Lighting System Data List / Active Test

Vehicle Exterior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Lighting (Ext). Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. DATA LIST

  1. ACTIVE TEST

Lighting System -- Data List / Active Test



DATA LIST
HINT:
Using the GTS to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Enter the following menus: Body / (desired system) / Data List.

  5. According to the display on the GTS, read the Data List.

    Main Body
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    ACC SW
    		Ignition switch ACC signal / ON or OFF
    		ON: Ignition witch ACC
    OFF: Ignition switch off
    		"ON" is also displayed for this item when the ignition switch ON.
    IG SW
    		Ignition switch ON signal / ON or OFF
    		ON: Ignition switch ON
    OFF: Ignition switch off
    		"OFF" is also displayed for this item when the ignition switch ACC.
    FL Door Courtesy SW
    		Front door courtesy light switch LH signal / ON or OFF
    		ON: Front door courtesy light switch LH on
    OFF: Front door courtesy light switch LH off
    		-
    FR Door Courtesy SW
    		Front door courtesy light switch RH signal / ON or OFF
    		ON: Front door courtesy light switch RH on
    OFF: Front door courtesy light switch RH off
    		-
    RR Door Courtesy SW
    		Rear door courtesy light switch RH signal / ON or OFF
    		ON: Rear door courtesy light switch RH on
    OFF: Rear door courtesy light switch RH off
    		-
    RL Door Courtesy SW
    		Rear door courtesy light switch LH signal / ON or OFF
    		ON: Rear door courtesy light switch LH on
    OFF: Rear door courtesy light switch LH off
    		-
    Back Door Courtesy SW
    		Back door courtesy light switch signal / ON or OFF
    		ON: Back door courtesy light switch on
    OFF: Back door courtesy light switch off
    		-
    Dimmer SW
    		Dimmer switch signal / ON or OFF
    		ON: Dimmer switch on or passing light switch on
    OFF: Dimmer switch off
    		-
    Passing Light SW
    		Passing light switch signal / ON or OFF
    		ON: Passing light switch on
    OFF: Passing light switch off
    		-
    Front Fog Light SW
    		Front fog light switch signal / ON or OFF
    		ON: Front fog light switch on
    OFF: Front fog light switch off
    		w/ Front Fog Light
    Auto Light SW
    		Auto light switch signal / ON or OFF
    		ON: Auto light switch on
    OFF: Auto light switch off
    		-
    Head Light SW (Head)
    		Headlight switch signal / ON or OFF
    		ON: Headlight switch (Head) on
    OFF: Headlight switch (Head) off
    		-
    Head Light SW (Tail)
    		Taillight switch signal / ON or OFF
    		ON: Headlight switch (Tail) on
    OFF: Headlight switch (Tail) on
    		-
    Illumination Rate Info
    		Illumination rate / min.: 0, max.: 99.99
    		Actual illumination rate displayed
    		-
    I/L ON W/Door Key Unlock
    		Interior light ON with unlock / ON or OFF
    		Customize setting displayed
    		-
    Lighting Time
    		Lighting Time / 7.5s or 15s or 30s
    		Customize setting displayed
    		-
    I/L when ACC OFF
    		I/L ON/ACC OFF Light the I/L when ACC OFF / ON or OFF
    		Customize setting displayed
    		-
    Sensitivity
    		Turn on luminous intensity / DARK1, DARK2, NORMAL, LIGHT1, LIGHT2
    		Customize setting displayed
    		-
    AFS/AHS ECU High Beam Control
    		Low and high beam control / Not Apply or Apply
    		Not Apply: Low and high beam control disabled
    Apply: Low and high beam control enabled
    		-
    AFS/AHS ECU High Beam Light Status
    		High beam illumination / ON or OFF
    		ON: High beams illuminated by headlight leveling ECU
    OFF: High beams turned off by headlight leveling ECU
    		-
    Auto H Beam STS0
    		Automatic high beam sensor current state / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err
    		Current condition displayed
    		Undetec: undetected
    CAM NA: camera detection malfunction*
    No sens: no detection
    Hlight: oncoming vehicles with headlights on
    Taillgt: preceding vehicles with taillights on
    Speed: vehicle speed
    Daytime: daytime state
    Village: urban area Malfunc:
    Delay: standby mode
    Aim Lmt: aiming misalignment
