Dtc B2416 Height Control Sensor Malfunction

Vehicle Exterior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Lighting (Ext). Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK FOR DTC

CHECK VEHICLE TYPE

READ VALUE USING GTS (REAR HEIGHT CONTROL SENSOR)

CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH)

INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

READ VALUE USING GTS (REAR HEIGHT CONTROL SENSOR)

CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH)

INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

DTC B2416 Height Control Sensor Malfunction

DTC B241A Rear Height Control Sensor


DESCRIPTION

The DTC is stored when the headlight swivel ECU*1 or headlight leveling ECU*2 detects malfunctions in the rear height control sensor LH power source.
  1. *1: w/ Dynamic Headlight Auto Leveling
  2. *2: w/ Static Headlight Auto Leveling

DTC Code
DTC Detection Condition
Trouble Area
B2416
  1. Malfunction in the rear height control sensor LH.
  2. Open or short in the rear height control sensor LH power source circuit.
  1. Rear height control sensor sub-assembly LH
  2. Headlight swivel ECU assembly (w/ Dynamic Headlight Auto Leveling)
  3. Headlight leveling ECU assembly (w/ Static Headlight Auto Leveling)
  4. Harness or connector
B241A
  1. Malfunction in the rear height control sensor LH.
  2. Open or short in the rear height control sensor LH circuit.
  1. Rear height control sensor sub-assembly LH
  2. Headlight swivel ECU assembly (w/ Dynamic Headlight Auto Leveling)
  3. Headlight leveling ECU assembly (w/ Static Headlight Auto Leveling)
  4. Harness or connector

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Lighting (Ext).Lighting System. Dtc B2416 Height Control Sensor Malfunction


Land Cruiser. Urj200, 202 Grj200 Vdj200.Lighting (Ext).Lighting System. Dtc B2416 Height Control Sensor Malfunction


INSPECTION PROCEDURE

NOTICE:
After replacing the headlight leveling ECU*1 or headlight swivel ECU*2 and rear height control sensor LH, initialization of the ECU is necessary (Click here).
  1. *1: w/ Static Headlight Auto Leveling
  2. *2: w/ Dynamic Headlight Auto Leveling
1.CHECK FOR DTC

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2416 or B241A output does not occur.


NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2.CHECK VEHICLE TYPE

  1. Check the vehicle type.

    Result
    Result
    		Proceed to
    w/ Static Headlight Auto Leveling
    		A
    w/ Dynamic Headlight Auto Leveling
    		B


B
Go to step 6
A


3.READ VALUE USING GTS (REAR HEIGHT CONTROL SENSOR)

  1. Using the GTS, read the Data List (Click here).

    HL Auto Leveling
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Height Sens Pw Supply Val
    		Rear height control sensor power supply value / 0 to 5 V
    		4.7 to 5.2 V
    		-
    Rr Height Sens Signal Val
    		Rear height control sensor signal value / 0 to 5 V
    		Approximately 2.5 V (When vehicle level)
    		The value changes according to the vehicle height.
    OK:
    Normal conditions listed above are displayed.


NG
Go to step 4
OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY (Click here)

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH)

  1. Disconnect the E109 headlight leveling ECU connector.

  1. Disconnect the N7 rear height control sensor LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    E109-12 (SBR) - N7-1 (SHB)
    		Always
    		Below 1 Ω
    E109-19 (SHRL) - N7-2 (SHRL)
    		Always
    		Below 1 Ω
    E109-21 (SGR) - N7-3 (SHG)
    		Always
    		Below 1 Ω
    E109-12 (SBR) - Body ground
    		Always
    		10 kΩ or higher
    E109-19 (SHRL) - Body ground
    		Always
    		10 kΩ or higher
    E109-21 (SGR) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

  1. Remove the rear height control sensor LH (Click here).

  1. Inspect the rear height control sensor LH (Click here).



NG
REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (Click here)
OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY (Click here)

6.READ VALUE USING GTS (REAR HEIGHT CONTROL SENSOR)

  1. Using the GTS, read the Data List (Click here).

    AFS
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Height Sens Pw Supply Val
    		Height control sensor power supply value / 0 to 6.25 V
    		4.7 to 5.2 V
    		-
    Rr Height Sens Signal Val
    		Rear height control sensor signal value / 0 to 5 V
    		Approximately 2.5 V (When vehicle level)
    		The value changes according to the vehicle height.
    OK:
    Normal conditions listed above are displayed.
    Result
    Result
    		Proceed to
    OK (for LHD)
    		A
    OK (for RHD)
    		B
    NG
    		C


B
REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY (Click here)

C
Go to step 7
A

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY (Click here)

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH)

  1. Disconnect the E101 headlight swivel ECU connector.

  1. Disconnect the N7 rear height control sensor LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    E101-18 (SBR) - N7-1 (SHB)
    		Always
    		Below 1 Ω
    E101-19 (SHRL) - N7-2 (SHRL)
    		Always
    		Below 1 Ω
    E109-21 (SGR) - N7-3 (SHG)
    		Always
    		Below 1 Ω
    E101-18 (SBR) - Body ground
    		Always
    		10 kΩ or higher
    E101-19 (SHRL) - Body ground
    		Always
    		10 kΩ or higher
    E109-21 (SGR) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

  1. Remove the rear height control sensor LH (Click here).

  1. Inspect the rear height control sensor LH (Click here).

    Result
    Result
    		Proceed to
    OK (for LHD)
    		A
    OK (for RHD)
    		B
    NG
    		C


B
REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY (Click here)

C
REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (Click here)
A

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY (Click here)