Tail Gate Closer System Data List / Active Test

Vehicle Exterior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Door Hatch. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. DATA LIST

  1. ACTIVE TEST

Tail Gate Closer System -- Data List / Active Test



DATA LIST
HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Body No. 4 / Data List.

  5. According to the display on the tester, read the Data List.

    Body No. 4
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Handle Switch of tail gate panel
    		Back door remote control signal / ON or OFF
    		ON: Back door remote control pulled
    OFF: Back door remote control free
    		-
    Half Latch Switch RH
    		Half-latch switch RH signal / ON or OFF
    		ON: Lower tail gate open
    OFF: Lower tail gate closed
    		-
    Half Latch Switch LH
    		Half-latch switch LH signal / ON or OFF
    		ON: Lower tail gate open
    OFF: Lower tail gate closed
    		-
    Courtesy Switch RH
    		Lower tail gate courtesy switch RH signal / ON or OFF
    		ON: Lower tail gate open
    OFF: Lower tail gate closed
    		-
    Courtesy Switch LH
    		Lower tail gate courtesy switch LH signal / ON or OFF
    		ON: Lower tail gate open
    OFF: Lower tail gate closed
    		-
    Position Switch RH
    		Close position switch RH signal / ON or OFF
    		ON: Lower tail gate closed
    OFF: Lower tail gate open
    		-
    Position Switch LH
    		Close position switch LH signal / ON or OFF
    		ON: Lower tail gate closed
    OFF: Lower tail gate open
    		-
    Luggage Pawl Switch
    		Pawl switch signal / ON or OFF
    		ON: Lower tail gate lock motor operating
    OFF: Lower tail gate open or closed
    		-
    Fail Count RH
    		Number of malfunctions detected in lower tail gate lock RH / 0 to 5
    		Number of detected malfunctions displayed
    		-
    Fail Count LH
    		Number of malfunctions detected in lower tail gate lock LH / 0 to 5
    		Number of detected malfunctions displayed
    		-
    # Codes
    		Number of stored trouble codes / min.: 0, max.: 255
    		Number of DTCs displayed
    		-


ACTIVE TEST
HINT:
Using the intelligent tester to perform the Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Body No. 4 / Active Test.

  5. According to the display on the tester, perform the Active Test.

    Body No. 4
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Tail Gate Panel Open
    		Lower tail gate lock
    		ON / OFF
    		The back door must be open.