    SAE Mod: SAE mode
    Undefin: undefined state
    LIN Err: LIN communication error
    Auto H Beam STS1
    		Automatic high beam sensor current state past 1 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err
    		Current condition displayed
    		Undetec: undetected
    CAM NA: camera detection malfunction*
    No sens: no detection
    Hlight: oncoming vehicles with headlights on
    Taillgt: preceding vehicles with taillights on
    Speed: vehicle speed
    Daytime: daytime state
    Village: urban area Malfunc:
    Delay: standby mode
    Aim Lmt: aiming misalignment
    SAE Mod: SAE mode
    Undefin: undefined state
    LIN Err: LIN communication error
    Auto H Beam STS2
    		Automatic high beam sensor current state past 2 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err
    		Current condition displayed
    		Undetec: undetected
    CAM NA: camera detection malfunction*
    No sens: no detection
    Hlight: oncoming vehicles with headlights on
    Taillgt: preceding vehicles with taillights on
    Speed: vehicle speed
    Daytime: daytime state
    Village: urban area Malfunc:
    Delay: standby mode
    Aim Lmt: aiming misalignment
    SAE Mod: SAE mode
    Undefin: undefined state
    LIN Err: LIN communication error
    Auto H Beam STS3
    		Automatic high beam sensor current state past 3 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err
    		Current condition displayed
    		Undetec: undetected
    CAM NA: camera detection malfunction*
    No sens: no detection
    Hlight: oncoming vehicles with headlights on
    Taillgt: preceding vehicles with taillights on
    Speed: vehicle speed
    Daytime: daytime state
    Village: urban area Malfunc:
    Delay: standby mode
    Aim Lmt: aiming misalignment
    SAE Mod: SAE mode
    Undefin: undefined state
    LIN Err: LIN communication error
    Auto H Beam STS4
    		Automatic high beam sensor current state past 4 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err
    		Current condition displayed
    		Undetec: undetected
    CAM NA: camera detection malfunction*
    No sens: no detection
    Hlight: oncoming vehicles with headlights on
    Taillgt: preceding vehicles with taillights on
    Speed: vehicle speed
    Daytime: daytime state
    Village: urban area Malfunc:
    Delay: standby mode
    Aim Lmt: aiming misalignment
    SAE Mod: SAE mode
    Undefin: undefined state
    LIN Err: LIN communication error
    Auto H Beam STS5
    		Automatic high beam sensor current state past 5 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err
    		Current condition displayed
    		Undetec: undetected
    CAM NA: camera detection malfunction*
    No sens: no detection
    Hlight: oncoming vehicles with headlights on
    Taillgt: preceding vehicles with taillights on
    Speed: vehicle speed
    Daytime: daytime state
    Village: urban area Malfunc:
    Delay: standby mode
    Aim Lmt: aiming misalignment
    SAE Mod: SAE mode
    Undefin: undefined state
    LIN Err: LIN communication error
    Auto H Beam STS6
    		Automatic high beam sensor current state past 6 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err
    		Current condition displayed
    		Undetec: undetected
    CAM NA: camera detection malfunction*
    No sens: no detection
    Hlight: oncoming vehicles with headlights on
    Taillgt: preceding vehicles with taillights on
    Speed: vehicle speed
    Daytime: daytime state
    Village: urban area Malfunc:
    Delay: standby mode
    Aim Lmt: aiming misalignment
    SAE Mod: SAE mode
    Undefin: undefined state
    LIN Err: LIN communication error
    Auto H Beam STS7
    		Automatic high beam sensor current state past 7 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err
    		Current condition displayed
    		Undetec: undetected
    CAM NA: camera detection malfunction*
    No sens: no detection
    Hlight: oncoming vehicles with headlights on
    Taillgt: preceding vehicles with taillights on
    Speed: vehicle speed
    Daytime: daytime state
    Village: urban area Malfunc:
    Delay: standby mode
    Aim Lmt: aiming misalignment
    SAE Mod: SAE mode
    Undefin: undefined state
    LIN Err: LIN communication error

