Black Out Tape (For Rear Door) Removal

Vehicle Exterior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Exterior Panels Trim. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. PRECAUTION

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  3. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH

  4. REMOVE REAR DOOR ARMREST BASE PANEL ASSEMBLY LH

  5. REMOVE ASSIST GRIP COVER LH

  6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  7. REMOVE REAR INNER DOOR GLASS WEATHERSTRIP LH

  8. REMOVE REAR DOOR SERVICE HOLE COVER LH

  9. REMOVE REAR DOOR GLASS RUN LH

  10. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH

  11. REMOVE REAR DOOR QUARTER WINDOW GLASS LH

  12. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

  13. REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH

  14. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING LH

  15. REMOVE REAR DOOR FRAME GARNISH LH

  16. REMOVE REAR NO. 2 DOOR FRAME GARNISH LH

  17. REMOVE REAR DOOR WEATHERSTRIP LH

  18. REMOVE NO. 2 BLACK OUT TAPE LH

  19. REMOVE NO. 6 BLACK OUT TAPE LH

  20. REMOVE UPPER INNER BLACK OUT TAPE LH

  21. REMOVE REAR INNER BLACK OUT TAPE LH

Black Out Tape (For Rear Door) -- Removal


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.
  3. When removing the black out tape and window frame moulding, heat the vehicle body, black out tape and window frame moulding using a heat light.
Standard Heating Temperature:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Black Out Tape
20 to 30°C (68 to 86°F)
Window Frame Moulding
20 to 30°C (68 to 86°F)
NOTICE:
Do not heat the vehicle body, black out tape and window frame moulding excessively.


1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Exterior Panels Trim.Front Bumper (For Standard).Black Out Tape (For Rear Door) Removal

  1. Using a screwdriver, detach the 4 claws and remove the rear door inside handle bezel LH.

    HINT:
    Tape the screwdriver tip before use.
    Text in Illustration
    *1
    		Protective Tape


4. REMOVE REAR DOOR ARMREST BASE PANEL ASSEMBLY LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a moulding remover, detach the 7 claws.

  1. Disconnect the connector and remove the armrest base panel.



5. REMOVE ASSIST GRIP COVER LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a moulding remover, detach the 9 claws and remove the assist grip cover LH.



6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Exterior Panels Trim.Front Bumper (For Standard).Black Out Tape (For Rear Door) Removal

  1. Remove the 3 screws.

  1. Remove the 9 clips.

  1. Remove the rear inner door glass weatherstrip LH together with the rear door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.

    HINT:
    Make sure that the pin labeled A in the illustration is detached from the door panel.

  1. Disconnect the connector and remove the rear door trim board sub-assembly LH.



    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Disconnect the 2 cables from the rear door inside handle sub-assembly LH.



7. REMOVE REAR INNER DOOR GLASS WEATHERSTRIP LH

  1. Remove the rear door quarter window weatherstrip LH.



8. REMOVE REAR DOOR SERVICE HOLE COVER LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Exterior Panels Trim.Front Bumper (For Standard).Black Out Tape (For Rear Door) Removal

  1. Using a clip remover, detach the 6 clamps.

  1. Remove the bolt and disconnect the 2 connectors.

  1. Remove the rear door service hole cover LH.

    HINT:
    Remove the remaining tape on the door.


9. REMOVE REAR DOOR GLASS RUN LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the rear door glass run LH from the window frame.



10. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the 2 bolts.

  1. Remove the screw and rear door rear lower window frame sub-assembly LH.



11. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the rear door quarter window glass LH and rear door quarter window weatherstrip LH as a unit as shown in the illustration.



12. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the rear door glass sub-assembly LH from the rear door window regulator sub-assembly LH as shown in the illustration.

    NOTICE:
    Do not damage the door glass.


13. REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH


Land Cruiser. Urj200, 202 Grj200 Vdj200.Exterior Panels Trim.Front Bumper (For Standard).Black Out Tape (For Rear Door) Removal

  1. Put protective tape around the belt moulding.



    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Detach the claw and remove the belt moulding.



14. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING LH


Land Cruiser. Urj200, 202 Grj200 Vdj200.Exterior Panels Trim.Front Bumper (For Standard).Black Out Tape (For Rear Door) Removal

  1. Put protective tape around the window frame moulding.

  1. Detach the clip and remove the double-sided tape to remove the window frame moulding.



15. REMOVE REAR DOOR FRAME GARNISH LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Detach the clip and remove the rear door frame garnish LH.

    HINT:
    This clip needs to be replaced with a new one because the clip will break when removing the rear door frame garnish LH.


16. REMOVE REAR NO. 2 DOOR FRAME GARNISH LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Detach the clip and remove the rear No. 2 door frame garnish LH.

    HINT:
    This clip needs to be replaced with a new one because the clip will break when removing the rear No. 2 door frame garnish LH.


17. REMOVE REAR DOOR WEATHERSTRIP LH


Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Detach the 4 clips, and remove the upper part of the rear door weatherstrip so that the black out tape can be removed.



18. REMOVE NO. 2 BLACK OUT TAPE LH


Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Pull back an edge of the black out tape and pull it parallel to the vehicle body to remove it.



19. REMOVE NO. 6 BLACK OUT TAPE LH


Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Pull back an edge of the black out tape and pull it parallel to the vehicle body to remove it.



20. REMOVE UPPER INNER BLACK OUT TAPE LH


Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Pull back an edge of the black out tape and pull it parallel to the vehicle body to remove it.



21. REMOVE REAR INNER BLACK OUT TAPE LH


Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Pull back an edge of the black out tape and pull it parallel to the vehicle body to remove it.