Dtc B2417 Headlight Beam Level Control Motor Lh Malfunction

Vehicle Exterior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Lighting (Ext). Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK FOR DTC

PERFORM ACTIVE TEST USING GTS (HL AUTO LEVELING)

CHECK HEADLIGHT LEVELING MOTOR

CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - BATTERY AND BODY GROUND)

CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - HEADLIGHT UNIT ASSEMBLY)

INSPECT HEADLIGHT UNIT ASSEMBLY

CHECK HEADLIGHT LEVELING MOTOR

DTC B2417 Headlight Beam Level Control Motor LH Malfunction

DTC B2418 Headlight Beam Level Control Motor RH Malfunction


DESCRIPTION

The headlight leveling motor receives a signal from the headlight swivel ECU to operate. The headlight swivel ECU receives a signal indicating the operating conditions of the headlight leveling motor.

DTC Code
DTC Detection Condition
Trouble Area
B2417
  1. Malfunction in the headlight leveling motor LH.
  2. Open or short in the headlight leveling motor LH circuit.
  1. Headlight swivel ECU assembly
  2. Headlight unit assembly LH
  3. Headlight leveling motor LH
  4. Harness or connector
B2418
  1. Malfunction in the headlight leveling motor RH.
  2. Open or short in the headlight leveling motor RH circuit.
  1. Headlight swivel ECU assembly
  2. Headlight unit assembly RH
  3. Headlight leveling motor RH
  4. Harness or connector

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Lighting (Ext).Lighting System. Dtc B2417 Headlight Beam Level Control Motor Lh Malfunction


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. After replacing the headlight swivel ECU, initialization of the ECU is necessary (Click here).
1.CHECK FOR DTC

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2417 or B2418 output does not occur.


NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2.PERFORM ACTIVE TEST USING GTS (HL AUTO LEVELING)

  1. Using the GTS, perform the Active Test (Click here).

    AFS
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    HL Auto Leveling
    		This test activates the Leveling Motor of the LH and RH headlights. By activating the Leveling Motor, illumination direction of the headlights can be moved up/down.
    		Up, Down, Stop
    		Perform the Active Test with the vehicle stopped, the ignition switch ON and the low beam headlights on.
    OK:
    Headlight leveling motors operate normally.


NG
Go to step 4
OK


3.CHECK HEADLIGHT LEVELING MOTOR

  1. Temporarily replace the headlight leveling motor with a new or normally functioning one (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2417 or B2418 output does not occur.
    Result
    Result
    		Proceed to
    OK
    		A
    NG (for LHD)
    		B
    NG (for RHD)
    		C


B
REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY (Click here)

C
REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY (Click here)
A

END (HEADLIGHT LEVELING MOTOR WAS DEFECTIVE)

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - BATTERY AND BODY GROUND)


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Lighting (Ext).Lighting System. Dtc B2417 Headlight Beam Level Control Motor Lh Malfunction

  1. Disconnect the headlight swivel ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    E101-15 (IG) - Body ground
    		Ignition switch ON
    		11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    E101-22 (E1) - Body ground
    		Always
    		Below 1 Ω
Text in Illustration
*a
Front view of wire harness connector
(to Headlight Swivel ECU Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - HEADLIGHT UNIT ASSEMBLY)

  1. Disconnect the E101 headlight swivel ECU connector.

  1. Disconnect the A66*1 or A69*2 headlight unit connector.

    1. *1: for LH
    2. *2: for RH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    		Condition
    		Specified Condition
    E101-1 (SMBL) - A66-2 (LHIG)
    		Always
    		Below 1 Ω
    E101-30 (LH+) - A66-3 (LH T)
    		Always
    		Below 1 Ω
    E101-27 (LH-) - A66-1 (LH E)
    		Always
    		Below 1 Ω
    E101-1 (SMBL) - Body ground
    		Always
    		10 kΩ or higher
    E101-30 (LH+) - Body ground
    		Always
    		10 kΩ or higher
    E101-27 (LH-) - Body ground
    		Always
    		10 kΩ or higher
    for RH:
    Tester Connection
    		Condition
    		Specified Condition
    E101-2 (SMBR) - A69-2 (RHIG)
    		Always
    		Below 1 Ω
    E101-11 (RH+) - A69-3 (RH T)
    		Always
    		Below 1 Ω
    E101-28 (RH-) - A69-1 (RH E)
    		Always
    		Below 1 Ω
    E101-2 (SMBR) - Body ground
    		Always
    		10 kΩ or higher
    E101-11 (RH+) - Body ground
    		Always
    		10 kΩ or higher
    E101-28 (RH-) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT HEADLIGHT UNIT ASSEMBLY


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Lighting (Ext).Lighting System. Dtc B2417 Headlight Beam Level Control Motor Lh Malfunction

  1. Remove the headlight unit (Click here).

  1. Disconnect the headlight leveling motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    		Condition
    		Specified Condition
    2 (LHIG) - 1
    		Always
    		Below 1 Ω
    3 (LH T) - 2
    1 (LH E) - 3
    for RH:
    Tester Connection
    		Condition
    		Specified Condition
    2 (RHIG) - 1
    		Always
    		Below 1 Ω
    3 (RH T) - 2
    1 (RH E) - 3
    Text in Illustration
    *A
    		for LH
    *B
    		for RH
    *a
    		Front view of wire harness connector
    (to Headlight Leveling Motor)
    *b
    		Front view of wire harness connector


NG
REPLACE HEADLIGHT UNIT ASSEMBLY (Click here)
OK


7.CHECK HEADLIGHT LEVELING MOTOR

  1. Temporarily replace the headlight leveling motor with a new or normally functioning one (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2417 or B2418 output does not occur.
    Result
    Result
    		Proceed to
    OK
    		A
    NG (for LHD)
    		B
    NG (for RHD)
    		C


B
REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY (Click here)

C
REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY (Click here)
A

END (HEADLIGHT LEVELING MOTOR WAS DEFECTIVE)