    1. *: If CAM NA is displayed, the forward recognition camera*1 or inner rear view mirror*2 may have stopped operating due to high temperature.
    2. *1: w/ Pre-crash Safety System
    3. *2: w/o Pre-crash Safety System

    HL Auto Leveling (w/ Static Headlight Auto Leveling)
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Headlight Low Beam State
    		Low beam headlight state / ON or OFF
    		ON: Low beam headlights on
    OFF: Low beam headlights off
    		-
    Headlight High Beam State
    		High beam headlight state / ON or OFF
    		ON: High beam headlights on
    OFF: High beam headlights off
    		-
    +B
    		Ignition power supply voltage value / 0 to 19.75 V
    		11 to 14 V
    		-
    Height Sens Pw Supply Val
    		Rear height control sensor power supply value / 0 to 5 V
    		Approximately 5 V
    		-
    Rr Height Sens Signal Val
    		Rear height control sensor signal value / 0 to 5 V
    		Approximately 2.5 V (When vehicle level)
    		The value changes according to the vehicle height
    Front Right Wheel Speed Value
    		Front right wheel speed / 0 to 327.67 km/h
    		Condition can be displayed
    		-
    Front Left Wheel Speed Value
    		Front left wheel speed / 0 to 327.67 km/h
    		Condition can be displayed
    		-
    Vehicle Speed
    		Vehicle speed / 0 to 327.67 km/h
    		Actual vehicle speed
    		-
    Rear Height Adjust Value
    		Result of rear vehicle height calibration / Valid or Inval
    		Valid: Rear vehicle height calibration completed
    Inval: Rear vehicle height calibration not completed
    		-
    Rear Height Adjust Valid Flag
    		Rear height adjustment range / Valid or Inval
    		Condition can be displayed
    		-
    Init Writing Count
    		Number of times initialization performed / 0 to 255
    		Current condition displayed
    		-
    Sensor Initialization Hist
    		Sensor initialization history / not comp, 10%, 25%, 50%, 75%, 100% or complied
    		Current condition displayed
    		-
    Left and Right Leveling Target Step
    		Left and right leveling motor target step
    		0 to 500 step
    		-
    Left Leveling Step
    		Left leveling motor target step
    		0 to 500 step
    		-
    Right Leveling Step
    		Right leveling motor target step
    		0 to 500 step
    		-
    Number Of Trouble Codes
    		Number of trouble codes / 0 to 255
    		Condition can be displayed
    		-

