Dtc B1447/47 Rear Air Mix Damper Control Servo Motor Circuit On Driver Side

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Heating Air Conditioning. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

READ VALUE USING GTS (AIR MIX SERVO TARG PLS [R], A/M SERVO ACTUAL PULSE[R])

CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING HARNESS ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

CHECK REAR AIR MIX DAMPER SERVO MOTOR (for Driver Side)

CHECK NO. 2 AIR CONDITIONING HARNESS ASSEMBLY

CHECK FOR DTC

DTC B1447/47 Rear Air Mix Damper Control Servo Motor Circuit on Driver Side


DESCRIPTION

  1. *1: for LHD
  2. *2: for RHD
The rear air mix damper servo motor LH*1or RH*2 sends pulse signals to indicate the damper position to the air conditioning amplifier assembly. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the rear air mix damper servo motor LH*1or RH*2 to the appropriate position. This adjusts the amount of air passing through the heater core after passing the evaporator and controls the temperature of the blown air.
HINT:
Confirm that no mechanical problem is present because this trouble code can be output when either a damper link or damper is mechanically locked.

DTC Code
DTC Detection Condition
Trouble Area
B1447/47
The rear air mix damper position does not change even if the air conditioning amplifier assembly operates the rear air mix damper servo motor.
  1. Rear air mix damper servo motor LH*1
  2. Rear air mix damper servo motor RH*2
  3. No. 2 air conditioning harness assembly
  4. Harness or connector
  5. Air conditioning amplifier assembly

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Heating Air Conditioning.Air Conditioning System (For Automatic Air Conditioning System). Dtc B1447/47 Rear Air Mix Damper Control Servo Motor Circuit On Driver Side


INSPECTION PROCEDURE

1.READ VALUE USING GTS (AIR MIX SERVO TARG PLS [R], A/M SERVO ACTUAL PULSE[R])
  1. *1: for LHD
  2. *2: for RHD

  1. Use the Data List to check if the rear air mix damper servo motor LH*1 or RH*2 is functioning properly (Click here).

    Air Conditioner
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Air Mix Servo Targ Pls(R)
    		Rear air mix damper servo motor LH*1 or RH*2 target pulse / Min.: 128, Max.: 383
    for LHD:
    1. MAX COLD: 137 (pulse)
    2. MAX HOT: 182 (pulse)
    for RHD:
    1. MAX COLD: 181 (pulse)
    2. MAX HOT: 136 (pulse)
    1. Displayed between 167 and 182 pulse (for LHD)
    2. Displayed between 139 and 181 pulse (for RHD)
    3. Rear air mix damper servo motor LH*1 or *2 system malfunction
    Air Mix Servo Actual Pluse(R)
    		Rear air mix damper servo motor LH*1 or RH*2 actual pulse / Min.: 128, Max.: 383
    for LHD:
    1. MAX COLD: 137 (pulse)
    2. MAX HOT: 182 (pulse)
    for RHD:
    1. MAX COLD: 181 (pulse)
    2. MAX HOT: 136 (pulse)
    1. Displayed between 167 and 182 pulse (for LHD)
    2. Displayed between 139 and 181 pulse (for RHD)
    3. Rear air mix damper servo motor LH*1 or *2 system malfunction
    OK:
    When the rear temperature adjust switch for driver side is turned from MAX COLD and MAX HOT, the actual pulse changes following the target pulse.
    Result
    Result
    		Proceed to
    Target pulse changes but actual pulse does not change
    		A
    Target pulse and actual pulse do not change
    		B
    Actual pulse changes following the target pulse (When troubleshooting according to the DTC)
    		C
    Actual pulse changes following the target pulse (When troubleshooting according to Problem Symptoms Table)
    		D


B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

C
Go to step 5

E
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A


2.CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING HARNESS ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

  1. Disconnect the K19 No. 2 air conditioning harness assembly connector.

  1. Disconnect the E36 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    K19-2 (RBUG) - E36-12 (RBUG)
    		Always
    		Below 1 Ω
    K19-3 (RBUS) - E36-13 (RBUS)
    		Always
    		Below 1 Ω
    K19-4 (RBBU) - E36-14 (RBBU)
    		Always
    		Below 1 Ω
    K19-2 (RBUG) or E36-12 (RBUG) - Body ground
    		Always
    		10 kΩ or higher
    K19-3 (RBUS) or E36-13 (RBUS) - Body ground
    		Always
    		10 kΩ or higher
    K19-4 (RBBU) or E36-14 (RBBU) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK REAR AIR MIX DAMPER SERVO MOTOR (for Driver Side)

  1. Replace the rear air mix damper servo motor LH*1 or RH*2 (Click here).

    1. *1: for LHD
    2. *2: for RHD
    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a normal one.

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1447/47 is not output.


B
Go to step 4
A

END (REAR AIR MIX DAMPER SERVO MOTOR [for Driver Side] WAS DEFECTIVE)

4.CHECK NO. 2 AIR CONDITIONING HARNESS ASSEMBLY

  1. Replace the No. 2 air conditioning harness assembly with a new or known good one (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1447/47 is not output.


NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

END (NO. 2 AIR CONDITIONING HARNESS ASSEMBLY WAS DEFECTIVE)

5.CHECK FOR DTC

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1447/47 is not output.


NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)