

Install the idler with the 2 bolts and 2 nuts.

Torque:

16 N*m{163 kgf*cm, 12 ft.*lbf} for 12 mm head

Torque:

32 N*m{326 kgf*cm, 24 ft.*lbf} for 14 mm head

Bolt length:

106 mm (4.17 in.) for 12 mm head bolt A

114 mm (4.49 in.) for 14 mm head bolt B

Install the gasket to the cover.

Install the cover with the cap nut and 3 bolts.

Torque:

7.5 N*m{76 kgf*cm, 66 in.*lbf}

Install the gasket to the cover.

Pass the camshaft position sensor wire through the cover hole.

Install the cover with the 4 bolts.

Torque:

7.5 N*m{76 kgf*cm, 66 in.*lbf}

Install the wire grommet to the cover.

Install the sensor connector to the sensor holder.

Connect the sensor connector.

Install the sensor wire to the wire clamp on the cover.

Install the engine wire to the 2 wire clamps on the cover.

Connect the 3 water by-pass hoses as shown in the illustration.

Install the oil cooler pipe to the cover with the cap nut and the bolt.

Torque:

7.5 N*m{76 kgf*cm, 66 in.*lbf}

Align the damper set key with the key groove of the crankshaft damper.

Using SST and a hammer, tap in the crankshaft damper.

SST

09223-46011

Using SST, install the damper bolt.

SST

09213-70011
09330-00021

Torque:

245 N*m{2,498 kgf*cm, 181 ft.*lbf}

Install the pulley with the bolt.

Torque:

39 N*m{398 kgf*cm, 29 ft.*lbf}

Install the belt tensioner with the bolt and 2 nuts.

Torque:

15.5 N*m{158 kgf*cm, 11 ft.*lbf}

HINT:

Use a bolt that is 106 mm (4.17 in.) in length.

Hang the compressor bracket onto the fan bracket and temporarily install the compressor with the bolt.

Install the compressor with the 3 bolts, nut and bracket.

Torque:

49 N*m{500 kgf*cm, 36 ft.*lbf} for bolt

29.4 N*m{300 kgf*cm, 22 ft.*lbf} for nut

NOTICE:

Tighten the bolts in the order shown in the illustration to install the compressor.

Install the generator with the bolt and 2 nuts.

HINT:

Install the bolt and 2 nuts in alphabetical order.

Torque:

39 N*m{398 kgf*cm, 29 ft.*lbf} for bolt A and nut B

15.5 N*m{158 kgf*cm, 11 ft.*lbf} for nut C

Install the ground cable with the bolt D.

Install the battery cable with the nut, and then attach the rubber cap.

Torque:

12 N*m{122 kgf*cm, 9 ft.*lbf}

Install the bracket with the bolt.

Torque:

6.0 N*m{61 kgf*cm, 53 in.*lbf}

Connect the cable to the generator.

Set the V-belt to everything except the No. 2 idler pulley, as shown in the illustration.

Loosen the V-belt by turning the belt tensioner counterclockwise.

Then set the V-belt to the idler pulley.

After a new belt has been installed, check that the mark is within the A range shown in the illustration.

Install the 2 radiator support cushions and 2 radiator lower supports to the radiator.

Install the fan to the radiator, and attach the 3 claws.

Install the radiator and attach the ECM outlet duct.

Align the radiator with the condenser. Then install the radiator with the 4 bolts.

Torque:

5.0 N*m{51 kgf*cm, 44 in.*lbf}

Install the radiator support with the 5 bolts.

Torque:

5.5 N*m{56 kgf*cm, 48 in.*lbf}

Attach the 6 clamps and install the wire harness.

Apply MP grease to the sliding areas of the lock.

Install the hood lock.

Install the 2 bolts and nut.

Torque:

8.0 N*m{82 kgf*cm, 71 in.*lbf}

Install a new cap.

Connect the hood lock control cable.

Attach the claw and install the cable cover.

Install the 3 screws.

Install the cover with the 4 clips.

Connect the ultrasonic sensor connector.

Attach the 3 claws on the LH side.

Attach the 3 claws on the RH side.

Install the bumper cover with the 2 clips, 6 screws and 5 bolts.

Temporarily install the oil cooler outlet tube.

Temporarily install the oil cooler inlet tube.

Install the 2 clamps with the 2 bolts.

Torque:

5.0 N*m{51 kgf*cm, 44 in.*lbf}

Tighten the oil cooler outlet tube No. 1.

Torque:

42 N*m{428 kgf*cm, 31 ft.*lbf}

NOTICE:

Use a torque wrench with a fulcrum length of 460 mm (18.11 in.).

Tighten the oil cooler inlet tube.

Torque:

42 N*m{428 kgf*cm, 31 ft.*lbf}

NOTICE:

Use a torque wrench with a fulcrum length of 460 mm (18.11 in.).

Connect the hose outlet.

HINT:

1. Face the clamp's claw toward the bottom of the vehicle.
   

1. Make sure the clearance between the clamp edge and radiator hose edge (labeled A) is between 1 to 5 mm (0.039 to 0.197 in.).
   

1. Insert the hose until it contacts the radiator. Make sure the clearance between the hose and radiator (labeled B) is between 0 to 2.5 mm (0 to 0.098 in.).
   

Connect the hose inlet.

Tighten the radiator drain cock plug by hand.

Tighten the 2 cylinder block drain cock plugs.

Torque:

12.7 N*m{130 kgf*cm, 9 ft.*lbf}

Add engine coolant.

HINT:

Add engine coolant until coolant overflows from the vent plug.

Specified capacity:

11.0 liters (11.7 US qts, 9.7 lmp. qts)

HINT:

1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
   

1. Please contact your TOYOTA dealer for further details.
   

Install the vent plug.

Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.

Install the radiator cap.

Bleed air from the cooling system.

1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
   

   HINT:

   Adjust the air conditioner set temperature to MAX (HOT).

2. Maintain the engine speed at 2,000 to 2,500 rpm.
   

3. Press the inlet and outlet radiator hoses several times by hand to bleed air.
   

   NOTICE:

   When pressing the radiator hoses:

   1. Wear protective gloves.
      
   1. Be careful as the radiator hoses are hot.
      
   1. Keep your hands away from the radiator fan.
      

Stop the engine, and wait until the engine coolant cools down to ambient temperature.

CAUTION:

Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

Check the coolant level in the radiator reservoir.
If the coolant level is low, add SLLC to the radiator reservoir FULL line.

Check for engine coolant leaks (Click here).

Install the air cleaner assembly with the 3 bolts.

Torque:

5.0 N*m{51 kgf*cm, 44 in.*lbf}

Connect the MAF meter connector and clamp to the air cleaner.

Install the inlet with the bolt.

Torque:

5.0 N*m{51 kgf*cm, 44 in.*lbf}

Install the side cover with the 3 clips.

Install the side cover with the 2 clips and nut.

Install the duct seal with the 7 clips.

Install the cover with the 2 nuts.

Torque:

5.0 N*m{51 kgf*cm, 44 in.*lbf}

Connect the ultrasonic sensor connector.

Attach the 3 claws on the LH side.

Attach the 3 claws on the RH side.

Install the bumper cover with the 2 clips, 6 screws and 5 bolts.

Perform initialization (Click here).

NOTICE:

Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.