    AFS (w/ Dynamic Headlight Auto Leveling)
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Headlight Low Beam State
    		Low beam headlight state / ON or OFF
    		ON: Low beam headlights on
    OFF: Low beam headlights off
    		-
    Headlight High Beam State
    		High beam headlight state / ON or OFF
    		ON: High beam headlights on
    OFF: High beam headlights off
    		-
    +B
    		Ignition power supply voltage value / 0 to 19.75 V
    		11 to 14 V
    		-
    Height Sens Pw Supply Val
    		Rear height control sensor power supply value / 0 to 5 V
    		Approximately 5 V
    		-
    Rr Height Sens Signal Val
    		Rear height control sensor signal value / 0 to 5 V
    		Approximately 2.5 V (When vehicle level)
    		The value changes according to the vehicle height
    Front Right Wheel Speed Value
    		Front right wheel speed / 0 to 327.67 km/h
    		Condition can be displayed
    		-
    Front Left Wheel Speed Value
    		Front left wheel speed / 0 to 327.67 km/h
    		Condition can be displayed
    		-
    Vehicle Speed
    		Vehicle speed / 0 to 327.67 km/h
    		Actual vehicle speed
    		-
    Rear Height Adjust Value
    		Result of rear vehicle height calibration / Valid or Inval
    		Valid: Rear vehicle height calibration completed
    Inval: Rear vehicle height calibration not completed
    		-
    Rear Height Adjust Valid Flag
    		Rear height adjustment range / Valid or Inval
    		Condition can be displayed
    		-
    Init Writing Count
    		Number of times initialization performed / 0 to 255
    		Current condition displayed
    		-
    Sensor Initialization Hist
    		Sensor initialization history / not comp, 10%, 25%, 50%, 75%, 100% or complied
    		Current condition displayed
    		-
    Left and Right Leveling Target Step
    		Left and right leveling motor target step
    		0 to 500 step
    		-
    Left Leveling Step
    		Left leveling motor target step
    		0 to 500 step
    		-
    Right Leveling Step
    		Right leveling motor target step
    		0 to 500 step
    		-
    Number Of Trouble Codes
    		Number of trouble codes / 0 to 255
    		Condition can be displayed
    		-

    Combination Meter
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Turn Signal Switch (Right)
    		Turn signal switch (right) signal / ON or OFF
    		ON: Turn signal switch (right) on OFF: Turn signal switch (right) off
    		-
    Turn Signal Switch (Left)
    		Turn signal switch (left) signal / ON or OFF
    		ON: ON: Turn signal switch (left) on OFF: Turn signal switch (left) off
    		-
    Hazard Flasher Switch
    		Hazard switch signal / ON or OFF
    		ON: Hazard switch on
    OFF: Hazard switch off
    		-

ACTIVE TEST
HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the GTS to the DLC3.

  2. Turn the Ignition switch to ON.

  3. Turn the GTS on.

  4. Enter the following menus: Body / (desired system) / Active Test.

  5. According to the display on the GTS, perform the Active Test.

    Main Body
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Daytime Running Light
    		DRL light illumination operation
    		ON or OFF
    		Only when "Daytime Running Light" in the Techstream customization settings is set to "ON".
    Illuminated Entry System
    		Rear interior foot light illumination operation
    		ON or OFF
    		-
    Fr Front Light
    		Front light
    		ON or OFF
    		-
    Taillight Relay
    		Taillight
    		ON or OFF
    		-
    Headlight Relay
    		Headlight
    		ON or OFF
    		-
    Head Light Hi
    		Headlight (Hi)
    		ON or OFF
    		-
    Front Fog Light Relay
    		Front fog light
    		ON or OFF
    		Check the operation with the taillight illuminated.
    Relay for Interior Light Auto Cut Function
    		DOME CUT relay
    		ON or OFF
    		The Active Test for this item cannot be performed with the ignition switch on. Therefore, after selecting this item with the ignition switch on, turn the ignition switch off and perform the Active Test.
    Interior Illumination Light1
    		Turns on the rear door illumination
    		ON or OFF
    		-

    HL Auto Leveling (w/ Static Headlight Auto Leveling)
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    HL Auto Leveling
    		This test activates the Leveling Motor of the LH and RH headlights. By activating the Leveling Motor, illumination direction of the headlights can be moved up/down.
    		Up, Down, Stop
    		Perform the Active Test with the vehicle stopped, the ignition switch ON and the low beam headlights on.

    AFS (w/ Dynamic Headlight Auto Leveling)
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    HL Auto Leveling
    		This test activates the Leveling Motor of the LH and RH headlights. By activating the Leveling Motor, illumination direction of the headlights can be moved up/down.
    		Up, Down, Stop
    		Perform the Active Test with the vehicle stopped, the ignition switch ON and the low beam headlights on.

    Body No. 4 (w/ Side Step Light)
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Rear Step Light
    		Step light operation
    		OFF/ON
    		-