Dtc P0011 Camshaft Position A - Timing Over-Advanced Or System Performance (Bank 1)

Engine. Lexus Gs430, Gs300. Uzs190 Grs190
3Gr-Fe Engine Control System. Lexus Gs430, Gs300. Uzs190 Grs190

DESCRIPTION

MONITOR DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022)

PERFORM ACTIVE TEST BY CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OPERATE OCV)

CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)

CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)

INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OCV)

INSPECT OIL CONTROL VALVE FILTER

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

READ VALUE OF INTELLIGENT TESTER (CHECK IF DTC OUTPUT RECURS)

DTC P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)

DTC P0012 Camshaft Position "A" - Timing Over-Retarded (Bank 1)

DTC P0021 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2)

DTC P0022 Camshaft Position "A" - Timing Over-Retarded (Bank 2)


DESCRIPTION

The Variable Valve Timing (VVT) system includes the ECM, Oil Control Valve (OCV) and VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as intake air volume, throttle valve position and engine coolant temperature. The ECM controls the OCV, based on the signals transmitted by several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the OCV. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improves, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target intake valve timing is verified by the ECM.

DTC No.
DTC Detection Condition
Trouble Area
P0011
P0021
Advanced cam timing:
With warm engine and engine speed of between 500 rpm and 4,000 rpm, all conditions (1), (2) and (3) met (1 trip detection logic):
1. Difference between target and actual intake valve timing more than 5°CA (Crankshaft Angle) for 4.5 seconds
2. Current intake valve timing fixed (timing changes less than 5°CA in 5 seconds)
3. Variations in VVT controller timing more than 19°CA of maximum delayed timing (advance)
  1. Valve timing
  2. Oil Control valve (OCV) for intake camshaft (bank 1)
  3. OCV filter (bank 1)
  4. Intake camshaft (bank 1) timing gear assembly
  5. ECM
P0012
P0022
Retarded cam timing:
With warm engine and engine speed of between 500 rpm and 4,000 rpm, all conditions (1), (2) and (3) met (2 trip detection logic):
1. Difference between target and actual intake valve timing more than 5°CA (Crankshaft Angle) for 4.5 seconds
2. Current intake valve timing fixed (timing changes less than 5°CA in 5 seconds)
3. Variations in VVT controller timing 19°CA or less of maximum delayed timing (retarded)
  1. Valve timing
  2. OCV for intake camshaft (bank 2)
  3. OCV filter (bank 2)
  4. Intake camshaft (bank 2) timing gear assembly
  5. ECM

MONITOR DESCRIPTION

  1. The ECM optimizes the intake valve timing using the VVT (Variable Valve Timing) system to control the intake camshaft. The VVT system includes the ECM, the Oil Control Valve (OCV) and the VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.
  2. If the difference between the target and actual intake valve timing is large, and changes in actual intake valve timing are small, the ECM interprets this as the VVT controller stuck malfunction and set a DTC.
  1. Example:
  2. A DTC is set when the following conditions 1, 2 and 3 are met:
    1. 1. The difference between the target and actual intake valve timing is more than 5°CA (Crankshaft Angle) and the condition continues for more than 4.5 seconds.
    2. 2. It takes 5 seconds or more to change the valve timing by 5°CA.
    3. 3. After above conditions 1 and 2 are met, the OCV is forcibly activated 63 times or more.
  3. DTCs P0011 and P0021 (Advanced Cam Timing) are subject to 1 trip detection logic.
  4. DTCs P0012 and P0022 (Retarded Cam Timing) are subject to 2 trip detection logic.
  5. These DTCs indicate that the VVT controller cannot operate properly due to OCV malfunctions or the presence of foreign objects in the OCV.
  6. The monitor will not run unless the following conditions are met:
    1. The engine is warm (the engine coolant temperature is 75°C (167°F) or more).
    2. The vehicle has been driven at more than 64 km/h (40 mph) for 3 minutes.
    3. The engine has idled for 3 minutes.

WIRING DIAGRAM

Refer to DTC P0010 on page Click here.

