Outer Rear View Mirror Removal

Vehicle Exterior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Mirror (Ext). Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. PRECAUTION

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  3. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

  4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH

  5. REMOVE FRONT UPPER ARMREST BASE PANEL LH

  6. REMOVE DOOR ASSIST GRIP COVER LH

  7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

  8. REMOVE FRONT INNER DOOR GLASS WEATHERSTRIP LH

  9. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY

Outer Rear View Mirror -- Removal


HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the LH side.


1. PRECAUTION
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Detach the clip and claw, and remove the front door lower frame bracket garnish LH.



4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a screwdriver, detach the 4 claws and remove the front door inside handle bezel LH.

    HINT:
    Tape the screwdriver tip before use.
    Text in Illustration
    Land Cruiser. Urj200, 202 Grj200 Vdj200
    		Protective Tape


5. REMOVE FRONT UPPER ARMREST BASE PANEL LH


Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a moulding remover, detach the 5 claws.

  1. Disconnect the connector and remove the armrest base panel.



6. REMOVE DOOR ASSIST GRIP COVER LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a moulding remover, detach the 8 claws and remove the door assist grip cover LH.



7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Mirror (Ext).Power Mirror Control System (W/ Retract Mirror).Outer Rear View Mirror Removal

  1. Remove the 3 screws.

  1. Remove the 13 clips.

  1. Remove the front inner door glass weatherstrip LH together with the front door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.

    HINT:
    Make sure that the pin labeled A in the illustration is detached from the door panel.

  1. Disconnect the each connector.



    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Disconnect the 2 cables from the front door inside handle sub-assembly LH.



8. REMOVE FRONT INNER DOOR GLASS WEATHERSTRIP LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Detach the 4 clips and remove the front inner door glass weatherstrip LH from the front door trim board sub-assembly LH.

    NOTICE:
    1. Squeeze the metal clip to remove it.
    2. The metal clip may be deformed if it is forcibly pulled.


9. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY


Land Cruiser. Urj200, 202 Grj200 Vdj200.Mirror (Ext).Power Mirror Control System (W/ Retract Mirror).Outer Rear View Mirror Removal

  1. w/ Power Mirror Control System:

    1. Disconnect the connector labeled A.

    2. Detach the clamp.

  1. Remove the 3 nuts and claw.

  1. Remove the outer rear view mirror.