Rear Door Belt Moulding Removal

Vehicle Exterior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Exterior Panels Trim. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. PRECAUTION

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  3. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH

  4. REMOVE REAR DOOR ARMREST BASE PANEL ASSEMBLY LH

  5. REMOVE ASSIST GRIP COVER LH

  6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  7. REMOVE REAR INNER DOOR GLASS WEATHERSTRIP LH

  8. REMOVE REAR DOOR SERVICE HOLE COVER LH

  9. REMOVE REAR DOOR GLASS RUN LH

  10. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH

  11. REMOVE REAR DOOR QUARTER WINDOW GLASS LH

  12. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

  13. REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH

Rear Door Belt Moulding -- Removal


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a screwdriver, detach the 4 claws and remove the rear door inside handle bezel LH.

    HINT:
    Tape the screwdriver tip before use.
    Text in Illustration
    Land Cruiser. Urj200, 202 Grj200 Vdj200
    		Protective Tape


4. REMOVE REAR DOOR ARMREST BASE PANEL ASSEMBLY LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a moulding remover, detach the 7 claws.

  1. Disconnect the connector and remove the rear door upper armrest base panel assembly LH.



5. REMOVE ASSIST GRIP COVER LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a moulding remover, detach the 9 claws and remove the assist grip cover LH.



6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Exterior Panels Trim.Front Bumper (For Standard).Rear Door Belt Moulding Removal

  1. Remove the 3 screws.

  1. Remove the 9 clips.

  1. Remove the rear inner door glass weatherstrip LH together with the rear door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.

    HINT:
    Make sure that the pin labeled A in the illustration is detached from the door panel.

  1. Disconnect the connector and remove the rear door trim board sub-assembly LH.



    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Disconnect the 2 cables from the rear door inside handle sub-assembly LH.



7. REMOVE REAR INNER DOOR GLASS WEATHERSTRIP LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Detach the 4 clips and remove the rear door inner glass weatherstrip LH from the rear door trim board sub-assembly LH.

    NOTICE:
    1. Squeeze the metal clip to remove it.
    2. The metal clip may be deformed if it is forcibly pulled.


8. REMOVE REAR DOOR SERVICE HOLE COVER LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a clip remover, detach the 7clamps.

  1. Remove the bolt and disconnect the 3connectors.

  1. Remove the rear door service hole cover LH.

    HINT:
    Remove the remaining tape on the door.


9. REMOVE REAR DOOR GLASS RUN LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the rear door glass run LH from the window frame.



10. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the 2 bolts.

  1. Remove the screw and rear door rear lower window frame sub-assembly LH.



11. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the rear door quarter window glass LH and rear door quarter window weatherstrip LH as a unit as shown in the illustration.



12. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the rear door glass sub-assembly LH from the rear door window regulator sub-assembly LH as shown in the illustration.

    NOTICE:
    Do not damage the door glass.


13. REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH


Land Cruiser. Urj200, 202 Grj200 Vdj200.Exterior Panels Trim.Front Bumper (For Standard).Rear Door Belt Moulding Removal

  1. Put protective tape around the belt moulding.



    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Detach the claw and remove the belt moulding.