INSPECTION PROCEDURE


HINT:

Abnormal bank
Advanced timing over
(Valve timing is out of specified range)
Retarded timing over
(Valve timing is out of specified range)
Bank 1
P0011
P0012
Bank 2
P0021
P0022
  1. If DTC P0011 or P0012 is displayed, check the right bank VVT system for intake camshaft circuit (bank 1).
  1. Bank 1 refers to the bank that include cylinder No. 1.
  1. If DTC P0021 or P0022 is displayed, check the left bank VVT system for intake camshaft circuit (bank 2).
  1. Bank 2 refers to the bank that does not include cylinder No. 1.
  1. Read freeze frame data using an intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read DTCs.

    Result:

    Display (DTC Output)
    		Proceed to
    P0011, P0012, P0021 or P0022
    		A
    P0011, P0012, P0021 or P0022 and other DTCs
    		B
HINT:
If any DTCs other than P0011, P0012, P0021 or P0022 are output, troubleshoot those DTCs first.


B
GO TO DTC CHART
A


2.PERFORM ACTIVE TEST BY CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OPERATE OCV)

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester ON.

  1. Warm up the engine.

  1. On the tester, enter the following menus: Powertrain / Engine / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2).

  1. Check the engine speed while operating the Oil Control Valve (OCV) using the tester.

    OK:

    Tester Operation
    		Specified Condition
    OCV OFF
    		Normal engine speed
    OCV ON
    		Engine idles roughly or stalls (soon after OCV switched from OFF to ON)


NG
Go to step 4
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester ON.

  1. Clear DTCs (Click here).

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the tester (Click here).

  1. Drive the vehicle for more than 10 minutes.

  1. Read DTCs using the tester.

    OK:
    No DTC output.


NG
Go to step 4
OK

END

4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)


    Lexus Gs430, Gs300. Uzs190 Grs190.3Gr-Fe Engine Control System.Sfi System. Dtc P0011 Camshaft Position A - Timing Over-Advanced Or System Performance (Bank 1)

  1. Remove the cylinder head cover RH and LH.

  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.

    1. If not, turn the crankshaft 1 revolution (360°), then align the marks as above.
    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

  1. Reinstall the cylinder head cover.



NG
ADJUST VALVE TIMING
OK


5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OCV)
Lexus Gs430, Gs300. Uzs190 Grs190.3Gr-Fe Engine Control System.Sfi System. Dtc P0011 Camshaft Position A - Timing Over-Advanced Or System Performance (Bank 1)

  1. Remove the OCV.

  1. Measure the resistance between the terminals of the OCV.

    Standard resistance:
    6.9 to 7.9 Ω at 20°C (68°F)

  1. Apply positive battery voltage to terminal 1 and negative battery voltage to terminal 2. Check the valve operation.

    OK:
    Valve moves quickly.

  1. Reinstall the OCV.



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
OK


6.INSPECT OIL CONTROL VALVE FILTER
Lexus Gs430, Gs300. Uzs190 Grs190.3Gr-Fe Engine Control System.Sfi System. Dtc P0011 Camshaft Position A - Timing Over-Advanced Or System Performance (Bank 1)

  1. Remove the oil pipe No. 1 or No. 2.

  1. Remove the oil control valve filter.

  1. Check that the filter and pipe are not clogged.

    OK:
    The filter and pipe are not clogged.


NG
CLEAN OIL CONTROL VALVE FILTER
OK


7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

NEXT


8.READ VALUE OF INTELLIGENT TESTER (CHECK IF DTC OUTPUT RECURS)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester ON.

  1. Clear DTCs.

  1. Start the engine and warm up.

  1. Switch the ECM from normal mode using the check mode using the tester (Click here).

  1. Driver the vehicle for more than 10 minutes.

  1. Read output DTCs using the intelligent tester.

    Standard:
    No DTC output.
    HINT:
    DTC P0011, P0012, P0021 or P0022 is output when foreign objects in engine oil are caught in some parts of the system. These codes will stay registered even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.


OK
SYSTEM OK
NG

REPLACE ECM